Normal Stereo Reproduction; Displaying The Information About The Input Source - Yamaha RX-Z1 Owner's Manual

:_T¢][_ I',J IF,.\'d :Y,.Te._
• Normal stereo reproduction
<On the front panel>
Press STEREO/EFFECT to turn off the sound effect fbr normal
stereo reproduction.
<On the remote control>
Press the right button (labeled "STEREO") while any of the
RECEIVER control panel is displayed to turn off the sound effect
for normal stereo reproduction.
STEREO
!
1,,-,,i- r,- r,,i r,- :,,,i
2) i i:;" r=:, i::- t ,._
i% "i" :..... 1" ." "'= ." i r" r"
L. = i 2) .,,) ." .,::." L.r" i:;-
• If you turn off the sound effect, no sound is output from the center
speaker, rear speakers, rear center speaker and front effect
speakers.
• If you turn off the sound effect while a Dolby Digital or DTS
signal is being output, the dynamic range of the signal is automati-
cally compressed and the sounds of the center and rear speaker
channels are mixed and output from the main speakers.
• The volume may be greatly reduced when you turn off the sound
effect or if you set "12 DYNAMIC RANGE" on the SET MENU
to "MIN". In this case turn on the sound effect.
• Displaying the information about the input
source
During the stereo reproduction, information about the signal being
played back can be displayed by tapping @ or on the
PARAMETER control panel.
When "STEREO" is selected while Dolby Digital, DTS, or PCM
signals are being played, the fl_llowing infl_rmation will be shown
on the front panel display.
When Dolby Digital signals are played:
"Dolby D" + the number of channels (front/rear/LFE signal)
2) i i:::, r =:. i:2L._
r',, .., 'i i .... r',, ,"= ,, :"5 ,,
i,,. =LJ,i.i:,J":::_ i,,. = .,:D ." i:;j.. . ............
When DTS signals are played:
"DTS" + the number of channels (front/rear/LFE signal)
2) i i:2r=:. i:2t.._
r',, "i" :...... '.; ,, ,"= ,, i r" r
i..,= i 2) .,,) ." .,:; ." i... r" i:;;
When PCM signals are played:
"PCM" + sampling frequency
i" "i ° i" i"i i" i"i
,==i i:::r=:. i::" L J
i"1 i"" i,,'i ,'i i"= i , i i ....
r" L..i'i '..i. 0 i':.r"i,,:D
When analog signals are played:
2) i i:: Di'=:. i:: D LJ
i"_r i,::_,i.LJ '::_
,,o...
The three types of information shown below are displayed as
switched every time is tapped.
fs: "unknown" is displayed when the sampling frequency for the
input signal is not known.
i" "i" r"* r"i r"* i'i
,:) i i::: r=:, i ::: LJ
f: :iii. : :4 E:i:: i i z
rate: "unknown" is displayed when the bit rate of the input signal is
not known.
i,.- ,.i- i,,- i,,.i i,,- i,,.i
,:) i i:::i'=:, i:::LJ
....... i.... 11 'i i"_i "% i"51 , i .........
r" .::_L. i ::._, ,i.2 .,:;i:;j i ':.i:,Ji"" ::::.
fig: "None"
is displayed when the flag contained in the input signal
to be used for signal process cannot be detected.
i" "i" r" r"i r" i'i
,::) i i=, r=:. i :2 LJ
T" .i. "::2, i172) i'i L. r'.:.:, i=_, .i.
E-49