Verifying The Status Of A Module; Checking The State Of A Module - HP Cisco MDS 9020 - Fabric Switch Configuration Manual

Verifying the Status of a Module

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
Verifying the Status of a Module
Before you begin configuring the switch, you need to ensure that the modules in the chassis are
functioning as designed. To verify the status of a module at any time issue the show module
command(see the
ready to be configured when the
output of the show module command follows:
switch# show module
Mod
---
2
4
5
6
8
9
Mod
---
2
5
6
8
9
Mod
---
2
5
6
8
9
* this terminal session
The Status column in the output should display an
standby (or HA-standby) status for supervisor modules. If the status is either ok or active, you can
continue with your configuration..
A standby supervisor module reflects the HA-standby status if the HA switchover mechanism is enabled
Note
(see the
enabled, the standby supervisor module reflects the standby status.
The states through which a switching module progresses is discussed in the
Module" section on page

Checking the State of a Module

If your chassis has more than one switching module (also known as line card), you can check the
progress by issuing the show module command several times and viewing the
The switching module goes through a testing and an initializing stage before displaying an
Table 11-3
Cisco MDS 9000 Family CLI Configuration Guide
11-4
"Fibre Channel Interfaces" section on page
Ports Module-Type
----- ------------------------------- ------------------ ------------
8 IP Storage Services Module
0 Caching Services Module
0 Supervisor/Fabric-1
0 Supervisor/Fabric-1
0 Caching Services Module
32 1/2 Gbps FC Module
Sw Hw World-Wide-Name(s) (WWN)
----------- ------ --------------------------------------------------
1.3(0.106a) 0.206 20:41:00:05:30:00:00:00 to 20:48:00:05:30:00:00:00
1.3(0.106a) 0.602 --
1.3(0.106a)) 0.602 --
1.3(0.106a) 0.702 --
1.3(0.106a) 0.3 22:01:00:05:30:00:00:00 to 22:20:00:05:30:00:00:00
MAC-Address(es)
--------------------------------------
00-05-30-00-9d-d2 to 00-05-30-00-9d-de
00-05-30-00-64-be to 00-05-30-00-64-c2
00-d0-97-38-b3-f9 to 00-d0-97-38-b3-fd
00-05-30-01-37-7a to 00-05-30-01-37-fe
00-05-30-00-2d-e2 to 00-05-30-00-2d-e6
"HA Switchover Characteristics" section on page
11-4.
describes the possible states in which a module can exist.
status is displayed in the show module command output. A sample
ok
Model
DS-X9308-SMIP
DS-X9530-SF1-K9
DS-X9530-SF1-K9
DS-X9560-SMAP
DS-X9032
<--------------- New running version in module 6
Serial-Num
----------
JAB064605a2
JAB06350B1R
JAB072705ja
JAB06280ae9
status for switching modules and an active or
ok
9-2). If the warm switchover mechanism is
Chapter 11 Managing Modules
12-1). The interfaces in each module are
Status
ok
ok
active *
ha-standby
ok
ok
"Checking the State of a
column each time.
Status
OL-16184-01, Cisco MDS SAN-OS Release 3.x
status.
ok