Configuring Terminal Parameters; Setting The Terminal Session Timeout - HP Cisco MDS 9020 - Fabric Switch Configuration Manual

Chapter 2 Before You Begin
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
switch# traceroute www.cisco.com
Tracing route to www.cisco.com [198.133.219.25] 30 hops max, 38 byte packets
1
2
3
4
5
6
7
8
9
10
11
12
13
The IPv6 syntax for this command is traceroute ipv6 host or traceroute ipv6 ipv6-address.
switch# traceroute ipv6
Target IPv6 address: 2001:0DB8::3/64
Datagram size [40]:
Extended commands [n]: y
Maximum time-to-live [30]:
Source address:
Port number [33434]:
To cancel a traceroute or traceroute ipv6 command before it completes, enter Ctrl-C.

Configuring Terminal Parameters

This section includes the following topics:
•
•
•
•
•
•

Setting the Terminal Session Timeout

Use the exec-timeout command in configuration mode to configure the lifetime of all terminal sessions
on that switch. When the time limit configured by this command is exceeded, the shell exits and closes
that session. The syntax for this command is exec-timeout minutes.
The default is 30 minutes. You can configure different timeout values for a console or a virtual terminal
line (VTY) session. You can set the exec-timeout value to 0 to disable this feature so the session remains
active until you exit the switch. This change is saved in the configuration file.
•
OL-16184-01, Cisco MDS SAN-OS Release 3.x
bras3-l0.pltnca.sbcglobal.net [151.164.184.79] 30 ms
dist2-vlan50.pltn13.pbi.net [64.164.97.67] 20 ms
bb2-g1-1.pltn13.pbi.net [67.116.251.194] 20 ms
bb1-p12-0.pltn13.pbi.net [151.164.40.17] 20 ms
bb2-p13-0.sntc01.pbi.net [151.164.191.65] 20 ms
ex1-p3-0.eqsjca.sbcglobal.net [64.161.1.54] 20 ms
sl-st20-sj-0-0.sprintlink.net [144.223.242.81] 20 ms
sl-bb25-sj-10-0.sprintlink.net [144.232.20.62] 20 ms
sl-gw11-sj-10-0.sprintlink.net [144.232.3.134] 70 ms
sl-ciscopsn2-11-0-0.sprintlink.net [144.228.44.14] 20 ms
sjce-dmzbb-gw1.cisco.com [128.107.239.89] 20 ms
sjck-dmzdc-gw1.cisco.com [128.107.224.69] 20 ms
www.cisco.com (198.133.219.25)
Setting the Terminal Session Timeout, page 2-17
Setting the Terminal Timeout, page 2-18
Setting the Terminal Type, page 2-19
Setting the Terminal Screen Length, page 2-19
Setting the Terminal Screen Width, page 2-19
Displaying Terminal Settings, page 2-19
From the console:
switch(config)# line console
switch(config-console)# exec-timeout 60
Specifies the current console shell timeout to be 60 minutes.
20 ms
20 ms
21 ms
20 ms
20 ms
30 ms
30 ms
2.496 ms * 2.135 ms
Cisco MDS 9000 Family CLI Configuration Guide
Configuring Terminal Parameters
30 ms 20 ms
30 ms
20 ms
20 ms
30 ms
30 ms
20 ms 30 ms
30 ms 20 ms
30 ms 30 ms
30 ms 20 ms
30 ms
20 ms
2-17