Page 1: User Guide
User Guide HP BladeSystem PC Blade Enclosure Integrated Administrator v4.20...
Page 2 © Copyright 2007, 2008 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows are trademarks of Microsoft Corporation in the U.S. and other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Page 3: About This Book
About This Book WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
Page 4 About This Book ENWW...
Page 5: Table Of Contents
Table of contents 1 About This Guide Audience Assumptions ......................... 1 Important Safety Information ........................ 1 Symbols on Equipment ........................1 Related Documents ..........................2 Getting Help ............................2 Contact HP .......................... 2 Support and Troubleshooting ....................2 HP Web Site ........................2 2 HP PC Blade Enclosure System Software Features HP PC Blade Enclosure Integrated Administrator ................
Page 6 Determining the IP Address Using the Local Console ............12 Setting Up the Web-Based User Interface ..................13 Additional Steps ..........................15 4 Web Browser Interface Accessing the Web-based User Interface ..................16 Web-Based Navigation ........................17 Top Panel .......................... 17 Left Panel ...........................
Page 7 6 Setting Up the System User Permissions ..........................72 Customizing the Enclosure Settings ....................73 Modifying Enclosure and Rack Names ................73 Modifying the Asset Tag Number ..................74 Modifying the Date and Time ..................... 75 Setting Up User Accounts ........................77 Adding a Group ........................
Page 8 Creating a Certificate Request ..................113 Downloading a Security Certificate .................. 113 Key-Based SSH Authentication ......................113 Configuring Blade PC Boot Order ....................114 Powering Off the Enclosure ......................115 Disabling Network Protocols ......................116 Upgrading the Integrated Administrator Firmware ................117 Recovering a Lost Administrator Password ..................
Page 9 Appendix J Open Source Availability Appendix K Supported SNMP Traps Index ................................. 150 ENWW...
Page 10 ENWW...
Page 11: About This Guide
About This Guide Audience Assumptions This guide is for the person who installs, administers, and troubleshoots HP Blade PC solutions. HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels. Important Safety Information WARNING! Before installing this product, read the Important Safety Information document included...
Page 12: Related Documents
WARNING: To reduce the risk of injury from electric shock, remove all power cords to completely disconnect power from the system. This symbol indicates that the component exceeds the recommended weight for one individual to handle safely. WARNING: To reduce the risk of personal injury or damage to the equipment, observe local occupational health and safety requirements and guidelines for manual material handling.
Page 13: Hp Pc Blade Enclosure System Software Features
HP PC Blade Enclosure System Software Features The HP BladeSystem offers an extensive set of features and optional tools to support effective blade PC management and software deployment. This chapter describes the HP PC Blade Enclosure Integrated Administrator and provides a brief overview of software associated with the system. HP PC Blade Enclosure Integrated Administrator The HP PC Blade Enclosure Integrated Administrator is a centralized management and monitoring system for the HP PC Blade Enclosure and blade PCs.
Page 14: Snmp Alerts From Integrated Administrator To A Management Console
SNMP Alerts from Integrated Administrator to a Management Console The Integrated Administrator provides notification of enclosure problems. Using a management console, you can access various alerts, such as unauthorized access attempts and network connection failures using SNMP traps. The CPQRACK.MIB file contains HP-specific SNMP Object Identifiers (OIDs) and traps for managing the enclosure infrastructure and blades.
Page 15: Automatic Network Configuration
The Integrated Administrator provides secure password encryption, tracking all login attempts and maintaining a record of all login failures. The Integrated Administrator also provides the following additional security features: ● User actions logged in the Integrated Administrator System Log ● Login legal warning IP Security allows an administrator to define a set of IP addresses that are the only ones allowed to connect to the services provided (SSH, HTTP, HTTPS, TELNET, SNMP).
Page 16: Integration With The Hp Systems Insight Manager Utility
Integration with the HP Systems Insight Manager Utility The Integrated Administrator provides full integration with the HP Systems Insight Manager utility under key operating environments. This integration provides: ● Support for SNMP management—Support for SNMP trap delivery to a HP Systems Insight Manager console ●...
Page 17: Event Notification
account that is provided for ease of implementing within a deployment that uses HP SAM. This account is disabled by default. Event Notification The Integrated Administrator provides real-time event notifications for an enclosure. When an event occurs, the Integrated Administrator notifies connected users by generating an icon that the user can click to view more details.
Page 18 You can configure both interfaces to require a valid user name and password for authentication. RMON (for the switch) and SNMP manageability are supported. You can also save the interconnect switch configuration to a TFTP server as backups and as templates for preconfiguring other switches. Chapter 2 HP PC Blade Enclosure System Software Features ENWW...
Page 19: Getting Started
Getting Started The HP PC Blade Enclosure Integrated Administrator enables monitoring and management of all functions within an enclosure, including functions specific to the blade PCs housed within it. Once configured, the Integrated Administrator provides these features through both a Web-based user interface and CLI.
Page 20: Identifying Integrated Administrator Components
Identifying Integrated Administrator Components Each HP PC Blade Enclosure interconnect tray ships with the Integrated Administrator module already installed and provides external connectivity using two connectors on the rear panel. Table 3-1 Integrated Administrator Rear Panel Components Item Description Management (10/100 Ethernet) connector for remote access through a Web-based user interface, Telnet, or Secure Shell.
Page 21: Requirements For Local Client Devices
Requirements for Local Client Devices You can access the Integrated Administrator locally using the serial connector on the rear panel of the enclosure using a local client device, such as a laptop computer. The local client device must run a terminal emulator, such as HyperTerminal for Windows systems or Kermit for Linux systems.
Page 22: Determining The Ip Address Using The Local Console
Determining the IP Address Using the Local Console To determine the Integrated Administrator IP address using the local console perform the following steps: Access the Integrated Administrator console: Connect a local client device (such as a laptop computer) with VT100 terminal emulation software to the Integrated Administrator (serial) console connector using a null modem serial cable.
Page 23: Setting Up The Web-Based User Interface
Setting Up the Web-Based User Interface To set up the Web-based user interface, proceed as follows: Type the Integrated Administrator IP address or DNS name in the address bar of the Web browser. A security alert displays as shown below. If you click Yes, the browser continues to the Login window of Integrated Administrator.
Page 24 The Account Login screen (shown below) prompts you for a user name and password. Use the default user name and password from the settings tag attached to the interconnect tray, and then click Log In. After the default user name and password have been verified, the summary window appears. The Integrated Administrator summary window provides general information about the Integrated Administrator, such as the user currently logged on, enclosure name and status, and Integrated Administrator IP address and name.
Page 25: Additional Steps
Additional Steps HP recommends performing the following tasks: ● Change the Administrator password ● Set the date and time ● Name the enclosure and rack ● Set up groups, users, and access privileges For detailed instructions on performing these tasks, see the appropriate sections in Setting Up the System on page ENWW...
Page 26: Web Browser Interface
Web Browser Interface This chapter provides information for navigating the Integrated Administrator Web-based user interface: NOTE: Values appearing in the screens of this chapter are for illustrative purposes only. Accessing the Web-based User Interface Accessing the Web-based user interface is not supported from the console (serial) connector. To access the Integrated Administrator Web-based user interface with HTTP: Get the DNS name from the settings tag attached to the interconnect tray.
Page 27: Web-Based Navigation
Web-Based Navigation The Web-based user interface displays information and receives input in the following areas: ● Top panel ● Left panel ● Deck panel Top Panel The following illustration shows the location of the top panel. The top panel information is displayed at all times, including the following items: ●...
Page 28: Deck Panel
The left panel displays which screens are available under each tab. Information appearing in the left panel depends on which tab the user chooses from within the top panel. Deck Panel The following illustration indicates the position of the deck panel. Chapter 4 Web Browser Interface ENWW...
Page 29: Enclosure Tab
The deck panel displays the areas of information provided by the available screens under each tab. Information appearing in the deck panel depends on the option chosen by the user from within the top panel and the left panel. Enclosure Tab The Enclosure tab provides access to the following screens: ●...
Page 30 The following illustration shows the information presented on the Enclosure Information screen (status area, one of six shown). The Enclosure Information screen enables an enclosure administrator to update the rack name, enclosure name, asset tag, time zone, date, and time, as well as observe the status and general information for every component in the enclosure.
Page 31 Table 4-1 Enclosure Information Field Descriptions—Status Area (continued) For the default rack name, see Factory Default Settings on page 138. Enclosure Status OK, Degraded, or Failed. Status of the enclosure. Fan Status Redundant or non-redundant. Redundant: all fans are functional. Non- redundant: at least one fan is not functional.
Page 32 Table 4-3 Enclosure Information Field Descriptions—General Area (continued) Interconnect Tray Spare Number Spare number for the interconnect tray. Interconnect Tray Serial Number Serial number for the interconnect tray. Table 4-4 Enclosure Information Field Descriptions—Integrated Administrator Area Field Possible Values Description Integrated Administrator Area Hardware Version Hardware version of the Integrated...
Page 33: Network Configuration
Only enclosure administrators have access to the Date and Time information. If those fields are not being modified, the Integrated Administrator updates these fields every 20 seconds. If automatic time configuration is enabled, the date and time fields are grayed out and cannot be modified. If you select Other for time zone, use the following window to set a user-defined time zone: Three buttons appear on this window: ●...
Page 34 Two buttons appear at the bottom of this screen: ● Apply—Saves changes made to the screen. ● Cancel—Restores all fields on the screen to their original values. CAUTION: Both the Web and Secure Shell protocols must be enabled to allow access to the Web- based user interface.
Page 35: Snmp Configuration
Table 4-8 Network Configuration Field Descriptions—Protocols Area (continued) SNMP Enabled or Disabled. The default setting is Enabled. Secure Shell Enabled or Disabled. The default setting is Enabled. Telnet Enabled or Disabled. The default setting is Enabled. SOAP Enabled or Disabled. The default setting is Disabled.
Page 36 The following table describes the information presented on the SNMP Configuration screen: Table 4-10 SNMP Configuration Field Descriptions—System Information Area Field Possible Values Description System Information Area SNMP Status Enabled or Disabled Displays if SNMP is enabled or disabled. System Name The name of the enclosure.
Page 37: Power Readings
Table 4-11 SNMP Configuration Field Descriptions—Community Strings and Trap Destinations Area (continued) For the default read Community string, Factory Default Settings on page 138. Write Community Up to 20 characters including all Sets the SNMP write community string alphanumeric, dash, underscore, and If this is left blank, SNMP SET space characters commands are disabled.
Page 38: Virtual Buttons
● Enclosure Average Supply Input Power—The immediate average power consumption averaged over the last 5 second sample interval. ● Enclosure Average Supply Input Power 24-Hour Sample Intervals—This is a rolling average of power consumption over the course of preceding last 24 hours of uptime. ●...
Page 39: System Log
The Toggle On/Toggle Off button remotely changes the state of the enclosure Unit Identification LED. The illustration below shows the information presented in the Enclosure Power area of the Virtual Buttons screen: You can select the appropriate function with the following buttons: ●...
Page 40: System Log Policy
System Log Policy The System Log Policy screen (shown below) provides an enclosure administrator with display and control over the logging of some system logged event messages. There are two radio buttons for each event severity classification corresponding to enclosure and bay system log policies: ●...
Page 41: Bays Tab
Bays Tab The Bays tab provides access to the following screens: ● Bay List ● Bay Information ● Remote Console ● Virtual Buttons ● Console Log ● Bay Power Consumption Bay List The Bay List screen (shown below) enables an enclosure administrator to observe and update the assignment of groups to blade PC bays, as well as monitor the status of each blade PC installed in the enclosure.
Page 42: Bay Information
Table 4-12 Bay List Field Descriptions Field Possible Values Description Bay # 1-20 Blade PC number. Displays a blue circle if the unit identification (UID) LED of the blade is lit. Blade PC Name Name of the blade PC in that blade PC bay as defined by the operating system of the blade PC.
Page 43 To be sure that the Bay Information screen displays the optimal number of possible values, you must have the blade PC health driver installed. The following table describes the information presented on the Bay Information screen for all enclosure administrators and for group members and groups with rights to the blade PC bay. Table 4-14 Bay Information Field Descriptions—Status Area Field...
Page 44: Remote Console
Table 4-14 Bay Information Field Descriptions—Status Area (continued) Thermal Condition OK, Warm, Caution, or Critical Thermal condition of the blade. NOTE: In the case of a thermal critical or caution condition, BC2x00 blades provide thermal measurements for the CPU, Graphics processor, and ambient sensors in degrees Celsius at the time of failure detection.
Page 45: Virtual Buttons
For information on establishing remote console connectivity, see Enabling Remote Console Sessions to Blade PCs on page Virtual Buttons Enclosure administrators and group administrators with permissions can use the Virtual Buttons screen (shown below) to modify the state of the power state and Unit Identification LED of a blade PC in order to facilitate troubleshooting from a remote location.
Page 46 The Virtual Buttons screen enables group administrators and enclosure administrators to reboot, power off, or identify the blade PC with the following items: ● The Toggle On/Off button remotely changes the state of the blade PC Unit Identification LED. ● You can select the appropriate function in the Blade PC Power area using the following radio buttons: ◦...
Page 47: Console Log
Console Log NOTE: Only group members, group administrators, and enclosure administrators can view a console log of a blade PC. The Console Log screen displays the console log for the specified bay. The console log of the bay is not stored between reboots of the Integrated Administrator, so the information will only include what has taken place since the last power on of the Integrated Administrator.
Page 48 ● Wdc (24hr Avg.)—This is direct current (DC) power consumption in Watts of the blade averaged over the last 24 hours of operation within the enclosure. ● Wdc (Overall Avg.)—This is direct current (DC) power consumption in Watts of the blade averaged over the last 24 hours of operation within the enclosure.
Page 49: Administration Tab
Administration Tab For an explanation of user rights associated with the Integrated Administrator, see Enabling Remote Console Sessions to Blade PCs on page The Administration tab provides access to the following screens: ● User List ● Group List ● Add User ●...
Page 50: Group List
Table 4-17 User List Field Descriptions (continued) User Name User login name. Full Name User full name. Account Type Administrator or User Shows if the user is an enclosure administrator. Account Status Enabled or Disabled Shows if the user’s account is enabled. Group Membership Shows the groups in which the user has membership.
Page 51: Add User
Table 4-18 Group List Field Descriptions (continued) Assigned Bays Blade PC bays that the group owns Group Members Users with membership in the group Add User NOTE: Only enclosure administrators have access to this area of the Integrated Administrator. The Add User screen (shown below) enables an enclosure administrator to create a user profile, including group and blade PC bays assignments.
Page 52: Add Group
Table 4-19 Add User Field Descriptions (continued) The user name must begin with a letter. NOTE: “Administrator,” switch,” A maximum of 25 users can be created switcha, ”switchb,” “SAM,” and “all” are in addition to the reserve accounts. reserved names and cannot be used. This restriction is not case-sensitive.
Page 53 NOTE: Grayed-out check boxes are unavailable because they are already assigned to another group. Two buttons appear on this screen: ● Apply—Saves changes made to this screen. ● Cancel—Restores all fields on this screen to their original values. Table 4-20 Add Group Field Descriptions—Group Information Area Field Possible Values...
Page 54: View/Modify User
Table 4-21 Add Group Field Descriptions—Bay Assignment Area (continued) Bay 1 - Bay 20 Determines which bays the group owns. Only one group can own a particular bay. If a check box is disabled, another group already owns the bay. Select All Selects all check boxes of the bays.
Page 55: Event List Tab
Event List Tab The Event List tab provides access to the following screens: ● Event List ● Event Log Policy The Event List differs from the System Log in the following ways: ● Any user can view the Event List. Only enclosure administrators can access the System Log. ●...
Page 56: Event Log Policy
regarding the Event List, including a comprehensive list of event messages, see Event Icons and Details on page 136. Table 4-23 Event Notification Icons Icon Description Caution—An event that does not prevent the enclosure from operating, maintaining power, or serving its user community When a caution event occurs, a reasonable guarantee that operability can persist no longer exists.
Page 57: Interconnect Tab
For details concerning specific event log messages, see Error Messages on page 122 for supported event log messages and severity classification. Interconnect Tab The Interconnect Tray screen (shown below) allows anyone to view information about the interconnect tray. It allows enclosure administrators to connect to the remote console of one of the interconnect switches if installed.
Page 58 Table 4-24 Interconnect Tray Screen Field Descriptions—Interconnect Tray Information Area (continued) Manufacturer Manufacturer of the interconnect tray. Product Name Product name of the interconnect tray. Interconnect Tray Part Number Spare part number of the interconnect tray. Interconnect Tray Serial Number Serial number of the interconnect tray.
Page 59: Command Line Interface
Command Line Interface This chapter provides reference material for operating the Integrated Administrator Command Line Interface (CLI). This chapter provides command line related information with the following sections: ● Accessing the Command Line Interface ● Operating the Command Line Interface ◦...
Page 60: Accessing The Command Line Interface
Accessing the Command Line Interface You can access the CLI remotely through the management (10/100 Ethernet) connector, locally through the console (serial) connector on the rear panel of the enclosure, or through any uplink depending on VLAN configuration. Accessing Remotely through the Management Connector To access the Integrated Administrator command line interface remotely through the management (10/100 Ethernet) connector: Get the default host name from the settings tag attached to the interconnect tray.
Page 61: Operating The Command Line Interface
Operating the Command Line Interface General Commands The following table describes the information displayed in the areas that comprise the Enclosure Information screen. Table 5-1 General Commands Command Description Restrictions CLEAR SCREEN Clears the terminal screen None EXIT Exits the command line interpreter None HELP {<ommand>} |Tree If a command is given, the usage and help text for the...
Page 62 Table 5-2 General Management Commands (continued) DOWNLOAD SSHKEY Downloads an authorized key file to use with Secure Shell v2, Only enclosure administrators which can contain the public keys for any enclosure may execute this command. administrator. Supported protocols are http, ftp, and tftp. Format the URL as protocol://host/path/file.
Page 63: User Account Commands
Table 5-2 General Management Commands (continued) SHOW ENCLOSURE Display power consumption estimates for the enclosure, This command provides only POWER including all sub-components. This information includes estimated power usage based overall power consumption of the enclosure, as well as peak on measurements reported power and time averaged power across a 24-hr-and-since from power-aware blades and...
Page 64 Table 5-3 User Account Commands (continued) include alphanumeric, dash, and underscore characters. It must begin with a letter. NOTE: “Administrator,” switch,” switcha, ”switchb,” “SAM,” and “all” are reserved names and cannot be used. This restriction is not case- sensitive. Factory Default Settings on page 138 for factory default groups accounts.
Page 65 Table 5-3 User Account Commands (continued) DISABLE USER Disables a user account. Only enclosure administrators may execute this command. <user name> The user is immediately logged out of the system and prevented from log in until the account us enabled. The <user name>...
Page 66 Table 5-3 User Account Commands (continued) SET USER CONTACT If no <user name> exists, the command modifies the contact Only enclosure administrators info of the user that executed the command. may modify another user’s {<user name>} <contact info> contact information. The <user name>...
Page 67: Enclosure Network Configuration Commands
Table 5-3 User Account Commands (continued) permissions only see their user information. UNASSIGN ADMINSTRA- Takes enclosure administrator rights from a user. Only enclosure administrators TOR (RIGHTS) may execute this command. The Administrator account <user name> cannot have enclosure administrator rights taken away.
Page 68 (continued) Event Icons and Details on page 136 for supported SOAP commands. DISABLE SOAP Disables SOAP support for the Integrated Administrator for all This does not affect the built- administrator accounts. in SAM user account. See Event Icons and Details on page 136 for supported SOAP commands.
Page 69: Enclosure Management Commands
(continued) name is public. The default write community name is blank. SET SNMP CONTACT Configures the name of the system contact. Only enclosure administrators may execute <contact> this command. The <contact> must be 1-20 characters long and can include alphanumeric, dash, underscore, and space characters.
Page 70 (continued) SET DATE Sets the date of the enclosure with the following definitions: Only enclosure administrators may execute this command. ● MMDDhhmm MM: month ● MM is an integer from ● {{CC}YY} {TZ} DD: day 1-12 ● hh: hour (24-hour format) ●...
Page 71 (continued) SHOW DATE Displays the current date, time, and time zone of the internal None clock of the enclosure. SHOW DISPLAY Displays whether event notification is on or off. None SHOW ENCLOSURE FAN Displays the status, redundancy, and partner, speed, part None number for the requested fan.
Page 72: Blade Pc Bay Management Commands
(continued) pathname of the flash image to download UPLOAD CONFIG Upload the current runtime configuration to the specified FTP Only enclosure administrators or TFTP server. may execute this command. <url> For system log severity policy specific settings, these are global and set by the administrator account only. These were added to provide granular control over a specific classification of system log message severity types.
Page 73 (continued) NOTE: The blade’s specific operating system must support the NMI ‘crash dump’ feature or unpredictable results could occur on the blade. Please consult with your specific OS documentation or vendor for details. POWEROFF BAY Performs a graceful shutdown of the blade PC in the specified Only enclosure and group bay.
Page 74: Command Line Event Messages
(continued) future versions will support this feature. Earlier versions are indicated by (N/A). If no blade PC is in the bay, the user is shown the assigned to group and the blade PC type. SHOW BAY LIST [ALL | Displays the assigned to group, remote console user, and Group members and group <group name>] blade PC name for each bay in a particular group if a group...
Page 75 Table 5-7 Command Line Event Messages (continued) User Event Messages User Permission Change One of the following has occurred: ● A user has been added, removed, or modified. ● A user’s group membership has been modified. The blade PC bay membership has been changed for a group with at least one user.
Page 76 Table 5-7 Command Line Event Messages (continued) For BC2x00 blades, a diagnostic string accompanies the event message. See Error Messages on page 122 possible diagnostic strings and their descriptions. ● Blade in bay # has powered off. ● Blade in bay # has powered on. ●...
Page 77: Functionality Exclusive To The Command Line Interface
Functionality Exclusive to the Command Line Interface The following table identifies functions or capabilities available to the Command Line Interface (CLI) and unavailable when using the Web-based interface. Table 5-8 Functions Exclusive to the Command Line Interface—General and General Management Commands Function Description...
Page 78 Table 5-8 Functions Exclusive to the Command Line Interface—General and General Management Commands (continued) The password of the Administrator account does not change. The Integrated Administrator is restarted after all the changes are made. NOTE: This command removes all groups, users, and other customization from the memory of the enclosure, and the information is unrecoverable.
Page 79 Table 5-9 Functions Exclusive to the Command Line Interface—Enclosure Management Commands (continued) (measured in Hertz), part number, serial number, and hardware number, and hardware revision for the specified power supply if one is specified or for revision. all power supplies if ALL is given. SHOW ENCLOSURE Under an enclosure status heading, this command displays the The command line adds the...
Page 80 Table 5-9 Functions Exclusive to the Command Line Interface—Enclosure Management Commands (continued) This command may require a firmware upgrade for the BIOS ROM of certain HP blade PCs. SHOW BAY LIST [ALL | Displays the assigned to group, remote console user, and The command line displays <group name>] blade PC name for each bay in a particular group if a group...
Page 81: Setting Up The System
Setting Up the System This chapter explains the levels of user rights recognized by the Integrated Administrator and provides detailed procedures to configure the management functions provided by the Integrated Administrator. ● Customizing the enclosure settings ◦ Changing the Administrator password ◦...
Page 82: User Permissions
◦ Enabling NTP ◦ Disabling NTP ● Configuring SNMP support ◦ Entering a community string ◦ Modifying the system location ◦ Modifying the system contact information ◦ Adding trap targets ◦ Removing trap targets For a detailed explanation of the command line conventions used in this document, see Command Line Conventions on page 121.
Page 83: Customizing The Enclosure Settings
Table 6-1 HP PC Blade Enclosure Integrated Administrator Permissions Levels (continued) Group Administrator User View/Modify Group administrators may manage blade PC bay data for groups in which they are administrators. Group administrators may view blade PC bay data for groups in which they are members. Group administrators may modify their profile (not their privileges) and view enclosure data.
Page 84: Modifying The Asset Tag Number
Type the rack name. Click Apply. To modify the enclosure name or rack name using the CLI, type the following commands sequentially: SET ENCLOSURE NAME <enclosure name> NOTE: The <enclosure name> must be 1-32 characters long and includes all alphanumeric, the dash, and the underscore characters.
Page 85: Modifying The Date And Time
Type the asset tag number. Click Apply. To modify the asset tag number using the CLI, type: SET ENCLOSURE ASSET {TAG} <asset tag> NOTE: The <asset tag> must be 1-31 characters long and includes alphanumeric, dash, and underscore characters. The default enclosure asset tag is blank. Modifying the Date and Time To modify the date and time settings using the Web-based user interface: Click the Enclosure tab.
Page 86 Type the date or time. Click Apply. To modify the date and time settings using the CLI, type: SET DATE MMDDhhmm{{CC}YY} {TZ} where: ● MM: month ● DD: day ● hh: hour (24-hour time, an integer from 0-23) ● mm: minute ●...
Page 87: Setting Up User Accounts
Setting Up User Accounts NOTE: Only enclosure administrators may perform this task. The Integrated Administrator enables you to manage blade PC bays and administer users by organizing those blade PC bays and users into groups. This approach enables enclosure administrators, for example, to re-assign user permissions to groups of blade PCs en masse, instead of requiring enclosure administrators to modify permissions one user at a time.
Page 88 Select bays for the group by selecting the appropriate check boxes. NOTE: If a blade PC bay is gray, that blade PC bay is inaccessible because it already belongs to another group. Chapter 6 Setting Up the System ENWW...
Page 89: Adding A User
To add existing users to this group: Select users in the User Names area. Click Add User [View] or Add User [View/Modify]. For more information on permission levels, see User Permissions on page 72 in this chapter. Click Apply. To create a group using the CLI, type the following commands sequentially: ADD GROUP <group name>...
Page 90 For information on permission levels, see User Permissions on page 72 in this chapter. To create a user using the Web-based user interface: Click the Administration tab. Click Add User in the left panel. Type the user information in the appropriate field. For information on “Account Type,” see User Permissions on page 72 in this chapter.
Page 91 To assign the user to an existing group: Select groups in the Group Names area. Click Add User [View] or Add User [View/Modify]. For more information on permission levels, see User Permissions on page 72 in this chapter. 5. Click Apply. To add a user using the CLI, type the following commands sequentially: ADD USER <user name>...
Page 92: Enabling Remote Console Sessions To Blade Pcs
NOTE: The <user name> must be unique to all other user names and group names and is case- sensitive. It must be 1-13 characters long and can include all alphanumeric characters, the dash, and the underscore. The <password> must be 3-8 characters long and includes all printable characters. ASSIGN ADMINISTRATOR {RIGHTS} <user name>...
Page 93: E-Mail Alerts
E-mail Alerts AlertMail, if enabled, will send out alerts by e-mail for the following events: ● Enclosure boot message ● IA reboot message ● Fan status change ● Fan inserted ● Fan removed ● Enclosure thermal status change ● Power supply status change ●...
Page 94: Setting Up Ip Security
----SAMPLE START---- Subject: HP AlertMail-010: (CRITICAL) Power Supply #1: Failed Date: Wed, 23 Apr 2003 15:02:22 +0200 From: Enclosure IA-00508BEBA571 <IA-00508BEBA571@hp.com> To: user@userdomain X-OS: HP Integrated Administrator X-Priority: 1 Content-Type: text/plain; charset=us-ascii EVENT (26 May 07:09): Power Supply #1 Status has changed to: Failed Enclosure, IA-00508BEBA571, has detected that a power supply in bay 1 has changed from status OK to Failed.
Page 95: Setting Up Automatic Time Configuration (Ntp)
Setting Up Automatic Time Configuration (NTP) Automatic time configuration allows the Integrated Administrator to synchronize its date and time with an NTP capable device supporting the Network Time Protocol (NTP). Table 6-4 Automatic Time Configuration Commands Function Command Set the NTPpoll interval* SET NTP POLL <seconds>...
Page 96: Configuring Snmp Support
Configuring SNMP Support NOTE: Only enclosure administrators may execute these tasks. Entering a Community String To enter a read community or write community string using the Web-based user interface: Click the Enclosure tab. Click SNMP Configuration in the left panel. Click the Read Community or Write Community field.
Page 97: Modifying The System Location
The default read community name is “public,” and the default write community name is blank. Modifying the System Location NOTE: The SNMP protocol can be disabled in the Network Configuration area of the Web-based user interface. To modify the system location information using the Web-based user interface: Click the Enclosure tab.
Page 98: Removing Trap Targets
The <IP address> must be in the form ###.###.###.###, where ### ranges from 0 to 255. The Integrated Administrator only supports v1 traps and directs the traps to SNMP port 162 by default. You can add a maximum of eight IP addresses to receive SNMP traps. Removing Trap Targets To remove a trap target list using the Web-based user interface: Click the Enclosure tab.
Page 99: Configuring Soap Support Tasks
Configuring SOAP Support Tasks Enabling SOAP Interface To enable the SOAP interface via the Web-based user interface: Click the Enclosure tab. Click Network Configuration in the left panel. Click the SOAP button to Enable Click Apply. To enable the SOAP interface via the CLI-based user interface, type: ENABLE SOAP Disabling SOAP Interface To disable the SOAP interface via the Web-based user interface:...
Page 100: Supported Soap Interface Commands
Supported SOAP Interface Commands The following table contains a summary of the supported SOAP interface commands a short description: Command Description userLogin Establishes a SOAP session with the IA for using SOAP interface web services. userLogout userLogout Closes a SOAP session with the IA. modifyPassword Change user account password via SOAP interface.
Page 101: Performing Common Administrative Tasks
Performing Common Administrative Tasks This chapter explains the following Integrated Administrator management functionalities: ● Managing blade PC bays ◦ Opening a remote console session to a blade PC ◦ Accessing ROM-Based Setup Utility for a blade PC ◦ Reviewing the activity for a blade PC ◦...
Page 102: Accessing The Rom-Based Setup Utility For A Blade Pc
To access the remote console using the Web-based user interface: Click the Bays tab. Click Bay List in the left panel. Select the blade PC from the blade list. NOTE: The blade PC name is listed in the column titled Blade Name. When a blade PC is highlighted, the Bay Information buttons become active.
Page 103 To access the ROM-Based Setup Utility (RBSU) for a blade PC using the Web-based user interface: Click the Bays tab. Click Bay List in the left panel. Select the bay from the bay list. Click Remote Console at the bottom of the screen. Click Remote Console from the Remote Console screen.
Page 104: Reviewing Activity For A Blade Pc
To exit RBSU: Press Esc. When prompted, press F10, press the key and the key to confirm. To close the remote console session: Press the Ctrl+Shift+_ keys. Press the key. Reviewing Activity for a Blade PC NOTE: This task can only be performed for a given blade PC bay by enclosure administrators, group administrators, and group members with access rights to the blade PC bay.
Page 105: Identifying A Blade Pc Using The Unit Identification Led
Click Reboot, Power Off or Power Off Immediately. Click Apply. When the blade PC power is off, the Power Off button text becomes Power On. To reboot the blade PC using the CLI, type: REBOOT BAY <bay number> {[ , | - ] <bay number>} {FORCE} {[PXE | HDD | RBSU]} NOTE: This command sends a request to the blade PC in a given bay to perform a graceful shutdown and then reboots the blade PC.
Page 106 To change the state of a Unit Identification LED of for a blade PC using the Web-based user interface: Click the Bays tab. Click Bay List in the left panel. Click the blade PC whose Unit Identification LED you wish to toggle. Click Virtual Buttons at the bottom of the screen.
Page 107: Managing The Enclosure
Managing the Enclosure Reviewing the Activity of the Enclosure The system log of the Integrated Administrator is a chronology of system activities, such as user logins, enclosure shutdowns, and system failures. The system log also displays warnings and errors that occur in the HP PC Blade Enclosure, including: ●...
Page 108 Click System Log in the left panel. To update the System Log, click Refresh. To clear the System Log, click Clear Log. The Integrated Administrator prompts you to confirm this decision. To view the System Log of the enclosure using the CLI, type: SHOW SYSLOG ENCLOSURE Only enclosure administrators can execute this command.
Page 109: Identifying The Enclosure Using The Unit Identification Led
Identifying the Enclosure Using the Unit Identification LED The virtual button for the Unit Identification LED of an enclosure physically changes the state of the Unit Identification LED on the rear panel of the enclosure from Off to On, or vice versa. The Unit Identification LED illuminates bright blue and is designed to help a technician quickly identify a specific enclosure in the data center.
Page 110 To generate a printable synopsis of all the data for the enclosure using the Web-based user interface, click Printable View in the top panel. The Web-based user interface opens a new window that shows all enclosure information, which you can copy and paste into a printable file. To obtain the enclosure information using the CLI, enter the following commands as needed: SHOW ENCLOSURE FAN [<fan number>...
Page 111: Identifying Problem Components
This command displays the location, status (OK, warm, degraded, or failed), and temperature (degrees Fahrenheit and Celsius) for all the temperature sensors of the enclosure. Identifying Problem Components The Integrated Administrator alerts you to problem conditions or failed components in the enclosure, such as: ●...
Page 112 Identify the degraded components in the enclosure and their respective part numbers in the following ways: ● Opening the enclosure system log ● Opening the event list - the event list differs from the system log in the following ways: ◦...
Page 113 To identify a degraded component using the event list from the Web-based user interface: Click the Event List tab. Click the degraded item in the event list. Click View Event Details at the bottom of the screen. This action opens the page in the Integrated Administrator that displays information about the degraded component.
Page 114 To identify a degraded component using the CLI: Type: SET DISPLAY EVENTS [BAY | ENCLOSURE | ON | OFF] to ON. Type: SET DISPLAY EVENTS ENCLOSURE ALL ON. Type: SET DISPLAY EVENTS BAY ALL ON. Type the appropriate commands: SHOW ENCLOSURE FAN [<fan number> | ALL] This command displays the status, redundancy, partner, speed, and part number for one or all fans in the enclosure.
Page 115: Managing Users
This command displays the status of enclosure health, Integrated Administrator health, and the Unit Identification LED under the heading “enclosure status,” and displays the status and capacity of the power supplies of the enclosure under the heading “power status.” SHOW ENCLOSURE TEMP This command displays the location, status (OK, warm, degraded, or failed), and temperature (degrees Fahrenheit or Celsius) for all the temperature sensors of the enclosure.
Page 116 Click Group List in the left panel. Click on the group whose rights you wish to modify. Click View/Modify Group. 106 Chapter 8 Performing Common Administrative Tasks ENWW...
Page 117: Disabling And Deleting User Accounts
Select the appropriate check boxes for the available blade PC bays that reflects the updated rights you wish to give the group. Click Apply. To modify rights to blade PC bays for an existing group using the CLI, choose from among the following commands: NOTE: Only enclosure administrators may execute these commands.
Page 118: Deleting A User Account
Click View/Modify User. Set the account status to Disabled. Click Apply. To disable a user account using the CLI, type: DISABLE USER <user name> When this command is executed, the user is immediately logged out of the system and prevented from logging in until the account is enabled.
Page 119: Deleting Group Accounts
Select the user account you wish to delete from the user list. Click Remove User. To delete a user account using the CLI, type: REMOVE USER [ALL | <user name>] If ALL is specified, the command deletes all the user accounts except the Administrator account. The Administrator account cannot be removed.
Page 120 Select the group from the group list. Click Remove Group. To delete a group account using the CLI, type: REMOVE GROUP [ALL | <group name>] If ALL is specified, the command deletes all the group accounts. 110 Chapter 8 Performing Common Administrative Tasks ENWW...
Page 121: Performing Advanced Functions
Performing Advanced Functions This chapter provides an explanation of the following advanced tasks you can perform using the Integrated Administrator. These procedures are supported by the Web-based user interface and the CLI unless otherwise noted: ● Replicating the configuration of the Integrated Administrator ●...
Page 122: Replicating The Configuration Of The Integrated Administrator
Replicating the Configuration of the Integrated Administrator NOTE: The Integrated Administrator does not support this task using the Web-based user interface. To set up several enclosures with the same configuration, configure one enclosure (such as add all user accounts, add all groups, and assign bays) and then replicate that configuration on the other enclosures. To replicate the configuration of the Integrated Administrator using the CLI: Login as Administrator on the first enclosure.
Page 123: Creating A Certificate Request
Creating a Certificate Request To create a security certificate using the CLI, type: GENERATE CERTIFICATE REQUEST This command generates a PKCS#10 certificate request. This certificate request can be sent to your certification authority (CA) to obtain a PKCS#7 certificate file to use below. To create a self-signed security certificate using the CLI, type: GENERATE CERTIFICATE SELFSIGNED This command generates a self-signed PKCS#7 certificate to replace the existing SSL certificate.
Page 124: Configuring Blade Pc Boot Order
This command downloads and install a file containing one or more SSH keys which are authorized to log into the Integrated Administrator. The new file will replace any existing keys. Supported protocols are http, ftp and tftp. Format the URL as: protocol://host/path/file. If your ftp server does not support anonymous logins, you can specify a username and password by replacing the host part (in previous format) with: username:password@host.
Page 125: Powering Off The Enclosure
The POWERON BAY and REBOOT BAY commands have been extended to allow an argument which sets blade PC boot order for that boot only. These settings are the same as the SET BAY BOOT ONCE command. To determine if any boot order changes are pending for a specific blade, use the SHOW BAY INFO command.
Page 126: Disabling Network Protocols
CAUTION: Without the blade PC health driver or an ACPI-compliant operating system, the Integrated Administrator cannot gracefully shutdown a blade PC. This condition may result in the permanent loss of critical data. Disabling Network Protocols To modify the supported communications protocols of the enclosure using the Web-based user interface: Click the Enclosure tab.
Page 127: Upgrading The Integrated Administrator Firmware
Disabling Secure Shell causes the users to lose access to the Web-based user interface. ● To disable telnet communication, type: DISABLE TELNET ● To disable the SOAP interface, type: DISABLE SOAP Upgrading the Integrated Administrator Firmware The firmware associated with the Integrated Administrator can be upgraded remotely using the CLI using the management (10/100 Ethernet) connector located on the rear panel of the enclosure.
Page 128: Launching Flash Disaster Recovery
Press and hold the enclosure Unit Identification button (1) and press the Integrated Administrator Reset button (2) simultaneously on the rear panel of the blade PC to place the enclosure in Lost Password/Flash Disaster Recovery mode. When the serial console prompt appears, press the key.
Page 129 You can manually place the Integrated Administrator in Flash Recovery mode: Connect a local client device to the Integrated Administrator (serial) console connector using the nullmodem serial cable (provided with the enclosure). See Requirements for Local Client Devices on page Press and hold the enclosure Unit Identification button (1) and press the Integrated Administrator Reset button (2) simultaneously on the rear panel of the blade PC to place the enclosure in Lost Password/Flash Disaster Recovery mode.
Page 130 The Integrated Administrator then downloads and verifies the ROM and updates the flash memory. NOTE: No timeout exists for obtaining a DHCP address. NOTE: If the ROM does not download properly or if the verification step fails, Flash Disaster Recovery mode restarts with another attempt to acquire a DHCP address.
Page 131: Appendix A Command Line Conventions
Command Line Conventions The following table lists the conventions used by the Command Line Interface (CLI). Table A-1 CLI Conventions Symbol Description <lower case> Denotes input to be keyed in UPPER CASE Denotes input to be keyed in as shown Denotes choices to be made where a choice is mandatory Denotes choices to be made where a choice is optional Separates input options...
Page 132: Appendix B Error Messages
Error Messages The messages provided in this appendix are divided into the following categories: ● Warning messages ● Error messages Warning Messages This section provides a comprehensive list of warning messages specific to the major components of the Integrated Administrator. These warning messages advise you that you have implemented a configuration change or prompt you to confirm whether you wish to proceed with your requested action.
Page 133: Blade Pc Warning Messages
Blade PC Warning Messages Table B-2 Blade PC Warning Messages Warning Message Cause This blade has been removed from the enclosure. The blade that is being viewed has been removed from the enclosure. This blade has been powered off. All open sessions will be closed. The current blade has been powered off.
Page 134: Error Messages
Error Messages Enclosure Error Messages Table B-4 Enclosure Error Messages Error Message Cause Valid Input The maximum number (8) of trap destinations has Attempting to add a 9th trap been reached. destination The trap destination of ###.###.###.### is already Attempting to add a duplicate trap on the list.
Page 135 Table B-6 Administration Error Messages (continued) The group name is blank. Please enter a valid Attempting to create a group with a name. blank group name The maximum number (20) of groups exists on the Attempting to create a 21st group system.
Page 136 Table B-6 Administration Error Messages (continued) Invalid e-mail address supplied. Address should be Attempting to enter an e-mail E-mail addresses formatted in user@domain.tld format. address that is not in the correct “user@domain.tld” and containing format. a maximum of 64 characters. E-mail address is too long.
Page 137 Blade PC Diagnostic Messages The IA produces a diagnostic string associated with a degraded or critical health event from the blade. The following table lists the possible diagnostic strings it produces upon detection of a blade health change condition. Not all blades models support this feature. See Models Supported column for specific model types.
Page 138: 128 Appendix C Blade Pc Diagnostic Messages
Blade Health Major Code Minor Code Diagnostic Message Models Supported State Degraded 6928 (6928) - POST under Recovery BIOS image BC2000 / BC2500 Critical (6906) - Embedded Network Controller B BC2000 / BC2500 Hardware Failure Detected Critical (6907) - System Embedded Network Controller A BC2000 / BC2500 Hardware Failure Detected Critical...
Page 139: Appendix D Maskable Enclosure System Log Messages
Maskable Enclosure System Log Messages The IA provides a method of masking system log messages from being posted in the system log messages based on severity classification. See system log policy CLI and GUI command details in the preceding sections. All critical enclosure messages are not mask-able as they represent catastrophic conditions that should not be prevented from logging to the system log.
Page 140 – System Overheating (Zone – – – – For location [bay], 0, Location [location], only BC2x00 Temperature [value] deg. C) displays the temperature value for the overheating component. Fans System Fans: Repaired – – – – – (Fan #) – System Fan Removed (Fan –...
Page 141: Appendix E Maskable Enclosure Event Messages
Maskable Enclosure Event Messages The IA provide a method of masking event messages from being displayed by the CLI during an active session based on severity classification. See event log policy CLI and GUI command details in the preceding sections. The policy settings are session resident only. All bay informational events are disabled by default and must be enabled.
Page 142 – Fan # Status has changed – – – – Value = Paired to: Degraded - {value} fan status (paired with Fan #) – Fan # Status has changed – – – – Value = Paired to: OK - {value} (paired with fan status Fan #) –...
Page 143 – Blade in bay # thermal state – – – – # = bay number has changed to: Caution – Blade in bay # thermal state – – – – # = bay number has changed to: Warm – Blade in bay # thermal state –...
Page 144: Appendix F Troubleshooting
Troubleshooting This appendix provides troubleshooting information for the Integrated Administrator that ships as part of the HP PC Blade Enclosure. Use it to find details about solving performance problems that may arise when viewing or managing enclosure, blade PC, or user information using the Integrated Administrator. For information on LEDS, switches, and troubleshooting information for the HP PC Blade Enclosure, refer to the HP PC Blade Enclosure Setup and Installation Guide.
Page 145 Table F-1 Integrated Administrator Troubleshooting (continued) My fans periodically increase speed and Fans perform a self-test for 60 seconds every 24 hours. then return to their normal speed. Although my username and my The Integrated Administrator supports up to 48 concurrent sessions. Be sure the password are valid, I am unable to log number of sessions has not reached this threshold and check with an enclosure into the Integrated Administrator.
Page 146: Appendix G Event Icons And Details
Event Icons and Details The Integrated Administrator provides real-time event notifications for an enclosure according to two categories: caution and critical. When an event occurs, the Integrated Administrator notifies the user by generating an icon that the user can click to view more details: Table G-1 Event Notification Icons Icon...
Page 147 Table G-2 Event Details (continued) Enclosure <date> <time> The enclosure temperature has exceeded the caution threshold. Blade in bay # <date> <time> Blade # is in a degraded state. Blade in bay # <date> <time> The temperature on blade # has exceeded the caution threshold.
Page 148: Appendix H Factory Default Settings
Factory Default Settings This appendix provides the factory default settings for the following components of the HP PC Blade Enclosure Integrated Administrator. ● Enclosure ● Users ● Groups ● Network ● Protocol Enclosure The following table provides the default values in the Integrated Administrator for fields related to the blade PC enclosure.
Page 149 If you are using HP BladeSystem PC Blade Switch, part number 243283-B21 or DW367A, the Integrated Administrator provides the following default users: ● Administrator ● switcha ● switchb ● SAM (HP Session Allocation Manager) NOTE: The “switcha” and “switchb” accounts are used when accessing the optionally installed interconnect switch console.
Page 150: Groups
Groups No default groups are in the Integrated Administrator. Network The Integrated Administrator ships with the following default values assigned: Table H-2 Default Enclosure Values Field Default Value DHCP Enabled Dynamic DNS Enabled Protocol The following table provides the default values in the Integrated Administrator for fields related to network interface protocols: Table H-3 Default Network Values...
Page 151: Universal
Time Zone Settings This appendix provides a comprehensive list of time zones supported by the HP PC Blade Enclosure Integrated Administrator. These time zones are organized into the following categories: ● Universal ● Africa ● Asia ● Europe ● Oceania ●...
Page 152: Africa
Africa The following table provides the African time zone settings supported by the Integrated Administrator. Table I-2 African Time Zone Values Africa:Abidjan Africa:Ceuta Africa:Lagos Africa:Niamey Africa:Accra Africa:Conakry Africa:Libreville Africa:Nouakchott Africa:Addis Ababa Africa:Dakar Africa:Lome Africa:Ouagadougou Africa:Algiers Africa:Dar_es_Salaam Africa:Luanda Africa:Porto-Novo Africa:Asmera Africa:Djibouti Africa:Lubumbashi Africa:Sao_Tome Africa:Bamako...
Page 153: Europe
Table I-3 Asian Time Zone Values (continued) Asia:Bishkek Asia:Kashgar Asia:Seoul Japan Asia:Brunei Asia:Katmandu Asia:Shanghai Mideast:Riyadh87 Asia:Calcutta Asia:Krasnoyarsk Asia:Singapore Mideast:Riyadh88 Asia:Chungking Asia:Kuala_Lumpur Asia:Taipei Mideast:Riyadh89 Asia:Colombo Asia:Kuching Asia:Tashkent Asia:Dacca Asia:Kuwait AsiaTbilisi: Asia:Damascus Asia:Macao Asia:Tehran Asia:Dhaka Asia:Magadan Asia:Tel_Aviv Singapore Asia:Dili Asia:Manila Asia:Thimbu Turkey Asia:Dubai Asia:Muscat Asia:Thimphu...
Page 154: Oceania
Oceania The following table provides the Oceanic time zone settings supported by the Integrated Administrator. Table I-5 Oceanic Time Zone Values Atlantic:Azores Australia:North Kwajalein Atlantic:Bermuda Australia:NSW Atlantic:Canary Australia:Perth NZ-CHAT Atlantic:Cape_Verde Australia:Queensland Pacific:Apia Atlantic:Faeroe Australia:South Pacific:Auckland Atlantic:Jan_Mayen Australia:Sydney Pacific:Chatham Atlantic:Madeira Australia:Tasmania Pacific:Easter Atlantic:Reykjavik Australia:Victoria...
Page 155: Polar
Polar The following table provides the polar time zone settings supported by the Integrated Administrator. Table I-6 Polar Time Zone Values Antarctica:Casey Antarctica:McMurdo Antarctica:Vostok Antarctica:Davis Antarctica:Palmer Antarctica:Longyearbyen Antarctica:DumontDUrville Antarctica:South_Pole Antarctica: Antarctica:Mawson Antarctica:Syowa Americas The following table provides the American time zone settings supported by the Integrated Administrator. Table I-7 American Time Zone Values America:Adak...
Page 156 Table I-7 American Time Zone Values (continued) America:Managua America:Recife Canada:Central America:Manaus America:Regina Canada:Eastern America:Martinique America:Rio_Branco Canada:East-Saskatchewan America:Mazatlan America:Rosario Canada:Mountain America:Mendoza America:Santiago Canada:Newfoundland America:Menominee America:Santo_Domingo Canada:Pacific America:Merida America:Sao_Paulo Canada:Saskatchewan America:Mexico_City America:Scoresbysund Canada:Yukon America:Miquelon America:Shiprock Chile:Continental America:Monterrey America:St_Johns Chile:EasterIsland America:Montevideo America:St_Kitts Cuba America:Montreal America:St_Lucia Jamaica...
Page 157 Open Source Availability The Integrated Administrator is based on embedded Linux and contains numerous Open Source components. In compliance with Open Source licensing, HP has made the source code of all Open Source components used available at the following URL: opensource.hp.com To locate the Integrated Administrator project, consult the list of all projects.
Page 158 Supported SNMP Traps The following table contains the supported SNMP traps: NOTE: Please consult HP SNMP MIB file CPQRACK.MIB version 1.8 for trap details. Table K-1 CPQRACK MIB Traps Supported Trap Name Description Severity State 22001 cpqRackNameChanged Rack name changed INFORMATIONAL OPERATIONAL 22002 cpqRackEnclosureNameChanged...
Page 159 Table K-1 CPQRACK MIB Traps Supported (continued) Trap Name Description Severity State 22017 cpqRackPowerSupplyInserted Rack power supply INFORMATIONAL OPERATIONAL inserted 22018 cpqRackPowerSubsystemNotRedundant Rack power MAJOR DEGRADED subsystem not redundant 22019 cpqRackPowerSubsystemLineVoltageProblem Rack power supply MAJOR DEGRADED input voltage problem 22020 cpqRackPowerSubsystemOverloadCondition Rack power MAJOR...
Page 160 Index Symbols/Numerics blade PC commands 51 802.1Q 7 activity 94 commands, CLI bay management blade PC bay commands 62 management 62 accessing bays 91 enclosure management 59 remotely 50 boot order 114 enclosure network ROM-Based Setup Utility 92 error messages 124 configuration 57 Web-based user interface 16 identifying 95...
Page 161 default encryption 4 HP Systems Insight Manager Web settings 138 entering a community string 86 site 6 values for the Integrated error messages HP Web site 2 Administrator 11 Administration 124 HTTP 140 deleting blade PC bay 124 hyperlinks 6 group accounts 109 enclosure 124 user accounts 107, 108...
Page 162 left panel 17 notification, event 7 replicating configuration 112 local console 12 notifications 4 reporting, power consumption 5 location, modifying system 87 NTP 5, 85, 140 requirements, local devices 11 number of users supported 4 reviewing Bays tab 37 blade PC activity 94 maskable messages 129 configuration tools and Oceania time zones 144...
Page 163 support and troubleshooting 2 deleting account 108 Support and Troubleshooting Web disabling and deleting site 2 account 107 supported users 4 list 39 symbols equipment 1 managing 105 system setting up account 77 contact information 87 supported 4 location 87 view/modify account 44 log 29 utilities...

This manual is also suitable for:

Bladesystem bc2500 - blade pc Bladesystem pc blade enclosure integrated administrator v4.20

HP BladeSystem bc2000 - Blade PC User Manual

1 About this Guide

2 HP PC Blade Enclosure System Software Features

3 Getting Started

4 Web Browser Interface

5 Command Line Interface

6 Setting up the System

7 Configuring SOAP Support Tasks

8 Performing Common Administrative Tasks

9 Performing Advanced Functions

Appendix A Command Line Conventions

Appendix B Error Messages

128 Appendix C Blade PC Diagnostic Messages

Appendix D Maskable Enclosure System Log Messages

Appendix E Maskable Enclosure Event Messages

Appendix F Troubleshooting

Appendix G Event Icons and Details

Appendix H Factory Default Settings

Appendix I Time Zone Settings

Quick Links

User Guide

Troubleshooting

Related Manuals for HP BladeSystem bc2000 - Blade PC

Summary of Contents for HP BladeSystem bc2000 - Blade PC

This manual is also suitable for:

Table of Contents