Maximum Deflection in horizontal Mounting Position ..............20 5.4.1 SM01-37Sx60 ..........................20 5.4.2 SM01-37Sx60_BE01 ........................20 5.4.3 SM01-37Sx120 ..........................21 5.4.4 SM01-37Sx120_BE01 ......................... 21 Electrical Connection ..........................22 Motor Cable ............................. 22 Page 2 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Page 3
8.2.2 Mounting ............................29 Guide Shafts ............................ 33 8.3.1 Guide Shafts for SM01-37 Linear Modules with Linear Ball Bearing .......... 33 8.3.2 Guide Shafts for SM01-48 Linear Modules with Linear Ball Bearing .......... 34 8.3.3 Guide Shafts for SM01-37 Linear Modules with Plain Bearings ..........34 8.3.4...
Page 4
Back Plate ..........................62 12.8.3 Guide Block ..........................62 12.9 Linear Modules SM01-48x150_SSCP ..................... 63 12.9.1 Front Plate ..........................63 12.9.2 Back Plate ..........................63 12.9.3 Guide Block ..........................64 Page 4 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Page 5
Back Plate ..........................76 12.16.3 Guide Block ..........................77 13 International Certificates ........................77 14 EU Declaration of Conformity CE-Marking ..................83 15 UK Declaration of Conformity UKCA-Marking ..................84 NTI AG / LinMot SM01-37 / SM01-48 Page 5 / 85...
1.4 Liability NTI AG (as manufacturer of LinMot and MagSpring products) excludes all liability for damages and expenses caused by incorrect use of the products. This also applies to false applications, which are caused by NTI AG's own data and notes, for example in the course of sales, support or application activities.
Before working, make sure that there are no high voltages. Fast-moving Machine Parts The sliders of LinMot linear motors are fast-moving machine parts. All necessary precautions must be taken to prevent persons approaching the moving elements during operation (provide covers, guards, etc.).
Page 8
Linear motor sliders consist of a high-precision, thin-walled stainless steel tube in which the neodymium magnets are housed. The LinMot sliders should be handled with care. Avoid contact with other sliders or iron parts as this can damage the magnets and the slider surface.
In this case, the use of the fits with dowel pins should be avoided. For vertical mounting, the MagSpring® vertical load compensation is recommended. See chap. 4.3 NTI AG / LinMot SM01-37 / SM01-48 Page 9 / 85...
• Do not mount, hold or lift the SM01 on the MagSpring. Increased forces on the MagSpring stator may deform the mounting component and affect alignment. Page 10 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
This is ensured by the built-in sleeve. With each assembly, make sure to reinstall the sleeve so that the slider can be moved sideways! Sleeve NTI AG / LinMot SM01-37 / SM01-48 Page 11 / 85...
Installation Guide Linear Modules 4.5 Combinations SM01 linear modules can be screwed directly together using the LinMot mounting kit (see chapter 9.3) and, depending on the combination, the adapter plate (see chapter 9.4). Thus, any YZ combinations, as shown below, can be realised. In addition, a classic pillar system (see chapter 9.5) is available, with which the units can be flexibly adjusted in height if required.
The maximum load depends on the cantilever extension (distance H plus distance between the center of gravity of the working load and the mounting surface). 5.1.1 SM01-37Sx60 Cantilever extension [mm] 5.1.2 SM01-37Sx60_BE01 Cantilever extension [mm] Page 14 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
The maximum load depends on the cantilever extension (distance H plus distance between the center of gravity of the working load and the mounting surface). 5.2.1 SM01-37Sx60 Cantilever extension [mm] 5.2.2 SM01-37Sx60_BE01 Cantilever extension [mm] Page 16 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Cantilever extension [mm] For SM01 modules with plain bearings, please note that in addition to the load-dependent deflection, there is also a change in position due to the bearing clearance. Page 18 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Cantilever extension [mm] For SM01 modules with plain bearings, please note that in addition to the load-dependent deflection, there is also a change in position due to the bearing clearance. NTI AG / LinMot SM01-37 / SM01-48 Page 19 / 85...
Cantilever extension [mm] For SM01 modules with plain bearings, please note that in addition to the load-dependent deflection, there is also a change in position due to the bearing clearance. Page 20 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Cantilever extension [mm] For SM01 modules with plain bearings, please note that in addition to the load-dependent deflection, there is also a change in position due to the bearing clearance. NTI AG / LinMot SM01-37 / SM01-48 Page 21 / 85...
6.1 Motor Cable Do not connect or disconnect motor when there is power on the servo drive. Use only double-shielded original LinMot cable. Cables from other sources must be checked precisely before commissioning. Incorrect connections can destroy the drive and stator.
6.2.3 Pin Assignment Linear Modules SM01-37 Do not connect or disconnect motor when there is power on the servo drive. Use only double-shielded original LinMot cable. Cables from other sources must be checked precisely before commissioning. Incorrect connections can destroy the drive and stator.
6.2.4 Pin Assignment Linear Modules SM01-48 Do not connect or disconnect motor when there is power on the servo drive. Use only double-shielded original LinMot cable. Cables from other sources must be checked precisely before commissioning. Incorrect connections can destroy the drive and stator.
7 Start-up 7.1 Plug and Play LinMot SM01 linear modules are "Plug and Play" capable (see motor label "PnP"). This means that they log on to the drive independently. The module- and motor-specific parameters are automatically stored in the drive, and the motor is ready for operation.
UH1 approval). The replacement interval of the bearings is determined by the function test of the linear guide. See chapter 10.1. 8.1.1 Ordering Information All 4 linear ball bearings with the 4 associated seals should be replaced per linear module. For Linear Modules SM01-37 Item Description Item-No.
Page 27
(2) After that, there is approx. 5 mm space left to insert the seals. The bearings are already initially lubricated. NTI AG / LinMot SM01-37 / SM01-48 Page 27 / 85...
Page 28
7. Insert bearing tube and mount tube support (1) Push the bearing tubes into both tube supports. (2) Screw on the tube support. Apply Loctite 243 threadlocker to these screws. Tightening torque for SM01-37: 4.2 Nm Tightening torque for SM01-48: 7.4 Nm 8. Insert guide shafts The guide shafts are reinserted together with the back plate on the side without connector.
All 4 plain bearings should be replaced per linear module. Item Description Item-No. GL-A-2023-30 Plain bearings for the food sector 20x23-30 for SM01-37 Linear Modules 0160-3163 GL-A-3034-30 Plain bearings for the food sector 30x34x30 for SM01-48 Linear Modules 0160-3162 8.2.2 Mounting Be sure to observe the safety instructions in chapter 2 during assembly! 1.
Page 30
Kukko 27-A. 5. Insert new plain bearings The new bearings are inserted as far as they will go with the help of a hand press or a press pin. Page 30 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Page 31
When handling with sliders, there are sometimes large magnetic forces of attraction. Observe the warnings in chapter 2! If necessary, cover nearby iron constructions with non-magnetic material (e.g. wood). NTI AG / LinMot SM01-37 / SM01-48 Page 31 / 85...
Page 32
The front plate must be positioned on the side of the connector and the rear plate on the opposite side. The installation positions of the mounting plates must not be interchanged! Page 32 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Stainless steel or hard-chrome plated shafts ensure precise guidance. As a rule, these do not need to be replaced. Only in case of damage should the guide shafts be replaced. 8.3.1 Guide Shafts for SM01-37 Linear Modules with Linear Ball Bearing Item Description Item-No.
SL01-25-15.6x790-M8 Guide shaft, hollow, hard chrome plated, L= 790 mm for 0150-4460 SM01-48x150, Stroke = 555 mm SM01-48x240, Stroke = 465 mm 8.3.3 Guide Shafts for SM01-37 Linear Modules with Plain Bearings Item Description Item-No. SL01-20-16x223-SSC-HIS Guide shaft, hollow, SSC, hardened, L= 223 mm for...
Clamp the guide unit and loosen the screws of the guide shafts on the back plate completely. Mark the "top" and "bottom" of the back plate so that it can be reinstalled exactly the same. NTI AG / LinMot SM01-37 / SM01-48 Page 35 / 85...
Page 36
(1) Push the back plate to the stop of the guide block. (2) Tighten the screws firmly. Tightening torque: 18 Nm If the guide does not move smoothly, loosen the screws again and repeat this step. Page 36 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
1. Slide the front plate to the stop of the guide block. 2. Dismantle the front plate Loosen the screws of the guide shafts and the slider and remove the plate. NTI AG / LinMot SM01-37 / SM01-48 Page 37 / 85...
These must be reinstalled when replacing the back plate. The "slot hole" labelling on the back plate must be on the same side as the front plate. Page 38 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
The mounting kit contains all necessary screws to mount the SM01 linear modules together. The mounting combination of the SM01 linear modules are as follows: • SM01-37 on SM01-37 (mounting kit required) • SM01-37x120 on SM01-48x (mounting kit required) •...
Pillar System To realize a YZ combination of the SM01 linear modules, LinMot offers a mounting kit for screwing the modules together as well as a classic pillar system with which the units can be flexibly adjusted in height if required.
2 pieces each of position 1, 2 and 3 must be ordered. • If two SM01 linear modules are to be screwed together, the assembly kit "Z01-AsKit- SM01-SM01" ( 0150-4507) can be ordered. It contains all the necessary screws. Item-No. NTI AG / LinMot SM01-37 / SM01-48 Page 43 / 85...
However, lubrication of the bearings is recommended and also prescribed in certain load cases (see chapter 10.3.1). In lubricated operation, cleaning is carried out as follows: Page 44 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Relubrication is carried out according to the following instructions: • Remove the old grease from the guide shafts with a soft cleaning cloth or paper towel. If necessary, use a grease-dissolving agent (e.g. petroleum ether). NTI AG / LinMot SM01-37 / SM01-48 Page 45 / 85...
See chapter “EU Declaration of Conformity CE-Marking” See chapter “UK Declaration of Conformity UKCA-Marking” IECEE Ref. Certif. Nr. CH-8521 CB SCHEME USA / Canada File Number E354430 Refers to cURus marked motors NTI AG / LinMot SM01-37 / SM01-48 Page 77 / 85...
Page 78
Installation Guide Linear Modules Page 78 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Page 79
Installation Guide Linear Modules NTI AG / LinMot SM01-37 / SM01-48 Page 79 / 85...
Page 80
Installation Guide Linear Modules Page 80 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Page 81
Installation Guide Linear Modules NTI AG / LinMot SM01-37 / SM01-48 Page 81 / 85...
Page 82
Installation Guide Linear Modules Page 82 / 85 SM01-37 / SM01-48 NTI AG / LinMot...
Installation Guide Linear Modules 14 EU Declaration of Conformity CE-Marking NTI AG / LinMot ® Bodenaeckerstrasse 2 8957 Spreitenbach Switzerland Tel.: +41 (0)56 419 91 91 Fax: +41 (0)56 419 91 92 declares under sole responsibility the compliance of the products: •...
Installation Guide Linear Modules 15 UK Declaration of Conformity UKCA-Marking NTI AG / LinMot ® Bodenaeckerstrasse 2 8957 Spreitenbach Switzerland Tel.: +41 (0)56 419 91 91 Fax: +41 (0)56 419 91 92 declares under sole responsibility the compliance of the products: •...
Page 85
ALL LINEAR MOTION FROM A SINGLE SOURCE Europe / Asia Headquarters North / South America Headquarters NTI AG - LinMot & MagSpring LinMot USA Inc. Bodenaeckerstrasse 2 N1922 State Road 120, Unit 1 CH-8957 Spreitenbach Lake Geneva, WI 53147 Switzerland Sales / Administration: +41 56 419 91 91 Sales / Administration: 262.743.2555...