Adding Custom Words - ADEMCO Via 30+ Installation Instructions Manual

Table of Contents

Advertisement

IN STEPS
3-5,
THE
CONSOLE
KEYS
PERFORM
THE
FOLLOWING
FUNCTIONS
{3] Advances through alphabet
and actual words in alpha-
betical order.
Moves
backward
through
alphabet and actual words
in alphabetical order.
Toggles between alphabet
and actual word list; used to
accept entries.
Saves the zone description
in the system's memory.
[1]
[6]
[8]
Adding
Custom
Words
(will not be annunciated
by 4285 Volce Module)
IN STEPS
3-6,
THE
CONSOLE
KEYS
PERFORM
THE
FOLLOWING
FUNCTIONS
[3] Advances through alpha-
bet, symbols, and numbers.
Moves
backward
through
alphabet,
symbols.
(1]
numbers
and
Selects
desired
letter;
moves cursor one space to
right.
Moves cursor one space to
left.
Inserts a space at the cur-
sor location,
erasing any
character located there.
Saves the new word in the
system's memory.
b) Select the first letter of the desired description
(note that "A"
is already displayed). Press key [3] repeatedly to advance through the al-
phabet (e.g., to "B"), or key [1] to go backward. Then press [6] to display
the first available word beginning with the desired letter (e.g., BABY).
Next, press [3] repeatedly to move forward, or [1] to move backward, until
the desired word is displayed (e.g., BACK). Then press [6] to accept the
word and toggle back to the alphabet list.
For selection of the next word (e.g., DOOR), repeat steps 3a or 3b. For 3b,
press key [3] until the first letter of the next word appears (e.g., "D"). Then
press [6] to display the first available word beginning with that letter (e.g.
DAUGHTERS). Press [3] repeatedly until the desired word (e.g., DOOR) ap-
pears. To accept the word, press [6], which toggles back to the alphabet list.
When all desired words have been entered, press [8] to store the description
in memory.
In field *56, the next zone number in sequence will now be displayed for
complete zone information entry.
In field *82, enter [*][N][N], where NN is the next zone that you want to review
or for which you want to program a descriptor. To modify the descriptor, enter
[*][N][N] again. To exit this mode, press [>«][0][0].
Up to five installer-defined words can be added to the built-in vocabulary. Each of
the five "words" can actually consist of a "word string" of several! words, but no
more than ten characters can be used for each word or word string.
1.
2.
Select CUSTOM WORD mode when the question arises.
Key the number ({1]-[5]) of the custom word or word string to be created (for
example, if you are creating the first custom word or word-string, enter [1], for
the second, enter [2], etc.). A cursor will now appear at the beginning of the
second line.
One
of two
methods
of entering
the custom
word's
characters
can now be used (refer to the CHARACTER LIST of letters, numbers, and
symbols on the next page):
Important.
Custom words must begin with an alphabetic character. |f a number
or symbol is used as the first character, the word will not be saved.
a) Press
the [#] key, followed
by the two
digit entry for the
first letter you would like to display (e.g., [6][5] for "A"), or...
b) Use
the
[3] key
to advance
through
the
list of symbols,
numbers, and letters. Use the [1] key to move back through the list.
When you have reached the desired character, press [6] to select it. The cur-
sor will then move to the right, in position for the next character.
Repeat steps 3 and 4 to create the desired word(s). Note that the [4] key can
be used to move the cursor to the left, if necessary, and that key [7] can be
used to enter a blank (or erase an existing character). Remember, no word or
word-string can exceed 10 characters.
Press the [8] key to save the custom word(s) and return to the "CUSTOM ?"
display. Repeat steps 2-5 for other custom words to be entered. To change a
custom word, just overwrite it. If no more are to be entered now, press [0] to
return to the Descriptor entry. The custom word(s) will be automatically added
to the built-in vocabulary.
When zone descriptors are being entered as described in step 3a of the Entering
Zone Descriptors section, the custom word numbers are 250 to 254 for words 1
to 5 respectively. When being entered as described in step 3b of that section,
each word will be found at the end of the group of words that begin with the same
letter as it does.
~28-

Advertisement

Table of Contents
loading

Table of Contents