Special Warnings For The Operator - COMENDA AC2 Series Use And Maintenance Instructions

WARNINGS FOR THE OPERATOR
• Commissioning the machine, the operator must have carefully
read this publication and have acquired extensive knowledge
of the technical specifications and of the machine controls.
EN
• Carefully read the warnings contained in this booklet
as they provide important information regarding safe
installation, use and maintenance. Keep this booklet
carefully for any further consultation by the various operators
• After removing the packaging, check the integrity of the
equipment. If in doubt, do not use it and contact qualified
personnel. The packing elements (plastic bags, expanded
polystyrene, nails, etc.) must not be left within the reach
of children as they are potential sources of danger.
• Before installing the machine, check that the installation
site is compatible with the overall dimensions.
• If it is necessary to install or remove part of the machine,
use only lifting and handling means suitable for the weight.
• Do not allow unauthorised and unqualified personnel
to start, adjust, run or repair the machine. Furthermore,
refer to this manual for the necessary operations.
• The mechanical parts and the electric/electronic components
inside the machine are protected by fully closed panels.
• Before cleaning and/or servicing the machine, make sure
that the main switch is set to "OFF" O in order to disconnect
power from the machine while the operator is working on it.
• Before connecting the equipment, make sure that the
data on the plate correspond to those of the electricity
and water mains
• The electric power system must be provided with an
automatic triggering device upstream of the main switch of
the machine and a suitable earthing system which complies
with all the requirements of industrial accident-prevention
standards.
• If the need arises to work on the main switch or in its vicinity,
disconnect the power to the line that the main switch is
connected to.
• All inspections and maintenance operations which
require the safety guards to be removed must be
carried out under the full responsibility of the user.
It is therefore recommended that only specialised and
authorised technical personnel perform these operations.
• Check that all the accident prevention safety
devices (barriers, guards, casings, microswitches,
etc.) are not tampered with and are in perfect
working order before operation; if not, repair them.
• Do not remove the safety devices.
• In order to avoid personal risks, use only electrical tools
which are correctly connected to the earthing system and
are compliant with the national safety regulations.
• Do not tamper with the electrical system or with
any other mechanism for any reason whatsoever.
• Wear safety gloves when cleaning the machine.
12
SPECIAL • Do not use your hands or unsuitable instruments to locate
leaks from the various hoses. Pressurised or irritating air
could cause serious harm to persons and/or property. Do
not immerse your bare hands in the hot, detergent water
of the tanks. This could cause burns and skin irritations.
If this happens, rinse them immediately and abundantly
with running water.
• Do not use your hands instead of suitable tools
to operate the machine or to stop moving parts
• PAY THE UTMOST ATTENTION TO THE RATING
P L A T E S O N T H E
O P E R A T I N G O N I T O R I N I T S V I C I N I T Y .
• The user must keep all the rating plates legible.
• The user must also replace all rating plates which for
any reason have deteriorated or are not clearly visible,
requesting new ones from the Spare Parts Service.
• In case of malfunctioning of the machine or damage
to its components, contact the maintenance
manager without performing any further repairs.
• It is strictly prohibited for anyone to use the machine for purposes
other than those specifically intended and documented.
The machine must always be used in the ways, times and
places required by good practice standards, by current
laws in every country, even though the specific country may
not have appropriate standards that regulate the sector.
• The manufacturer will not be held liable for
accidents or harm to persons or property
resulting from failure to comply with the safety
requirements and standards indicated herein.
• These requirements, together with standards relative
to machine installation and to electrical connections,
constitute an integral part of the Industrial Accident
Prevention Regulations of each individual country.
• THESE SAFETY STANDARDS INTEGRATE AND DO NOT
REPLACE THE LOCAL SAFETY STANDARDS IN FORCE
• NEVER perform rushed or makeshift repairs which
could compromise correct machine operation.
• IN DOUBT, ALWAYS REQUEST THE INTERVENTION
OF SPECIALIST PERSONNEL.
• ANY TAMPERING BY THE USER RELIEVES THE
MANUFACTURER FROM ALL LIABILITY AND
MAKES THE USER SOLELY RESPONSIBLE
F O R R E S P O N D I N G T O T H E C O M P E T E N T
A C C I D E N T P R E V E N T I O N
• The appliance is not intended to be used by
persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Make sure that children do not play with the appliance.
• It is prohibited to spray water on the appliance to clean it.
M A C H I N E W H E N E V E R
A U T H O R I T I E S .