1. Manuals
  2. Brands
  3. GMC Manuals
  4. Automobile
  5. VE UTE Series
  6. Owner's handbook manual

GMC VE UTE Series Owner's Handbook Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
VE UTE
VE Ute Owner's Handbook

Advertisement

Table of Contents
loading

Related Manuals for GMC VE UTE Series

Summary of Contents for GMC VE UTE Series

  • Page 1 VE UTE VE Ute Owner’s Handbook...
  • Page 2 GM Holden Ltd, ABN 84 006 893 232 (hereinafter Holden) Change of name, address or ownership In the event of a Safety Recall, or for various reasons, Holden may need to contact you as the owner of this vehicle. If you have recently changed your address, or name, or purchased this vehicle second-hand, please help us to help you by taking a few minutes to fill in and mail the forms at the beginning of the Service/warranty booklet.

  • Page 3: Table Of Contents

    CHAPTERS Dashboard ........... 1A Audio system ........1B Locks ............2 Know your vehicle ........3 Driving ............4 Fuel ............5 Emergencies ...........6 Weekly checks ........7 Specifications .........8 Tow and load ..........9 Cleaning ..........10 Index...
  • Page 4 We thank you for choosing Holden and want to assure you of our continuing interest in your driving pleasure and satisfaction. This handbook applies to the current VE Ute series model. Therefore, due to different models and options, you may find reference in this Handbook to some equipment not fitted to your own vehicle.
  • Page 5 ConTEnTS Chapter 1A – Dashboard Chapter 2 – Locks Dashboard layout Keys Instrumentation Ignition switch Warning/reminder indications Door locks Trip computer Bonnet lock Customisation menu Hard tonneau cover lock Steering, horn, hazard warning Tailgate latch Wipers and washers Security Lights Chapter 3 –...
  • Page 6 ConTEnTS cont. Chapter 6 – Emergencies Chapter 8 – Specifications Specifications Customer assistance – Australia General specifications Customer assistance – New Zealand Identification labels Flat tyre Changing a flat tyre Chapter 9 – Tow and load Spare wheel carrier troubleshooting Loading the vehicle Towing a disabled vehicle Towing...
  • Page 7 Dashboard Page Dashboard layout ......1A-2 Instrumentation ......1A-6 Warning/reminder indications ..1A-8 Trip computer ......1A-18 Customisation menu ....1A-23 Steering, horn, hazard warning ......1A-26 Wipers and washers ....1A-27 Lights ......... 1A-28 Cruise control ......1A- 31 Ventilation system......
  • Page 8 1A-2 Chapter 1A DASHBOARD dASHBoARd LAyouT LAyouT IndEx (omEgA/SV6/SS) Page  Glovebox ......................3- 18  Vents ......................1A- 33  Hazard warning switch ...................1A-26  Sunlight sensor ....................1A-44  Infotainment screen ................1B-10, 1B-14  Lever for wipers and washers ................1A-27 ...

  • Page 9: Dashboard

    1A-3 Chapter 1A DASHBOARD dASHBoARd LAyouT cont. omEgA SV6/SS...
  • Page 10 1A-4 Chapter 1A DASHBOARD dASHBoARd LAyouT cont. LAyouT IndEx (SS-V) Page  Glovebox ......................3- 18  Vents ......................1A- 33  Sunlight sensor ....................1A-44  Hazard warning switch ...................1A-26  Sport gauges ....................1A-6  Lever for wipers and washers ................1A-27 ...
  • Page 11 1A-5 Chapter 1A DASHBOARD dASHBoARd LAyouT cont. SS-V...
  • Page 12 1A-6 Chapter 1A DASHBOARD InSTRumEnTATIon gAugES Temperature gauge  The temperature gauge indicates the rpm/000 km/h engine coolant temperature when the ignition is on. Stop-start driving in heavy traffic, driving at high speed in warm weather, hill climbing or towing may cause the needle to move toward the H.
  • Page 13 1A-7 Chapter 1A DASHBOARD InSTRumEnTATIon cont. InfoRmATIon dISPLAyS The instrument panel information display provides visual information to the driver for a number of vehicle functions such as trip computer, audio, warnings and reminders.  Centre display. rpm/000 km/h VEUD1_004 Display – Ignition on When the ignition is switched on, a vehicle system check is performed and the status is shown on the display.
  • Page 14 1A-8 Chapter 1A DASHBOARD WARnIng/REmIndER IndICATIonS WARnIng LAmPS And REmIndERS following warning lamps reminder indications may appear on the instrument panel. They appear as illuminated icons, animated symbols or a combination of both. Most warning/reminder indications are accompanied by a chime. ...
  • Page 15 1A-9 Chapter 1A DASHBOARD WARnIng/REmIndER IndICATIonS cont. ABS fault The Anti-lock Brake System (ABS) warning lamp u illuminates for a short time when the ignition is switched on to verify that no monitored ABS defects are present and to check that the lamp is working.
  • Page 16 1A-10 Chapter 1A DASHBOARD WARnIng/REmIndER IndICATIonS cont. Engine coolant temperature If the Engine Temp Hot animation illuminates when driving, it indicates that the engine coolant temperature is excessively hot. Stop the vehicle as soon as it is safe to do so. The Engine Temp Hot animation is displayed until the TRIP button or the ENTER switch are pressed.
  • Page 17 1A-11 Chapter 1A DASHBOARD WARnIng/REmIndER IndICATIonS cont. Stability control assistance If the Stability Ctrl Assistance animation illuminates when driving, it indicates that the Electronic Stability Program (ESP ® ) is actively helping the vehicle with road grip and stability. CTRL appears at the bottom of the display ®...
  • Page 18 1A-12 Chapter 1A DASHBOARD WARnIng/REmIndER IndICATIonS cont. Low fuel If the Low Fuel animation illuminates when driving, it indicates that the fuel level is low. The Low Fuel animation is displayed until the TRIP button or the ENTER switch are pressed. Y Low Fuel appears at the bottom of the display and remains illuminated until the fuel tank is filled above the low fuel level.
  • Page 19 1A-13 Chapter 1A DASHBOARD WARnIng/REmIndER IndICATIonS cont. Sport shift The Sport Shift animation illuminates when the automatic transmission is operating in sport shift mode. Refer to Automatic transmission in chapter 4. 4 speed 5 & 6 speed Active select The Active Select On animation illuminates when the automatic transmission active select mode is enabled.
  • Page 20 1A-14 Chapter 1A DASHBOARD WARnIng/REmIndER IndICATIonS cont. Check engine warning If the Check Engine animation and the Malfunction Indicator Lamp (MIL) Z illuminate and stay on when driving, the system may require servicing. Although the vehicle may still be drivable and not require towing, take the vehicle to a Holden Dealer as soon as possible.
  • Page 21 1A-15 Chapter 1A DASHBOARD WARnIng/REmIndER IndICATIonS cont. Service The Service animation first appears with the spanner flashing 1,000 km before a service is due, giving you time to arrange for the service to be carried out. The message is shown for 10 seconds or until the TRIP button is pressed whenever the ignition is switched on or off.
  • Page 22 1A-16 Chapter 1A DASHBOARD WARnIng/REmIndER IndICATIonS cont. Battery saver mode on If the Battery Saver Mode On animation illuminates, it indicates that the battery voltage level is low. Alarm activated If the alarm has been activated, the Alarm Activated animation appears for about one second followed by a animation showing which trigger point has activated the alarm.
  • Page 23 1A-17 Chapter 1A DASHBOARD WARnIng/REmIndER IndICATIonS cont. Seat belt warning lamp The X warning lamp reminds vehicle occupants to fasten their seat belts. If the driver’s seat belt is not fastened when the ignition is switched to the ON or START position, the X warning lamp illuminates and the chime sounds for approximately 20 seconds.
  • Page 24 1A-18 Chapter 1A DASHBOARD TRIP ComPuTER VEUD1A_002  The trip computer is shown on the centre display ConTRoLS Press the TRIP button  on the left-hand spoke of the steering wheel to scroll between the trip computer displays and to highlight the values. ...
  • Page 25 1A-19 Chapter 1A DASHBOARD TRIP ComPuTER cont. Odometer/tripmeter The odometer records kilometres travelled since the vehicle was built. The tripmeter shows the kilometres travelled from the start of a particular trip. To reset only the tripmeter to zero, highlight the tripmeter value and press the ENTER switch for more than three seconds.
  • Page 26 1A-20 Chapter 1A DASHBOARD TRIP ComPuTER cont. Average speed/average fuel (excluding LPg vehicles) Avg Speed shows the average speed (while the engine is running) since the trip computer was reset. Avg Fuel shows average fuel used since the trip computer was reset.
  • Page 27 1A-21 Chapter 1A DASHBOARD TRIP ComPuTER cont. To adjust the Manual overspeed value: 1. Rotate the ENTER switch up or down (▲ or ▼) to highlight Manual and press the ENTER switch to highlight the current value. 2. Rotate the ENTER switch up or down to select the desired value in 5 km increments.
  • Page 28 1A-22 Chapter 1A DASHBOARD TRIP ComPuTER cont. ◊ Underspeed chime If an overspeed warning appeared and the vehicle’s speed drops below the set value, underspeed provides a chime to indicate this. Underspeed can be switched on and off in the Customisation menu.
  • Page 29 1A-23 Chapter 1A DASHBOARD CuSTomISATIon mEnu uSIng THE CuSTomISATIon mEnu Entering the Customisation menu Scroll to the Customisation menu using the TRIP button and press the ENTER switch. Note The Customisation menu cannot be opened when the vehicle speed is above 10 km/h. At speeds above 10 km/h, the Customisation menu shows Not Available.
  • Page 30 1A-24 Chapter 1A DASHBOARD CuSTomISATIon mEnu cont. Security For information on the following features, refer to chapter 2. Auto unlock • Choose when you want the doors to unlock automatically. – Off Auto unlock is switched off. – Driver door key out The driver’s door will unlock when the key is removed.
  • Page 31 1A-25 Chapter 1A DASHBOARD CuSTomISATIon mEnu cont. Trip Computer For information on the following features, refer to Trip computer previously in this chapter. Underspeed chime • Choose if you want the underspeed chime to sound. Distance to go • Choose if you want the distance to go display to appear. Distance to go Default •...
  • Page 32 1A-26 Chapter 1A DASHBOARD STEERIng, HoRn, HAzARd WARnIng TILT/REACH STEERIng WARNINg Do not attempt to adjust the steering wheel while driving. Move the lock lever under the steering column downwards. Grasp the steering wheel and move it as required. It can be moved up or down, pulled towards you or pushed away from you.
  • Page 33 1A-27 Chapter 1A DASHBOARD WIPERS And WASHERS oPERATIng THE WIPERS And WASHERS The lever on the left side of the steering column controls the wipers and washers. They operate when the ignition is switched to the ON or ACCESSORIES positions. WARNINg Never operate the wipers on dry glass, as this will damage the rubber and scratch the glass.
  • Page 34 1A-28 Chapter 1A DASHBOARD LIgHTS LIgHTS SWITCH O = Off Turns the headlamps and park lamps off. AUTO = Automatic headlamps Headlamps and park lamps switch on and off automatically. Select high and low beam using the lever. Note Headlamps and park lamps switch on automatically when wipers are operating.
  • Page 35 1A-29 Chapter 1A DASHBOARD LIgHTS cont. ExTERIoR LAmPS Automatic headlamps When the headlamp switch is in the AUTO position, the headlamps and park lamps automatically switch off and on according to the ambient light. Select high and low beam using the lever. Note •...
  • Page 36 1A-30 Chapter 1A DASHBOARD LIgHTS cont. Personal identity keys When the c button is pressed on the key, the system identifies the key and sets the headlamp time delay to the last adjustments used for that key. Refer to Personal identity keys in chapter 2.
  • Page 37 1A-31 Chapter 1A DASHBOARD CRuISE ConTRoL oPERATIng CRuISE ConTRoL The cruise control maintains the vehicle’s speed without you having your foot on the accelerator pedal. Note The cruise control will only operate at speeds above 38 km/h. The cruise control lever is located on the right side of the steering column.
  • Page 38 1A-32 Chapter 1A DASHBOARD CRuISE ConTRoL cont. Pausing the cruise control Press the brake pedal, press the clutch pedal (if the vehicle is fitted with a manual transmission) or press the ON-OFF/CANCEL switch once. This deactivates the cruise control. The Cruise Inactive animation appears, but cruise control retains the speed in its memory.
  • Page 39 1A-33 Chapter 1A DASHBOARD VEnTILATIon SySTEm The vehicle features a flow-through ventilation system for comfort. Under reasonable conditions, it should not be necessary to open the windows at any time. Outside air is drawn into the vehicle through the opening between the bonnet and the windscreen, unless recirculation has been selected.
  • Page 40 1A-34 Chapter 1A DASHBOARD mAnuAL HEATER, AIR CondITIonIng ConTRoLS  Fan speed Recirculation button  Temperature control Air conditioning (A/C) button  Mode control Rear window demister Fan speed  Turn the outer button ring clockwise to increase the fan speed or anticlockwise to reduce it.
  • Page 41 1A-35 Chapter 1A DASHBOARD mAnuAL HEATER, AIR CondITIonIng cont. A/C button Press the A/C button to switch the air conditioning on and off. The lamp in the button illuminates when the air conditioning is on. Note • The fan must be on before the air conditioning will work. •...
  • Page 42 1A-36 Chapter 1A DASHBOARD mAnuAL HEATER, AIR CondITIonIng cont. Air conditioning For a quick cool down when first entering the vehicle on a hot day: 1. Press the A/C button to switch on the air conditioning. 2. Press the button to switch on the recirculation.
  • Page 43 1A-37 Chapter 1A DASHBOARD mAnuAL HEATER, AIR CondITIonIng cont. noTES Unsealed roads (prevention of dust entry) When following another vehicle on unsealed roads (and the dust is airborne), select recirculation. If the dust is not airborne select outside air (recirculation off) and set the fan to high speed.
  • Page 44 1A-38 Chapter 1A DASHBOARD CLImATE ConTRoL The climate control panel is located in the centre of the dashboard. It is designed to maintain the interior of the vehicle at the desired temperature. The temperature for the driver’s and passenger’s side can be adjusted independently. ConTRoLS OFF button ...
  • Page 45 1A-39 Chapter 1A DASHBOARD CLImATE ConTRoL cont. Temperature controls  Turn the temperature controls clockwise (warmer) or anticlockwise (cooler). The temperature can be set between 17 °C and 30 °C (a setting between 22 °C and 24 °C is recommended). The temperature settings for each side are shown in the display.
  • Page 46 1A-40 Chapter 1A DASHBOARD CLImATE ConTRoL cont. Press + or - on the fan button to increase or decrease the fan speed. The fan speed is shown in the display. Note • The climate control sets the fan speed automatically. When adjusting the fan speed, the system will revert to semi-automatic operation.
  • Page 47 1A-41 Chapter 1A DASHBOARD CLImATE ConTRoL cont. A/C button Press the A/C button to switch the air conditioning on and off. A/C appears in the display when the air conditioning is on. A/C OFF appears when it is off. Note or V is selected the air conditioning is automatically switched on.
  • Page 48 1A-42 Chapter 1A DASHBOARD CLImATE ConTRoL cont. Rear window demist button Press the Ü button  to turn the rear demister on. Press the button again to turn the rear demister off. The Ü symbol appears in the display. Note To avoid unnecessary electrical consumption, the rear demister switches off automatically.
  • Page 49 1A-43 Chapter 1A DASHBOARD CLImATE ConTRoL cont. noTES What the system does In automatic operation the system responds quickly to cooling and heating requirements. It is not necessary to set a cooler or hotter temperature than required to ensure fast cooling or heating.
  • Page 50 1A-44 Chapter 1A DASHBOARD CLImATE ConTRoL cont. Hissing Occasionally a slight hissing sound may be heard for a short time when the air conditioning switches off and pressure in the system equalises. This is normal. Water Water condensation forms when the air conditioning is operating, this condensation is discharged underneath the vehicle.
  • Page 51 1A-45 Chapter 1A DASHBOARD CLImATE ConTRoL cont. Switching the climate control off If the climate control is switched off: • background noises may still be noticed coming from the system. It continues to operate to ensure that when the system is switched back on, it will be as close as possible to the temperature set before it was switched off.
  • Page 52 1A-46 Chapter 1A DASHBOARD ® BLuETooTH BLuETooTH ® CAR kIT ® The Bluetooth car kit allows you to answer incoming calls and make outgoing calls on ® your mobile phone without looking at or touching your mobile phone. Your Bluetooth ®...
  • Page 53 1A-47 Chapter 1A DASHBOARD ® BLuETooTH cont. Bluetooth button ® The Bluetooth ® button is located on the right-hand spoke of the steering wheel. Note When pressing the button with the ignition on, a phone symbol appears in the instrument panel centre display for a few seconds.
  • Page 54 1A-48 Chapter 1A DASHBOARD ® BLuETooTH cont. Pairing your mobile phone ® ® The pairing between the Bluetooth capable mobile phone and the Bluetooth car kit can be established as follows: 1. Switch on your mobile phone. 2. Switch on the ignition. 3.
  • Page 55 1A-49 Chapter 1A DASHBOARD ® BLuETooTH cont. Making a call by voice dialling (voice tags) To use the voice dial functions of your mobile phone (provided that your mobile phone is capable), entries for dialling phone numbers with voice dialling have to be prerecorded. ®...
  • Page 56 1A-50 Chapter 1A DASHBOARD ® BLuETooTH cont. Private/hands-free WARNINg Only activate this function if the vehicle is parked. To switch from hands-free to the mobile phone handset: 1. Press and hold the button for three seconds. 2. Continue the call on the mobile phone handset. Press the button to return to the hands-free function.
  • Page 57 1A-51 Chapter 1A DASHBOARD ® BLuETooTH cont. Troubleshooting Problem Cause and solution Mobile phone will not pair • Ignition is switched off. Switch on the ignition. ® up with the Bluetooth • Bluetooth ® is not enabled on the phone. car kit •...
  • Page 58 1A-52 Chapter 1A DASHBOARD noTES...
  • Page 59 Audio Page Steering wheel remote controls (all units) .... 1B-2 Overview (Level 1) ...... 1B-3 Important information....1B-5 Switching on/off ......1B-6 Audio settings ......1B-7 Radio operation ......1B-10 Single CD operation ....1B-14 6 CD changer operation .... 1B-16 AUX operation ......
  • Page 60 1B-2 Chapter 1B AUDIO STEERIng WHEEL REmoTE ConTRoLS (ALL unITS)  AUDIO Button Select source: FM1  FM2  AM  CD  Front AUX  Rear AUX  FM1  FM2  AM  ... Note • The front AUX source is only selectable when an AUX device is plugged in.
  • Page 61 1B-3 Chapter 1B AUDIO oVERVIEW (LEVEL 1) omEgA, SV6 (LEVEL 1 – SIngLE Cd) SS (LEVEL 1 – 6 Cd CHAngER) (oPTIonAL omEgA, SV6) TRACK...
  • Page 62 1B-4 Chapter 1B AUDIO oVERVIEW (LEVEL 1) cont.  Radio preset buttons 1-6.  Radio Mode: Station seek (down). CD Mode short press: Previous Track.  Automatic Station Memory storage ASM. Radio band button. Radio mode: toggle between FM 1, FM2 and AM band (if ASM is not active). Short press: Recall clock/calendar information display.
  • Page 63 1B-5 Chapter 1B AUDIO ImPoRTAnT InfoRmATIon (LEVEL 1) noTES on RAdIo oPERATIon (ALL unITS) • Do not apply any cleaning solution or solvents, or other forms of liquid, to the audio system as this may cause damage to the display and/or electronics, and void the warranty.
  • Page 64 1B-6 Chapter 1B AUDIO SWITCHIng on/off (LEVEL 1) ON/OFF button Switch the audio system on and off by pressing the button On/Off (Using ignition key) The audio system can operate when the ignition key is turned to the Accessories position. When the vehicle’s Accessories Control is turned off by turning the ignition key off (and opening the driver’s door) the audio system (if operating) will be switched off.
  • Page 65 1B-7 Chapter 1B AUDIO AudIo SETTIngS (LEVEL 1) SouRCE (modE) SELECTIon The radio mode can be selected by any of the following actions: • Pressing the button if the previously played source was radio. Pressing the BAND button • Pressing the ASM button ...
  • Page 66 1B-8 Chapter 1B AUDIO AudIo SETTIngS (LEVEL 1) cont. Volume Turning the Volume Control Dial clockwise will increase the volume, turning it anti- clockwise will decrease the volume. Independent Tone Memories This audio system is equipped with Independent Tone Memories. The audio settings can be set independently for each listening mode such as AM, FM and CD.
  • Page 67 1B-9 Chapter 1B AUDIO AudIo SETTIngS (LEVEL 1) cont. Balance To shift the sound towards the right or the left: 1. Enter the Option menu by pressing the Volume Control Dial when the radio is switched on. The menu item ‘AUDIO’ is highlighted. 2.
  • Page 68 1B-10 Chapter 1B AUDIO RAdIo oPERATIon (LEVEL 1) RAdIo dISPLAy Selecting a Radio Band Press the BAND button repeatedly to select one AM and two FM bands (FM1 & FM2). The chosen band will be shown on the display. If the ASM mode is active (‘ASM’...
  • Page 69 1B-11 Chapter 1B AUDIO RAdIo oPERATIon (LEVEL 1) cont. The Local/Distance selection has no effect when the ASM search feature is being used. 1. Access the Option Menu by pressing the Volume Control Dial when the radio source is selected. 2.
  • Page 70 1B-12 Chapter 1B AUDIO RAdIo oPERATIon (LEVEL 1) cont. Automatic Station Memory (ASM)  This feature allows the storage of an additional 6 AM and 6 FM radio stations. It is of great benefit when travelling long distances, e.g. on holidays, since you can store the strongest radio stations without knowing their frequency.
  • Page 71 1B-13 Chapter 1B AUDIO RAdIo oPERATIon (LEVEL 1) cont. Interference Interference is caused by either natural or man made electrical disturbances. This can affect the amplitude of the reception signal. AM signals are more prone to this type of interference than FM signals. This type of interference has little or no effect on the frequency of the reception signal, thus AM is susceptible to interference from power lines, fluorescent lighting, neon signs, traffic light control circuits, overhead tram wires and electrical storms.
  • Page 72 1B-14 Chapter 1B AUDIO SIngLE Cd oPERATIon (LEVEL 1) The CD drive is built into the audio system and CDs are loaded through the CD slot on the front face of the audio system. Note The CD drive is designed for standard 12 cm CDs only. Using incorrect sized CDs (e.g.
  • Page 73 1B-15 Chapter 1B AUDIO SIngLE Cd oPERATIon (LEVEL 1) cont. Fast Forward/Fast Back (Track Cue/Review) 1. Press and hold the button or the button to rapidly move forwards or backwards within the current track. CD Random When this feature is selected, all tracks on the current CD will be played in random order.
  • Page 74 1B-16 Chapter 1B AUDIO 6 Cd CHAngER oPERATIon (LEVEL 1) 6 CD Changer Operation The CD Changer holds up to six CDs at one time. The Changer is built into the audio system and CDs are loaded through the single slot on the front face of the audio system, after pressing the LOAD button (refer to ‘Loading a CD’...
  • Page 75 1B-17 Chapter 1B AUDIO 6 Cd CHAngER oPERATIon (LEVEL 1) cont. Loading a CD To load a CD into the CD Changer, briefly press the LOAD button . When the Changer is ready to accept the CD, ‘Insert Disc’ will be displayed. will flash green, and the audio system will beep twice.

  • Page 76: Audio System

    1B-18 Chapter 1B AUDIO 6 Cd CHAngER oPERATIon (LEVEL 1) cont. Playing CDs • Press the button if the previous mode was CD. Press the CD button  • if the vehicle’s accessories or ignition is on. Press the CD button ...
  • Page 77 1B-19 Chapter 1B AUDIO 6 Cd CHAngER oPERATIon (LEVEL 1) cont. Choosing Track and Folder using the MP3-Browse Mode When listening to MP3-CDs, you can browse the directories (folders) and tracks of the MP3-CD to find a track more easily. To choose a track in the actual folder: 1.
  • Page 78 1B-20 Chapter 1B AUDIO 6 Cd CHAngER oPERATIon (LEVEL 1) cont. CD Random You can choose between different modes for random play: • RANDOM TRACK for CD, • RANDOM DISC for CD, • RANDOM IN DISC for MP3-CDs and • RANDOM IN FOLDER for MP3-CDs.
  • Page 79 1B-21 Chapter 1B AUDIO Aux oPERATIon (LEVEL 1) AUX operation This unit is equipped with an AUX input socket at the front of the audio system. You can connect any suitable audio source to the AUX input socket e.g. portable MP3 player.
  • Page 80 1B-22 Chapter 1B AUDIO AddITIonAL fEATuRES (LEVEL 1) Speed Dependent Volume (SDV) The SDV system adjusts the audio system volume depending on the vehicle’s speed. As the vehicle’s speed increases, the volume of the audio system also increases to compensate for the driving noise. Note This feature will never completely compensate for the driving noise.
  • Page 81 1B-23 Chapter 1B AUDIO AddITIonAL fEATuRES (LEVEL 1) cont. To turn distortion limiting on and off: 1. Enter the Options menu by pressing the Volume Control Dial when the audio system is switched on. The menu item ‘AUDIO’ is highlighted. 2.
  • Page 82 1B-24 Chapter 1B AUDIO oVERVIEW (SS-V) SS-V...
  • Page 83 1B-25 Chapter 1B AUDIO oVERVIEW (SS-V) cont. ConTRoLS  CD Load button. Long press: To Load all discs. Single press: To Load one disc.  Short press: Show time and date. Long press: Adjust clock and calendar.  Enter Help menu. Automatic Station Memory storage.
  • Page 84 1B-26 Chapter 1B AUDIO ImPoRTAnT InfoRmATIon (SS-V) noTES on RAdIo oPERATIon • Do not apply any cleaning solution or solvents, or other forms of liquid, to the audio system as this may cause damage to the display and/or electronics, and void the warranty.
  • Page 85 1B-27 Chapter 1B AUDIO ImPoRTAnT InfoRmATIon (SS-V) cont. SETTIng THE CLoCk & CALEndAR Note The clock and calendar can be adjusted when the audio system is either on or off. Adjust the clock and calendar as follows: 1. Press and hold the TIME button ...
  • Page 86 1B-28 Chapter 1B AUDIO SWITCHIng on/off (SS-V) on/off Switch the audio system off and on by pressing the button On/Off (Using ignition key) The audio system can operate when the ignition key is turned to the Accessories position. When the vehicle’s Accessories Control is turned off by turning the ignition key off and opening the driver’s door, the audio system (if operating) will be switched off.
  • Page 87 1B-29 Chapter 1B AUDIO PERSonAL IdEnTITy kEyS (SS-V) Memory 1 and Memory 2 This audio system features Personal Identity Memories, which provide two different memories of electronic settings for different ignition keys. For the sound system the following settings are individually memorised by the key system and become unique to the particular key: •...
  • Page 88 1B-30 Chapter 1B AUDIO AudIo SETTIngS (SS-V) SouRCE (modE) SELECTIon The radio mode can be selected by any of the following actions: • Pressing the button if the previously played source was radio. Pressing the BAND button • The CD mode can be selected by any of the following actions: •...
  • Page 89 1B-31 Chapter 1B AUDIO AudIo SETTIngS (SS-V) cont. Treble 1. Enter the Option menu by pressing the Menu Control Dial when the audio system is switched on. The menu item ‘Audio’ is highlighted. 2. Press the Menu Control Dial to access the audio menu. 3.
  • Page 90 1B-32 Chapter 1B AUDIO AudIo SETTIngS (SS-V) cont. EquALIzER funCTIon The audio unit is equipped with five pre-programmed equalizer curves. Each of these curves have been factory-programmed to enhance a particular style of music. However it may be used with any type. To turn this function on or off, or to scroll through the five EQ curves, press the EQ button one or more times.
  • Page 91 1B-33 Chapter 1B AUDIO AudIo SETTIngS (SS-V) cont. LoudnESS ConTouR CIRCuIT A user selectable loudness contour circuit to enhance the Bass and Treble response at low volume levels can be activated if you feel that the sound system needs more bass and treble at low listening levels.
  • Page 92 1B-34 Chapter 1B AUDIO RAdIo oPERATIon (SS-V) Radio Display Selecting a Radio Band Press the BAND button repeatedly to select one AM and two FM bands (FM1 & FM2). The chosen band will be shown on the display. If the ASM mode is active (‘ASM’ appears on the display), one AM ASM band and one FM ASM band can be selected.
  • Page 93 1B-35 Chapter 1B AUDIO RAdIo oPERATIon (SS-V) cont. Note The Local/Distance selector has no effect when the ASM search feature is being used. 1. Access the Option menu by pressing the Menu Control Dial when the radio is switched on. 2.
  • Page 94 1B-36 Chapter 1B AUDIO RAdIo oPERATIon (SS-V) cont. Automatic Station Memory (ASM) This feature allows the storage of additional 6 AM and 6 FM radio stations. It is of great benefit when travelling long distances, e.g. on holidays, since you can store the strongest radio stations without knowing their frequency.
  • Page 95 1B-37 Chapter 1B AUDIO RAdIo oPERATIon (SS-V) cont. Interference Interference is caused by either natural or man made electrical disturbances. This can affect the amplitude of the reception signal. AM signals are more prone to this type of interference than FM signals. This type of interference has little or no effect on the frequency of the reception signal, thus AM is susceptible to interference from power lines, fluorescent lighting, neon signs, traffic light control circuits, overhead tram wires and electrical storms.
  • Page 96 1B-38 Chapter 1B AUDIO Cd CHAngER oPERATIon (SS-V) The CD Changer holds up to six CDs at one time. The Changer is built into the audio system and CDs are loaded through the single slot on the front face of the audio system, after pressing the LOAD button ...
  • Page 97 1B-39 Chapter 1B AUDIO Cd CHAngER oPERATIon (SS-V) cont. MP3 Display • Press the softkey DISPLAY MODE repeatedly until the desired display mode is shown. For MP3-CD operation the following modes are available: • Normal mode with folder number, track number and playtime. •...
  • Page 98 1B-40 Chapter 1B AUDIO Cd CHAngER oPERATIon (SS-V) cont. Loading a CD To load a CD into the CD Changer, briefly press the LOAD button  . When the Changer is ready to accept the CD, ‘Insert Disc’ will be displayed. will flash green, and the audio system will beep twice (if The Load Indicator Light beeps are turned on).
  • Page 99 1B-41 Chapter 1B AUDIO Cd CHAngER oPERATIon (SS-V) cont. Playing CDs • Press the button if the previous mode was CD. Press the CD button  • Stopping a CD Press the BAND button to stop CD playback and resume in radio mode or press the AUX button to stop CD playback and resume in AUX mode, or press the button...
  • Page 100 1B-42 Chapter 1B AUDIO Cd CHAngER oPERATIon (SS-V) cont. Choosing Track and Folder using the MP3-Browse Mode When listening to MP3-CDs, you can browse the directories (folders) and tracks of the MP3-CD to find a track more easily. To choose a track in the current folder. 1.
  • Page 101 1B-43 Chapter 1B AUDIO Cd CHAngER oPERATIon (SS-V) cont. CD Random You can choose between different modes for random play: • RANDOM TRACK for CD, • RANDOM DISC for CD, • RANDOM IN DISC for MP3-CDs and • RANDOM IN FOLDER for MP3-CDs. 1.
  • Page 102 1B-44 Chapter 1B AUDIO Aux oPERATIon (SS-V) AUX operation WARNINg Do not connect, disconnect or adjust portable devices while driving the vehicle. This unit is equipped with an AUX input socket at the front of the audio system. You can connect any suitable audio source to the AUX-input socket e.g. portable MP3 player. There is also a secondary AUX input connector on the rear of the audio system for use with an optional DVD player.
  • Page 103 1B-45 Chapter 1B AUDIO AddITIonAL fEATuRES (SS-V) Help menu This unit is equipped with a help menu to help you understand the audio system and its functions. Button help You can display help texts for each of the audio system buttons. 1.
  • Page 104 1B-46 Chapter 1B AUDIO AddITIonAL fEATuRES (SS-V) cont. AddITIonAL AudIo SETTIngS Dynamic Distortion Limiter (DDL) Your audio system is equipped with a system that limits the amount of amplifier distortion that you can hear. When this feature is turned on it continuously monitors the quality of the signal to the speakers.
  • Page 105 1B-47 Chapter 1B AUDIO AddITIonAL fEATuRES (SS-V) cont. 1. Access the Option menu by pressing the Menu Control Dial when the audio system is switched on. 2. Highlight the menu item ‘Audio setup’ by turning the Menu Control Dial clockwise. 3.
  • Page 106 1B-48 Chapter 1B AUDIO AddITIonAL fEATuRES (SS-V) cont. dISPLAy SETTIngS You can adjust several settings of the display e.g. brightness and contrast to meet your needs. Brightness setting The brightness is adjustable from -5 to +5. 1. Access the Option menu by pressing the Menu Control Dial when the audio system is switched on.
  • Page 107 1B-49 Chapter 1B AUDIO AddITIonAL fEATuRES (SS-V) cont. Contrast setting (DVD player mode only 1. Access the Option menu by pressing the Menu Control Dial when the audio system is switched on. 2. Highlight the menu item ‘Display’ by turning the Menu Control Dial clockwise.
  • Page 108 1B-50 Chapter 1B AUDIO AddITIonAL fEATuRES (SS-V) cont. Colour Setting 1. Access the Option menu by pressing the Menu Control Dial when the audio system is switched on. 2. Highlight the menu item ‘Display’ by turning the Menu Control Dial clockwise.
  • Page 109 1B-51 Chapter 1B AUDIO TELEPHonE (ALL unITS) This audio system includes an additional telephone facility, as well as the Bluetooth ® phone interface on some models. Refer to Bluetooth ® in chapter 1A. The telephone connection point in the vehicle’s wiring contains circuits that run directly to the audio system.
  • Page 110 1B-52 Chapter 1B AUDIO AnTEnnA InfoRmATIon (ALL unITS) Fixed mast antenna To remove the roof antenna, rotate it anticlockwise. To install the roof antenna, rotate it clockwise. WARNINg Driving through an automatic vehicle wash with the antenna installed may result in damage to the antenna or the roof panel.
  • Page 111 1B-53 Chapter 1B AUDIO noTES on ComPACT dISCS (ALL unITS) • Handle the CD by its edge and avoid touching the playing surface. • Do not stick paper labels, tape, etc., and do not write on either surface. • Do not expose the CD to direct sunlight or a heat source such as a hot air duct for longer periods.
  • Page 112 1B-54 Chapter 1B AUDIO noTES...
  • Page 113 Locks Page Keys..........2-2 Ignition switch .........2-6 Door locks ........2-7 Bonnet lock ........2-10 Hard tonneau cover lock .....2-11 Tailgate latch.........2-13 Security.........2-14 The asterisk signifies equipment options not in all vehicles, model variants, engine options, optional equipment and Genuine Holden Accessories (and Parts).
  • Page 114 Chapter 2 LOCKS kEyS This key operates all locks and ignition, except for the glovebox. The following buttons appear on the key. Lock: Press the button on the key to lock the doors and to arm the alarm system. Unlock: Press the button on the key to unlock the doors and to disarm the alarm system.

  • Page 115: Locks

    Chapter 2 LOCKS kEyS cont. Foldaway key blade Press the button to extend the key blade. To retract the key blade, press the button and fold the key section into the remote. Note • The key engages audibly. • A fixed blade key is supplied as the VEUD2_007 second key.
  • Page 116 Chapter 2 LOCKS kEyS cont. PERSonAL IdEnTITy kEyS This system stores two sets of electronic settings. The settings are stored when a personal identity key is removed from the ignition and are recalled when the button is pressed on the key. For instance, one driver may have a preferred radio station. Pressing the button on their key automatically customises the radio for that driver.
  • Page 117 Chapter 2 LOCKS kEyS cont. noTES ABouT THE kEyS • When a button on the key is pressed, it sends a signal to the vehicle. The receiver of the signal is incorporated in the rear window shelf trim panel. • The remote control in the key has a range of approximately 10 metres.
  • Page 118 Chapter 2 LOCKS IgnITIon SWITCH IgnITIon PoSITIonS WARNINg Do not switch the engine off while the vehicle is moving as there will not be any power assist for brakes or steering. Never remove the key while the vehicle is moving, as this will lock the steering. Lock When the key is in the LOCK position, some electrical accessories and the...
  • Page 119 Chapter 2 LOCKS dooR LoCkS LoCkIng Doors are locked when the lock snib is flush with the door handle. If the snib is showing red, the door is unlocked. Refer to Door lock snibs further on in this chapter. Note You can select the Auto lock feature which locks the doors automatically when the vehicle’s speed is at or above 13 km/h.
  • Page 120 Chapter 2 LOCKS dooR LoCkS cont. Locking from the inside Press the side of the switch with the symbol on the centre console to lock all doors. This will not arm the alarm. If locking has not worked Note The horn chirps rapidly five times if any door is open while the e button on the key is pressed.
  • Page 121 Chapter 2 LOCKS dooR LoCkS cont. Manual unlocking Insert the key into the lock of the driver’s door and turn it once towards the front of the vehicle to unlock the driver’s door. Turn it twice towards the front of the vehicle to unlock all doors.
  • Page 122 2-10 Chapter 2 LOCKS BonnET LoCk oPEnIng THE BonnET From the driver’s side of the vehicle, pull the lever towards you. This allows the bonnet to release but is prevented from opening by the safety catch. To open the bonnet completely, reach under the bonnet to the passenger’s side of the emblem and push up on the front edge of the release catch.
  • Page 123 2-11 Chapter 2 LOCKS HARd TonnEAu CoVER LoCk WARNINg • Sitting or standing in the cargo area or on the surface of the hard tonneau cover while the vehicle is in motion may lead to serious injury or death. • Do not carry volatile materials or liquids within the cargo area while the hard tonneau cover is shut as harmful fumes or gases may accumulate.
  • Page 124 2-12 Chapter 2 LOCKS HARd TonnEAu CoVER LoCk cont. Manual unlocking Insert the hard tonneau cover key into the lock, turn it towards the driver’s side to unlock, then lift to open. Note If the tonneau cover is opened using •...
  • Page 125 2-13 Chapter 2 LOCKS TAILgATE LATCH The tailgate latch is located on the inside of the tailgate. While facing the front of the vehicle, turn the latch toward the passenger’s side, to open. To close, push the tailgate to the upright position until it engages.
  • Page 126 2-14 Chapter 2 LOCKS SECuRITy ALARm Arming and disarming When the button on the key is pressed or when the vehicle is locked using the key in the driver’s door lock, the alarm is armed automatically (after a short delay of approximately 30 seconds).
  • Page 127 2-15 Chapter 2 LOCKS SECuRITy cont. The following messages are possible depending upon the model and what has activated the alarm: by Bonnet – if the bonnet has been opened. • by Passenger door – if the passenger door has been opened. •...
  • Page 128 2-16 Chapter 2 LOCKS SECuRITy cont. Immobiliser This vehicle is fitted with an immobiliser. It prevents unauthorised engine starting. The ignition key will be recognised by the vehicle when the key is inserted into the ignition switch allowing the engine to be started. When difficulties in starting the vehicle are experienced, check the following points.
  • Page 129 Know your vehicle Page Seats ..........3-2 Front seats ........3-2 Restraints ........3-5 Child restraints ......3-7 Supplemental restraint system ..3-11 Airbags ........3-11 Seatbelt pretensioners ....3-13 Power windows......3-14 Mirrors ..........3-15 External rear view mirrors ..3-15 Internal mirrors ......3-16 Interior lamps ........3-17 Storage compartments ....3-18 Power socket ........3-21 Retained accessory power and battery saver ......3-22...

  • Page 130: Know Your Vehicle

    Chapter 3 KNOW YOUR VEHICLE SEATS fRonT SEATS WARNINg Do not adjust the driver’s seat when the vehicle is moving as the seat could move suddenly causing the driver to lose control. Seat adjustment (seats with a single switch, 4-way) To adjust the height •...
  • Page 131 Chapter 3 KNOW YOUR VEHICLE SEATS cont. To tilt the seat forward: • Pull the dump latch lever on the side of the seat back. The seat will tilt forwards. • To return the seat to its original position, push the seat back rearward until the latch is locked in position.
  • Page 132 Chapter 3 KNOW YOUR VEHICLE SEATS cont. Head restraint WARNINg • This safety feature is not intended as a headrest. It is solely for the reduction of whiplash neck movement in an accident involving your vehicle. • The centre of the head restraint should be at eye level, never at neck level.
  • Page 133 Chapter 3 KNOW YOUR VEHICLE RESTRAInTS SEATBELTS WARNINg • Seatbelts are designed to bear upon the bony structure of the body, and should be worn low across the front of the pelvis or the pelvis, chest and shoulders, as applicable; wearing the lap section of the belt across the abdominal area must be avoided.
  • Page 134 Chapter 3 KNOW YOUR VEHICLE RESTRAInTS cont. Lap/sash belts To fasten the seatbelt: • Pull the metal tongue across your body and clip it into the buckle. • When the metal tongue is locked safely into place you will hear a ‘click’. •...
  • Page 135 Chapter 3 KNOW YOUR VEHICLE RESTRAInTS cont. CHILd RESTRAInTS WARNINg – EXTREME HAZARD • Do not use a rearward facing child restraint on a seat protected by an airbag in front of it. The child could be seriously injured if the airbag inflates, as the child’s head would be very close to the inflating airbag.
  • Page 136 Chapter 3 KNOW YOUR VEHICLE RESTRAInTS cont. Booster seats are for when children outgrow a typical forward-facing child seat but they are still too small for lap/sash seatbelts. A booster seat raises the child so that the knees bend comfortably, the lap/sash seatbelt is correctly positioned and the child can see out the window.
  • Page 137 Chapter 3 KNOW YOUR VEHICLE RESTRAInTS cont. Anchorage points • Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seatbelts, harnesses, or for attaching other items or equipment to the vehicle. •...
  • Page 138 3-10 Chapter 3 KNOW YOUR VEHICLE RESTRAInTS cont. Holden child restraint anchor fitting If the child restraint anchor fitting is ever removed ensure that the bolt is securely tightened to 20 ± 5 Nm (Newton metres). Check with your Holden Dealer if unsure.
  • Page 139 3-11 Chapter 3 KNOW YOUR VEHICLE SuPPLEmEnTAL RESTRAInT SySTEm AIRBAgS When airbags inflate, an operating noise may be heard and a small amount of smoke- like gas is released. The gas is harmless and does not indicate malfunction or fire. The airbag then deflates, with the whole process taking only a moment.
  • Page 140 3-12 Chapter 3 KNOW YOUR VEHICLE SuPPLEmEnTAL RESTRAInT SySTEm cont. Airbags and child restraints WARNINg – EXTREME HAZARD • Do not use a rearward facing child restraint on a seat protected by an airbag in front of it. The child could be seriously injured if the airbag inflates, as the child’s head would be very close to the inflating airbag.
  • Page 141 3-13 Chapter 3 KNOW YOUR VEHICLE SuPPLEmEnTAL RESTRAInT SySTEm cont. SEATBELT PRETEnSIonERS The seatbelt system incorporates seatbelt pretensioners. They are part of the Supplemental Restraint System (SRS). In certain severe frontal or rear collisions, both belt buckles are pulled downwards, instantly tightening both the sash and the lap sections of the seatbelt.
  • Page 142 3-14 Chapter 3 KNOW YOUR VEHICLE PoWER WIndoWS oPERATIng THE PoWER WIndoWS The power window switches are located between the front seats. The switches are operational when the ignition is switched on or the c button on the key is pressed. WARNINg Before operating the power windows, check they are free of obstructions and...
  • Page 143 3-15 Chapter 3 KNOW YOUR VEHICLE mIRRoRS ExTERnAL REAR VIEW mIRRoRS To adjust the external rear view mirrors, switch the ignition on and use the switches in the centre console as follows:  • Move switch to the right to operate the right hand side mirror.
  • Page 144 3-16 Chapter 3 KNOW YOUR VEHICLE mIRRoRS cont. InTERnAL mIRRoRS Internal rear view mirror Push the lever on the lower edge of the mirror forwards (away from you) and then adjust the position of the mirror. reduce headlamp glare from following vehicles, pull...
  • Page 145 3-17 Chapter 3 KNOW YOUR VEHICLE InTERIoR LAmPS oPERATIng THE InTERIoR LAmPS Note The operation of interior lamps is also affected by the battery saver feature. Refer to Battery saver further on in this chapter. Interior (dome) lamp The interior lamp is located in the centre-front of the roof.
  • Page 146 3-18 Chapter 3 KNOW YOUR VEHICLE SToRAgE ComPARTmEnTS gLoVEBox The glovebox is located in the dashboard directly in front of the passenger seat. To open the glovebox, pull the handle towards you. To close, push the lid firmly back into place. A key is provided solely to lock and unlock the glovebox.
  • Page 147 3-19 Chapter 3 KNOW YOUR VEHICLE SToRAgE ComPARTmEnTS cont. SungLASSES HoLdER The sunglasses holder is located in the roof and is designed to accommodate one pair of sunglasses. To open, push in the rear of the lid and release it. To close, swivel the holder back to its original position and press in the rear of the lid to engage the latch.
  • Page 148 3-20 Chapter 3 KNOW YOUR VEHICLE SToRAgE ComPARTmEnTS cont. fRonT SEAT-BACk PoCkETS A storage pocket is located on the rear of both front seats. CABIn SToRAgE ComPARTmEnTS Storage compartments are located at the rear of the cabin for the storage of lightweight items, not exceeding 2 kg in total (e.g.
  • Page 149 3-21 Chapter 3 KNOW YOUR VEHICLE PoWER SoCkET The power socket is located inside the centre console. The power socket is operational when the ignition is switched to either ON or ACCESSORIES. Note Any accessory device (e.g. mobile phone, car fridge) connected to the power socket must not exceed a current draw of 10 amps.
  • Page 150 3-22 Chapter 3 KNOW YOUR VEHICLE RETAInEd ACCESSoRy PoWER And BATTERy SAVER RETAInEd ACCESSoRy PoWER (RAP) The power windows will work when the key is in the ON or ACCESSORIES positions. Once the ignition is switched to LOCK, the RAP allows the power windows to continue to operate for up to 10 minutes.
  • Page 151 3-23 Chapter 3 KNOW YOUR VEHICLE SofT TonnEAu CoVER InSTALLIng THE TonnEAu CoVER 1. Remove the cover, front bar and bows from the tonneau cover bag. VEUD3_080 Installing bows The tonneau cover is supplied with two bows. Note The front and rear bows are different lengths.
  • Page 152 3-24 Chapter 3 KNOW YOUR VEHICLE SofT TonnEAu CoVER cont. Fitting the tonneau cover 5. Place the tonneau cover roughly in position over the tray with the attached bar towards the front of the vehicle. 6. Fit one end of the bar into either the left-hand or right-hand slot as shown.
  • Page 153 3-25 Chapter 3 KNOW YOUR VEHICLE SofT TonnEAu CoVER cont. 8. The front edge of the cover has a magnetic strip, ensure it is seated down correctly. VEUD3_084 9. Lay the tonneau cover over the bows. 10. Starting from the rear, use the finger loops to pull the cover’s plastic strip over the slot provided around the top edge of the load area.
  • Page 154 3-26 Chapter 3 KNOW YOUR VEHICLE SofT TonnEAu CoVER cont. REmoVIng THE TonnEAu CoVER 1. Using the finger loops provided, remove the cover by pulling the loops out and up. From underneath the cover, remove the front bar on one side, by pushing it towards the front of the vehicle and tilting down.
  • Page 155 3-27 Chapter 3 KNOW YOUR VEHICLE SofT TonnEAu CoVER cont. Storing The soft tonneau cover, front bar and bows may be stored behind the front seats as shown. fITTIng THE TonnEAu CoVER WITH HIgH LoAdS The cover can be adjusted for higher loads.
  • Page 156 3-28 Chapter 3 KNOW YOUR VEHICLE HARd TonnEAu CoVER WARNINg • Sitting or standing in the cargo area or on the surface of the hard tonneau cover while the vehicle is in motion may lead to serious injury or death. •...
  • Page 157 3-29 Chapter 3 KNOW YOUR VEHICLE HARd TonnEAu CoVER cont. 4. With the aid of an assistant hold the tonneau cover in its open position. 5. Remove the struts from the upper ball pins. Using a small flat-bladed screwdriver, lever the retaining clips open approximately 3 mm as shown ...
  • Page 158 3-30 Chapter 3 KNOW YOUR VEHICLE HARd TonnEAu CoVER cont. VEUD3_102   8. Lift the retaining pins away from their retaining clips  9. Slide both retaining pins towards the middle of the load area until they are clear of the centre hinge section (upper hinge).
  • Page 159 3-31 Chapter 3 KNOW YOUR VEHICLE HARd TonnEAu CoVER cont. Refitting of the hard tonneau 1. Instal the gas struts onto the lower ball pins in the load area. Note • Always fit the strut with the wiring connections to the left hand side. •...
  • Page 160 3-32 Chapter 3 KNOW YOUR VEHICLE SPoRTS BAR Sports bar The sports bar is an appearance item only. It does not provide additional protection in an accident and should not be used as a tie down point for loads.
  • Page 161 Driving Page Safety ..........4-2 Driving precautions ......4-3 Park brake ........4-5 Engine starting........4-6 Transmission operation ....4-7 Automatic transmission ...4-7 Manual transmission .....4-19 Active safety systems ....4-20 Anti-lock brake system (ABS) ......4-20 Electronic stability ® program (ESP ) ......4-21 Electronic brake assist (EBA) ......4-23 Add on equipment ......4-24 The asterisk signifies equipment options not in all vehicles, model variants, engine options,...
  • Page 162 Chapter 4 DRIVING SAfETy BEfoRE EnTERIng THE VEHICLE • Check that windows, mirrors and lamps are clean. • Visually check tyre inflation. Note Check the tyre pressures each week. BEfoRE dRIVIng off 1. Ensure that both doors are closed and secured. 2.

  • Page 163: Driving

    Chapter 4 DRIVING dRIVIng PRECAuTIonS RunnIng-In Your vehicle does not need an elaborate running-in procedure. But it will perform better in the long run if you follow these guidelines: • Do not drive at any one constant speed, fast or slow, for the first 1000 km. Do not make full-throttle starts.
  • Page 164 Chapter 4 DRIVING dRIVIng PRECAuTIonS cont. LoAdIng THE VEHICLE Loading the vehicle changes the mass distribution and therefore the handling when driving. After loading the vehicle, take care to become familiar with the vehicle’s driving characteristics. Refer to Loading the vehicle in chapter 9. LooSE ARTICLES Do not leave loose articles or luggage in the passenger compartment.
  • Page 165 Chapter 4 DRIVING PARk BRAkE oPERATIng THE PARk BRAkE The park brake lever is located between the front seats. Applying the park brake To apply, pull the lever straight up, without pressing the release button. When the ignition is switched on and the park brake is applied, the park brake warning lamp R on the instrument panel illuminates.
  • Page 166 Chapter 4 DRIVING EngInE STARTIng 1. Ensure that the park brake is firmly applied and release it only after you have started the engine and are ready to drive off. : Fully depress the clutch pedal to the floor, shift the gear 2.
  • Page 167 Chapter 4 DRIVING TRAnSmISSIon oPERATIon AuTomATIC TRAnSmISSIon gear selector lever Press the select button on the front of the transmission gear selector lever to move into any position indicated by the arrows.
  • Page 168 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. gear display When the position of the transmission gear selector is changed, an animation is shown on the instrument panel centre display. The selected gear is magnified and changes according to the selector lever’s movement. The gears displayed are P R N D 3 2 1 (vehicles with 4 speed transmission) or P R N D (vehicles with 5 or 6 speed transmission).
  • Page 169 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. 4 speed transmission selector lever positions Note The engine will not start unless the transmission gear selector is in position P (park) or N (neutral). P (park) In this position, the driven (rear) wheels are locked prevent vehicle from moving.
  • Page 170 4-10 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. Used for general driving. The transmission can shift between all forward gears as required. It is recommended that D be selected with Sport shift mode when towing on the highway at speeds over 80 km/h. Note If on a steep downhill gradient, the transmission may not shift up from 1st to 2nd gear depending on the conditions.
  • Page 171 4-11 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. 5 speed transmission selector lever positions Note The engine will not start unless the transmission gear selector is in position P (park) or N (neutral). P (park) In this position the driven (rear) wheels are locked to prevent the vehicle from moving.
  • Page 172 4-12 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. D (drive) This is the normal driving position. The transmission automatically selects the appropriate gear according to the current load and driving conditions. After selecting D from P or N, pause for a moment before accelerating, to allow the transmission to engage the forward gear.
  • Page 173 4-13 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. 6 speed transmission selector lever positions Note The engine will not start unless the transmission gear selector is in position P (park) or N (neutral). P (park) In this position the driven (rear) wheels are locked to prevent the vehicle from moving.
  • Page 174 4-14 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. D (drive) This is the normal driving position. The transmission automatically selects the appropriate gear according to the current load and driving conditions. After selecting D from P or N, pause for a moment before accelerating, to allow the transmission to engage the forward gear.
  • Page 175 4-15 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. SPoRT SHIfT modE (SELECT THE 1 BuTTon) 4 speed transmission Sport shift mode can be selected where maximum engine power and transmission responsiveness is required. When operated in Sport shift mode, the transmission will delay upshifts and allow earlier downshifts, so that lower gears/higher engine speeds are used for most driving conditions improving vehicle performance and acceleration.
  • Page 176 4-16 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. SPoRT SHIfT modE 5 and 6 speed transmission Sport shift mode can be selected where maximum engine power and transmission responsiveness is required. When operated in Sport shift mode, the transmission will delay upshifts and allow earlier downshifts, so that lower gears/higher engine speeds are used for most driving conditions, improving vehicle performance and acceleration.
  • Page 177 4-17 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. noRmAL SHIfT modE Normal shift mode is recommended for normal or freeway driving, as it provides optimum fuel economy. When the ignition is switched on, normal shift mode is selected automatically. When normal shift mode is selected (Sport shift mode off), the Normal Shift animation illuminates in the display for two seconds and the display then reverts to the original trip computer display.
  • Page 178 4-18 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. Active Select (A/S) mode cont. When shifting up or down, the selected gear (1, 2, 3, 4 or 5 on vehicles with 5 speed transmission, or 1, 2, 3, 4, 5, or 6 on vehicles with 6 speed transmission) is also animated in the centre display.
  • Page 179 4-19 Chapter 4 DRIVING TRAnSmISSIon oPERATIon cont. mAnuAL TRAnSmISSIon Shift patterns The manual transmissions fitted to vehicles with V6 and V8 engines have six forward gears and a reverse gear. The shift pattern illustrated is also found on the top of the gear shift lever. When selecting R (reverse), shift the gear lever sideways against spring pressure in order to engage the gear.
  • Page 180 4-20 Chapter 4 DRIVING ACTIVE SAfETy SySTEmS AnTI-LoCk BRAkE SySTEm Monitoring The Anti-lock Brake System (ABS) continuously monitors the vehicle’s braking system and prevents the wheels from locking up when braking. It starts to regulate the braking as soon as a wheel shows a tendency to lock. The ABS allows maximum braking effort while full steering control is retained, even in the event of panic braking.
  • Page 181 4-21 Chapter 4 DRIVING ACTIVE SAfETy SySTEmS cont. ELECTRonIC STABILITy PRogRAm (ESP ® Operation ® The Electronic Stability Program (ESP ) is an advanced feature that works in conjunction with the vehicle’s Anti-lock Braking System (ABS) and includes the ® Traction Control System (TCS).
  • Page 182 4-22 Chapter 4 DRIVING ACTIVE SAfETy SySTEmS cont. ® ® To switch the ESP off (i.e. ESP TCS), press the button located in front of the transmission gear selector lever or gear shift lever, depending on the transmission fitted to your vehicle. Press the button again to switch the ®...
  • Page 183 4-23 Chapter 4 DRIVING ACTIVE SAfETy SySTEmS cont. ELECTRonIC BRAkE ASSIST (EBA) ® The EBA is incorporated into the ESP system and detects an emergency braking situation. It recognises how rapidly the brake pedal is applied and automatically provides maximum braking efficiency as long as the brake pedal is depressed. Additionally, the EBA initiates ABS earlier, shortening the stopping distance required.
  • Page 184 4-24 Chapter 4 DRIVING Add on EquIPmEnT SnoW CHAInS Due to lack of clearance, snow chains cannot be fitted to vehicles equipped with the following wheel and tyre configurations: • 245/45R18 18 x 8 • 245/40R19 19 x 8 If these vehicles need to be driven in the snow, the owner should consider changing to the following wheel and tyre configurations: •...
  • Page 185 4-25 Chapter 4 DRIVING Add on EquIPmEnT cont. fITTIng Roo/nudgE BARS If a roo/nudge bar is to be fitted, it is critical that the Holden approved roo/nudge bar be used. Other types must not be fitted. The Holden roo/nudge bar is available from your Holden Dealer and has been compatibility tested with the vehicle’s design, including the Holden airbag system.
  • Page 186 4-26 Chapter 4 DRIVING noTES...
  • Page 187 Fuel Page Fuel..........5-2 Duel fuel LPG .......5-5 Emission control ......5-12 Reducing fuel consumption ..5-13 The asterisk signifies equipment options not in all vehicles, model variants, engine options, optional equipment and Genuine Holden Accessories (and Parts).
  • Page 188 Chapter 5 FUEL fuEL EXHAUST WARNINg – CARBON MONOXIDE POISONINg Exhaust gases can produce carbon monoxide, a dangerous gas, which can cause unconsciousness and even death to both humans and animals. Gases could be inhaled if the exhaust system on your vehicle is faulty. To protect against exhaust gases entering the vehicle, the exhaust system and body should be inspected: •...

  • Page 189: Fuel

    Chapter 5 FUEL fuEL cont. WARNINg – USE OF FUEL CONTAININg ETHANOL When purchasing such fuel, we recommend that the vehicle be operated on fuel containing no more than 10% ethanol. Under no circumstances should fuel containing more than 10% ethanol be used. Use of such fuels may result in engine malfunction, starting and operating difficulties, and materials degradation.
  • Page 190 Chapter 5 FUEL fuEL cont. Fuel cap The fuel cap, under the fuel flap, is a ratchet type cap that is tethered to the vehicle. To open, turn the cap anticlockwise. After refilling, tighten the cap clockwise until a clicking noise is heard and then close the fuel flap.
  • Page 191 Chapter 5 FUEL duAL fuEL LPg EmERgEnCy PRoCEduRES WARNINg • LPG is heavier than air and if not dispersed tends to collect in low-lying areas. Accident or fire • Call the emergency fire services to the scene and keep people away from the vehicle.
  • Page 192 Chapter 5 FUEL duAL fuEL LPg cont.  3. Open the valve box cover  Pull the latch to the upright position. Lift the valve box cover up until it disengages from the tank. Note The valve box cover is tethered to the LPG tank.
  • Page 193 Chapter 5 FUEL duAL fuEL LPg cont. duAL fuEL (LPg) InTRoduCTIon Congratulations on purchasing a Holden ‘Dual Fuel’ vehicle. Not only will you appreciate the savings in fuel costs, but as importantly you will reap the benefit of a fully integrated LPG engine management system.
  • Page 194 Chapter 5 FUEL duAL fuEL LPg cont. LPg REfuELLIng WARNINg • Observe the filling instructions and warnings displayed at the filling station. • Ensure there are no flames or sparks in the vicinity of the vehicle. Note LPG or petrol may be added, regardless of the fuel selected. 1.
  • Page 195 Chapter 5 FUEL duAL fuEL LPg cont. fuEL SELECTIon Changing fuels and starting The fuel selector switch is located below the heater controls on the dashboard. Fuel selection may be done at any time by simply changing the switch to the desired fuel. Note If the vehicle has the default LPG option refer to Default LPG operation further on in this chapter.
  • Page 196 5-10 Chapter 5 FUEL duAL fuEL LPg cont. dEfAuLT LPg oPERATIon The default LPG option is available to customers as an option when purchasing the LPG system and cannot be disabled. This option encourages driving on LPG. Switching between fuels The default LPG fuel selector switch is spring loaded to the LPG position.
  • Page 197 5-11 Chapter 5 FUEL duAL fuEL LPg cont. LPg fuEL gAugE The 4 lights in the change over switch indicate fuel level: • Four lights illuminated full • Three lights illuminated ¾ • Two lights illuminated ½ • One light illuminated ¼...
  • Page 198 5-12 Chapter 5 FUEL EmISSIon ConTRoL The vehicle is fitted with emission control systems, which are designed to reduce the amount of hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx) that are emitted from the engine and fuel system into the atmosphere. Hydrocarbons and oxides of nitrogen, when exposed to sunlight under certain conditions, contribute to photochemical smog.
  • Page 199 5-13 Chapter 5 FUEL REduCIng fuEL ConSumPTIon EngInE To keep the engine in peak mechanical condition, have it serviced regularly in accordance with the maintenance schedule. Refer to Maintenance schedule in the Service/warranty booklet. This ensures items such as the spark plugs, air cleaner and engine idle speed are maintained for minimum fuel usage and peak engine performance.
  • Page 200 5-14 Chapter 5 FUEL noTES...
  • Page 201 Emergencies Page Customer assistance – Australia..........6-2 Customer assistance – New Zealand ........6-3 Flat tyre...........6-4 Changing a flat tyre ......6-5 Spare wheel carrier troubleshooting ......6-14 Towing a disabled vehicle .....6-16 Engine overheating.......6-17 Flat battery........6-20 Fuse replacement ......6-23 Bulb replacement......6-30 The asterisk signifies equipment options not in all vehicles, model variants, engine options, optional equipment and Genuine Holden Accessories (and Parts).
  • Page 202 Chapter 6 EMERGENCIES CuSTomER ASSISTAnCE We want you to be happy with your new vehicle, together with the people you deal with while you have the vehicle. Normally, any problems with the sales, operation, servicing or the validity of original equipment supplied with your vehicle will be handled by your Holden Dealer’s Sales and Service Department.

  • Page 203: Emergencies

    Chapter 6 EMERGENCIES foR nEW zEALAnd HoLdEn oWnERS The information in this Owner’s Handbook applies primarily to Australian Holden vehicles and there may be some differences to the Warranty and Owner Assistance provisions for New Zealand. Applicable details for New Zealand are set out in the Holden Warranty and Owner Assistance Information booklet enclosed in the New Zealand glovebox wallet.
  • Page 204 Chapter 6 EMERGENCIES fLAT TyRE WARNINg • All passengers must be out of the vehicle when it is being jacked. • Do not jack a vehicle with a trailer attached. Remove the trailer first. • Only jack the vehicle on hard, level surfaces. •...
  • Page 205 Chapter 6 EMERGENCIES CHAngIng A fLAT TyRE 1. Park on a hard, level surface, in a safe location, and set the park brake firmly. Switch the hazard warning flashers on. 2. Remove the ignition key and place manual transmissions in reverse gear or automatic transmissions in P (park).
  • Page 206 Chapter 6 EMERGENCIES CHAngIng A fLAT TyRE cont. 6. To remove the tool container, undo and remove the retaining nut. 7. Slide the jack package off the bolt and place next to the wheel to be changed. 8. Remove the jack handle, extension bar, wheel wrench and jack from the container.
  • Page 207 Chapter 6 EMERGENCIES CHAngIng A fLAT TyRE cont. 9. Insert the extension bar into the spare wheel lowering slot. Twist the bar back and forth to engage into the carrier. Note Do not lower the tailgate while the extension bar is in place. VEUD6_062 10.
  • Page 208 Chapter 6 EMERGENCIES CHAngIng A fLAT TyRE cont. 13. From behind the vehicle, grasp the spare wheel and pull it out towards the rear as shown. Note If the spare wheel cannot be manoeuvred to the position shown in step 13, repeat steps 11 and 12. WARNINg Do not get under the vehicle.
  • Page 209 Chapter 6 EMERGENCIES CHAngIng A fLAT TyRE cont. 16. If the wheel trim covers the wheel nuts, remove as follows: • If a full wheel cover is fitted, lever it off with the end of the wheel wrench. • If a centre cap is fitted that covers the wheel nuts, remove it using the end of the wheel wrench.
  • Page 210 6-10 Chapter 6 EMERGENCIES CHAngIng A fLAT TyRE cont. 21. To use the jack handle, kneel down beside the vehicle to the side of the jack. 22. Grasp the hooked fold out section with one hand as shown. 23. With the other hand turn the handle through 180 degrees until it reaches ...
  • Page 211 6-11 Chapter 6 EMERGENCIES CHAngIng A fLAT TyRE cont. WARNINg To fully tighten the wheel nuts, the wrench must be fully extended. 32. Replace any wheel trim or nut cap that was covering the wheel or wheel nuts. Note If a full wheel trim is fitted, the tyre valve must line up with the hole in the wheel trim before refitting.
  • Page 212 6-12 Chapter 6 EMERGENCIES CHAngIng A fLAT TyRE cont. 40. Make sure the wheel is stored securely. Check the security by trying to push and pull  then try to turn  the wheel, as shown. If the wheel moves, use the extension bar and jack handle to tighten the wheel carrier, repeating step 36 to 39.
  • Page 213 6-13 Chapter 6 EMERGENCIES CHAngIng A fLAT TyRE cont. TRoLLEy jACk oR VEHICLE HoIST If using a trolley jack or vehicle hoist to raise the vehicle, it is important that the jack be positioned under the centre of the suspension cross member or hoist pad locations, as shown in the illustration.
  • Page 214 6-14 Chapter 6 EMERGENCIES SPARE WHEEL CARRIER TRouBLESHooTIng Secondary latch system This vehicle has an underbody-mounted wheel carrier assembly, equipped with a secondary latch system. It is designed to stop the spare wheel from suddenly falling off the vehicle if the cable holding the spare wheel is damaged. WARNINg •...
  • Page 215 6-15 Chapter 6 EMERGENCIES SPARE WHEEL CARRIER TRouBLESHooTIng cont. 6. Attach the jack handle to the jack and position the jack lift head under the centre of the wheel, as shown in illustration VEUD6_096. 7. Wind the jack up, by turning the jack handle clockwise, until it contacts the end of the securing cable assembly.
  • Page 216 6-16 Chapter 6 EMERGENCIES ToWIng A dISABLEd VEHICLE WARNINg • Flat tray towing is the only recommended towing procedure. • A slot and rope location is provided to move a bogged or disabled vehicle a short distance or to pull the vehicle onto a flat tray tow truck. •...
  • Page 217 6-17 Chapter 6 EMERGENCIES EngInE oVERHEATIng WARNINg Immediate action is required if the engine overheats. This is indicated by one or more of the following: The temperature gauge needle moving over to the H. • The animated warning Engine Temp Hot appearing on the central display. Refer •...
  • Page 218 6-18 Chapter 6 EMERGENCIES EngInE oVERHEATIng cont. LoW CooLAnT LEVEL If the level is too low, proceed as follows: WARNINg Do not remove the radiator cap if the engine and radiator are still hot. Scalding fluid and steam can be blown out under pressure which could cause serious burns. When the engine has cooled sufficiently, check the coolant reservoir level and radiator level and fill as follows.
  • Page 219 6-19 Chapter 6 EMERGENCIES EngInE oVERHEATIng cont. WARNINg Do not spill coolant on the vehicle’s exterior surfaces as it can damage the paint work. If you do, wash it off immediately. 4. If there is no coolant or the coolant level is low, slowly fill the system through the radiator cap opening with coolant of the correct concentration (refer to Specifications in chapter 8) until full.
  • Page 220 6-20 Chapter 6 EMERGENCIES fLAT BATTERy jumP STARTIng Please read the following warnings and procedure in full before attempting to jump start the vehicle. If, after reading the following procedure, you are still unsure about ‘jump starting’, Holden strongly recommends for your safety and that of the vehicle that you seek the assistance of a suitably trained service technician.
  • Page 221 6-21 Chapter 6 EMERGENCIES fLAT BATTERy cont. Jump starting connection posts • The jump start positive and negative posts are located in the engine bay on the left-hand side of the vehicle. • These posts are used instead of a direct connection to a battery. •...
  • Page 222 6-22 Chapter 6 EMERGENCIES fLAT BATTERy cont. Jump starting procedure Note The battery in both vehicles must have a negative earth and a 12 volt rating. 1. Position the two vehicles so that they are NOT touching. 2. Apply the park brakes. 3.
  • Page 223 6-23 Chapter 6 EMERGENCIES fuSE REPLACEmEnT WARNINg Switch off the ignition and any electrical equipment before changing a fuse. A fuse puller is provided in the cabin and engine compartment fuse panels, which can be used on each of the 3 fuse panels.
  • Page 224 6-24 Chapter 6 EMERGENCIES fuSE REPLACEmEnT cont. BATTERy fuSES And RELAyS The fuse panel is located behind the passenger’s seat to the side of the battery. Lift up the access flap to locate the fuse panel. VEUD6_091...
  • Page 225 6-25 Chapter 6 EMERGENCIES fuSE REPLACEmEnT cont. Battery fuse and relay index Fuses: F1 - REAR SEAT ENTERTAINMENT ....(10A) F2 - AMPLIFIER ......(30A) F3 - NAVIGATION/ TELEMATICS/PHONE ..(10A) F4 - RADIO & INFOTAINMENT .. (15A) F5 - INST/DISP/RFA/DLC ..
  • Page 226 6-26 Chapter 6 EMERGENCIES fuSE REPLACEmEnT cont. CABIn fuSES And RELAyS The fuse panel is located in the left hand side kick panel. Use the slot in the fuse panel cover and slide rearwards to reveal the fuse panel.
  • Page 227 6-27 Chapter 6 EMERGENCIES fuSE REPLACEmEnT cont. Cabin fuse and relay index Circuit breakers: F16 - PHONE/KEY LK/ISRVM/ B1 - WINDOW BATTERY ... (20A) RAIN SENSOR ....(10A) B2 - POWER WINDOWS ... (20A) F17 - SUNROOF ......(20A) B3 - POWER SEATS ....
  • Page 228 6-28 Chapter 6 EMERGENCIES fuSE REPLACEmEnT cont. EngInE ComPARTmEnT fuSES And RELAyS This is the main fuse/relay box. Remove the clip-on cover to gain access. FL10 FL 12 FL11...
  • Page 229 6-29 Chapter 6 EMERGENCIES fuSE REPLACEmEnT cont. Engine compartment fuse and relay index Fuses: F28 - ECM 1 ......... (15A) FL1 - SPARE F29 - EVEN COILS/ INJECTORS ......(20A) FL2 - REAR DEFOG ....(40A) F30 - SPARE FL3 - ABS MOTOR ....... (40A) F31 - SPARE FL4 - BATT MAIN 3 ......
  • Page 230 6-30 Chapter 6 EMERGENCIES BuLB REPLACEmEnT Note If unsure of the bulb replacement process for any of the lamps, please have the work carried out by a suitably trained service technician. noTES WHEn REPLACIng BuLBS • Switch the ignition off and remove the keys. •...
  • Page 231 6-31 Chapter 6 EMERGENCIES BuLB REPLACEmEnT cont. 2. Unclip the air filter box cover and move rearward. Disconnect the air flow meter connector (V8 only). Note When refitting the air filter box cover, ensure that the air filter element and cover are seated correctly.
  • Page 232 6-32 Chapter 6 EMERGENCIES BuLB REPLACEmEnT cont. Front lamp assembly  Front turn signal lamp (PY21W amber bulb).  Headlamp inboard high beam (H9 bulb, 65W).  Headlamp wiring connector. Park lamps (W5W bulb). Headlamp outboard low beam (H7 bulb, 55W). Note Depending on the model variant, the park lamp bulb is in either of the two...
  • Page 233 6-33 Chapter 6 EMERGENCIES BuLB REPLACEmEnT cont. Headlamps – outboard low beam 1. Follow the steps described in section Front lamps previously in this chapter, to gain access to the lamp assembly. 2. Turn the outboard dust cap anti- clockwise and remove. Note Take care not to drop the dust cap into the engine compartment.
  • Page 234 6-34 Chapter 6 EMERGENCIES BuLB REPLACEmEnT cont. Headlamps – inboard high beam 1. Follow the steps described in section Front lamps previously in this chapter to gain access to the lamp assembly. 2. Turn the inboard dust cap anti- clockwise and remove. Note Take care not to drop the dust cap into the engine compartment.
  • Page 235 6-35 Chapter 6 EMERGENCIES BuLB REPLACEmEnT cont. Front park lamps 1. Follow the steps described in section Front lamps previously in this chapter to gain access to the lamp assembly. 2. Remove the outboard low beam dust cover to access the bulb. Note Take care not to drop the dust cap into the engine compartment.
  • Page 236 6-36 Chapter 6 EMERGENCIES BuLB REPLACEmEnT cont. Front turn signal 1. Follow the steps described in section Front lamps previously in this chapter to gain access to the lamp assembly. To aid access, remove the outboard dust cap. Note Take care not to drop the dust cap into the engine compartment.
  • Page 237 6-37 Chapter 6 EMERGENCIES BuLB REPLACEmEnT cont. REAR LAmPS To gain access to the rear turn signal, stop/tail and reverse bulbs: 1. Remove the 6 scrivets and the access  panel Use a flat-blade screwdriver to prise outwards under the head of the centre pin of the scrivet.
  • Page 238 6-38 Chapter 6 EMERGENCIES BuLB REPLACEmEnT cont. Rear lamp assembly  Reverse lamp (P21W bulb).  Stop/tail lamp (P21/5W bulb).  Turn signal lamp (PY21W amber bulb). Rear lamp wiring connector. VEUD6_090 Rear turn signal, stop/tail, reverse 1. Follow the steps described in section Rear lamps previously in this chapter to gain access to the lamp assembly.
  • Page 239 6-39 Chapter 6 EMERGENCIES BuLB REPLACEmEnT cont. numBER PLATE LAmP (W5W BuLB) 1. Push the locking tang at the end of the lamp housing towards the lens and pull the lamp assembly downwards. 2. Remove the bulb holder from the lamp housing by rotating the bulb holder anticlockwise.
  • Page 240 6-40 Chapter 6 EMERGENCIES noTES...
  • Page 241 Weekly checks Page Exterior checks .......7-2 Under bonnet checks......7-7 Under bonnet layout - V6 engine ........7-7 Under bonnet layout - V8 engine ........7-8 Engine oil ........7-9 Automatic transmission fluid level .........7-12 Engine coolant ......7-13 Brake fluid .......7-15 fluid ......7-16 Clutch Power steering fluid ....7-17 Washer fluid ......7-18 Battery ..........7-19...
  • Page 242 Chapter 7 WEEKLY CHECKS ExTERIoR CHECkS mISCELLAnEouS CHECkS As well as taking the vehicle to be serviced, there are a few simple, weekly checks that the owner/operator is recommended to make. These are shown on the following pages. WARNINg • If the engine temperature is high, the cooling fan may remain on for several minutes after switching off the ignition.

  • Page 243: Weekly Checks

    Chapter 7 WEEKLY CHECKS ExTERIoR CHECkS cont. TyRES Air pressure Weekly checking of the air pressure in the tyres (including the spare) ensures your safety, as well as reducing fuel consumption and increasing the life of the tyres. For constant long distance or rough road driving, daily checking is recommended.
  • Page 244 Chapter 7 WEEKLY CHECKS ExTERIoR CHECkS cont. Tyre rotation Front and rear tyres perform different jobs and can wear differently depending on factors such as: • the types of roads driven on, • driving habits, • tyre pressures, • wheel alignment and balance. •...
  • Page 245 Chapter 7 WEEKLY CHECKS ExTERIoR CHECkS cont. VEHICLES fITTEd WITH LoW PRofILE SPoRTS TyRES You have purchased a performance vehicle which has optimally matched low profile tyres fitted to provide you with the best possible ride comfort and running performance. Low profile tyres are expected to experience greater wear than conventional tyres, depending on driving conditions.
  • Page 246 Chapter 7 WEEKLY CHECKS ExTERIoR CHECkS cont. Tyres with a higher speed or load rating are acceptable, provided they are fitted to a suitable rim size. Note New tyres should be fitted in pairs to the front. If replacing only one tyre, it should be paired on the same axle with the least worn of the other three.
  • Page 247 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS undER BonnET LAyouT – V6 EngInE Page  Engine coolant reservoir ...................7-13 Brake fluid reservoir ..................7-15  Clutch fluid reservoir  ..................7-16  Automatic transmission dipstick (4 speed) ............7-12 Engine oil filler cap ....................7-9 ...
  • Page 248 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. undER BonnET LAyouT – V8 EngInE Page  Engine coolant reservoir ...................7-13 Brake fluid reservoir ..................7-15  Clutch fluid reservoir  ..................7-16  Dipstick for engine oil ..................7-9 Engine oil filler cap ....................7-9 ...
  • Page 249 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. EngInE oIL Checking the engine oil level The level is checked with the dipstick. For engine oil dipstick location, refer to Under bonnet layout previously in this chapter. Check the level when the oil is warm, such as when stopping for fuel.
  • Page 250 7-10 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. Engine oil consumption Every internal combustion engine uses a certain amount of oil, especially when running in. The engine is dependent on oil for lubricating critical areas, such as the cylinder walls, pistons, rings and valve stems.
  • Page 251 7-11 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. Measuring oil consumption A simple consumption test can be performed if the driver is concerned by an apparent drop in the oil level. Add sufficient oil to bring the level up to the UPPER mark on the dipstick (avoid overfilling).
  • Page 252 7-12 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. AuTomATIC TRAnSmISSIon fLuId LEVEL (4 SPEEd) The dipstick handle on vehicles fitted with 4-speed automatic transmissions is located at the rear of the engine compartment, on the right side. Refer to Under bonnet layout previously in this chapter for automatic transmission dipstick location.
  • Page 253 7-13 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. EngInE CooLAnT Engine coolant level Check the coolant level at least once a week. The cap for the coolant reservoir is yellow and has the word DEXCOOL marked on the top. Refer to Under bonnet layout previously in this chapter for coolant reservoir location.
  • Page 254 7-14 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. Adding coolant WARNINg Do not spill coolant on the vehicle’s exterior surfaces as it can damage the paint work. If you do, wash it off immediately. Refer to Specifications in chapter 8 for engine coolant specifications and water-to- coolant ratio.
  • Page 255 7-15 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. BRAkE fLuId Brake fluid level WARNINg Brake fluid is poisonous and corrosive and will damage the paint finish of the vehicle if spilt. Check the brake fluid level in the brake fluid reservoir weekly.
  • Page 256 7-16 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. CLuTCH fLuId (manual transmission) Clutch fluid level WARNINg Clutch fluid is poisonous and corrosive and will damage the paint finish of the vehicle if spilt. Check the clutch fluid level in the clutch fluid reservoir weekly.
  • Page 257 7-17 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. PoWER STEERIng fLuId Power steering fluid level Check the level after the vehicle has been driven for a while (at least 20 minutes) so that the fluid is warm. A convenient time is when stopping for fuel. The cold level check should only be used after the engine has not been running for at least 5 hours.
  • Page 258 7-18 Chapter 7 WEEKLY CHECKS undER BonnET CHECkS cont. WASHER fLuId Washer fluid level The washer fluid reservoir has a blue flip top cap. Refer to Under bonnet layout previously in this chapter for washer fluid reservoir location. The container shown supplies water to the front windscreen washer.
  • Page 259 7-19 Chapter 7 WEEKLY CHECKS BATTERy WARNINg • Batteries emit an explosive gas mixture which may be ignited. Therefore, you should keep sparks and flames away from the battery at all times. Never smoke near a battery. • Batteries contain sulphuric acid. If acid contacts skin or clothing, flush immediately with plenty of water.
  • Page 260 7-20 Chapter 7 WEEKLY CHECKS noTES...
  • Page 261 Specifications Page Specifications – V6 engines ...8-2 Specifications – V8 engines ...8-3 General specifications ....8-4 Identification labels ......8-5 The asterisk signifies equipment options not in all vehicles, model variants, engine options, optional equipment and Genuine Holden Accessories (and Parts).
  • Page 262 Chapter 8 SPECIFICATIONS SPECIfICATIonS – V6 EngInES Engine type ALLOYTEC V6 Engine capacity 3564 cc Engine power Please refer to holden.com.au and torque Engine oil Use SAE 5W/30 or 10W/30 API SL/SM specification ILSAC GF-3/GF-4 oil Refill engine 6.5 L approximately (including filter) oil capacity ®...

  • Page 263: Specifications

    Chapter 8 SPECIFICATIONS SPECIfICATIonS – V8 EngInES Engine type GENERATION IV V8 Engine capacity 5967 cc Engine power Please refer to holden.com.au and torque Engine oil Use SAE 5W/30 or 10W/30 API SL/SM specification ILSAC GF-3/GF-4 oil Refill engine 7.6 L approximately (including filter) oil capacity Coolant ®...
  • Page 264 Chapter 8 SPECIFICATIONS gEnERAL SPECIfICATIonS dImEnSIonS (mm) Omega V-series Length 5055 5040 5040 5040 Width - excl. mirrors 1899 1899 1899 1899 Width - incl. mirrors 2100 2100 2100 2100 Height 1497 1480 1480 1480 Wheel base 3009 3009 3009 3009 Overhang - front Overhang - rear...
  • Page 265 Chapter 8 SPECIFICATIONS IdEnTIfICATIon LABELS  LPg ComPLIAnCE PLATE This plate shows the installation date, the plate number, permit number, certificate of compliance number, cylinder (LPG tank) number, Vehicle Identification Number (VIN) and engine number.  CooLIng SySTEm/AIR CondITIonIng LABEL This label shows the warnings for the air conditioning and cooling system as well as information on the air conditioning refrigerant and compressor oil.
  • Page 266 Chapter 8 SPECIFICATIONS IdEnTIfICATIon LABELS cont. ISoVIn PLATES Each vehicle has its own, individual International Standards Organisation Vehicle Identification Number (ISOVIN), which is shown both behind the windscreen on the left side and under the right-hand front seat, under a carpet flap. Sequential production number Plant build code: L = Elizabeth Model year code: 8 = 2008, 9 = 2009, etc...
  • Page 267 Chapter 8 SPECIFICATIONS IdEnTIfICATIon LABELS cont. EngInE numBERS V6 engine The engine number is located at the rear of the engine on the passenger’s side. Note The engine number must be viewed from under the vehicle. V8 engine The engine number is located at the rear of the engine on the passenger’s side.
  • Page 268 Chapter 8 SPECIFICATIONS noTES...

  • Page 269: Tow And Load

    Tow and load Page Loading the vehicle......9-2 Towing ........... 9-5 The asterisk signifies equipment options not in all vehicles, model variants, engine options, optional equipment and Genuine Holden Accessories (and Parts).
  • Page 270 Chapter 9 TOW AND LOAD LoAdIng THE VEHICLE mAxImum fRonT And REAR AxLE LoAdS Do not exceed the maximum axle loads shown in the diagram, including the weight of any fitted accessories. If unsure, the vehicle should be weighed at a weighbridge. This ensures the vehicle’s axles have sufficient strength to carry the total weight and still retain a considerable capacity safety margin to cope with weight transfer as the vehicle brakes, accelerates, corners and goes over bumps.
  • Page 271 Chapter 9 TOW AND LOAD LoAdIng THE VEHICLE cont. noTES on LoAdIng THE VEHICLE • Place heavy objects in the rear load area as far forward as possible against the rear bulkhead. When stacking objects, place the heavier objects at the bottom. Unsecured objects in the rear load area could be thrown forward with great force during heavy braking or in an accident.
  • Page 272 Chapter 9 TOW AND LOAD LoAdIng THE VEHICLE cont. SECuRIng CARgo WARNINg Do not operate the vehicle with the tailgate in the open position as cargo may fall from the load area and the number plate will be obscured from view. Do not use the moulded ribs in the rear load area to secure cargo.
  • Page 273 Chapter 9 TOW AND LOAD ToWIng TRAILERS The word ‘trailer’ is used throughout this section and is intended to include all types of towed vehicles, such as a caravan, boat trailer or any other special purpose trailer. ToWIng The vehicle is designed primarily as a light commercial vehicle, so handling, durability and economy may be affected by towing a trailer.
  • Page 274 Chapter 9 TOW AND LOAD ToWIng cont. Recommended procedure for attaching a trailer If a trailer is hitched to the vehicle, it places a weight on the tow bar. This weight is called the ‘tow bar ball weight’ or ‘tow ball load’. As a general guideline, for single Tow bar ball axle trailers, the ball load should be...
  • Page 275 Chapter 9 TOW AND LOAD ToWIng cont. ToWIng EquIPmEnT Tow load Mandatory equipment Recommended equipment Holden 1,600 kg rated tow bar. Up to 750 kg Holden trailer wiring harness. Holden 1,600 kg rated tow bar. Load distribution hitch. Between 751 kg Holden trailer wiring harness.
  • Page 276 Chapter 9 TOW AND LOAD ToWIng cont. ToWIng PRECAuTIonS • When heavily loading the vehicle or when towing, the tyres should be inflated to the maximum recommended pressure. Refer to Tyres in chapter 7 for tyre placard location and information about tyre pressures. •...

  • Page 277: Cleaning

    Cleaning Page Interior cleaning ......10-2 Exterior cleaning ......10-4 The asterisk signifies equipment options not in all vehicles, model variants, engine options, optional equipment and Genuine Holden Accessories (and Parts).
  • Page 278 10-2 Chapter 10 CLEANING InTERIoR CLEAnIng WARNINg Many cleaning products are toxic, flammable or may damage the interior. When cleaning the interior, avoid volatile cleaners such as acetone, lacquer thinners, enamel reducers, nail polish removers, or cleaners such as laundry soaps, bleaches or reducing agents.
  • Page 279 10-3 Chapter 10 CLEANING InTERIoR CLEAnIng cont. CARPET Thoroughly brush or vacuum the carpet. In many instances the carpet may require no further cleaning. If the carpet is extremely soiled, thoroughly vacuum it to remove loose dirt then, using a good quality velour fabric and vinyl cleaner, clean a small area at a time.
  • Page 280 10-4 Chapter 10 CLEANING ExTERIoR CLEAnIng CARIng foR PAInT WARNINg Do not spill coolant on the vehicle’s exterior surfaces as it can damage the paint work. If you do, wash it off immediately. To help preserve that shiny new vehicle finish, pay special attention to correctly treating those conditions that can damage the paint.
  • Page 281 10-5 Chapter 10 CLEANING ExTERIoR CLEAnIng cont. WASHIng THE VEHICLE The easiest way to keep the paint looking as new is to keep it clean. A wash once a week will keep the vehicle in good condition. However, it must be washed correctly. Note •...
  • Page 282 10-6 Chapter 10 CLEANING ExTERIoR CLEAnIng cont. AIR InTAkES The intake area between the bonnet and windscreen can collect leaves which impairs air flow into the vehicle. Also, the air intake area below the front bumper can collect leaves and road grime, which impairs engine cooling. Refer to Exterior checks in chapter 7.
  • Page 283 10-7 Chapter 10 CLEANING ExTERIoR CLEAnIng cont. PoLISHIng Under normal circumstances the paint does not need polishing to retain its shine. A weekly wash is sufficient. However, the use of a good quality polymer glaze, approximately every 3 months will reduce the effects of road bloom by removing natural contaminants which can build up on the paint.
  • Page 284 10-8 Chapter 10 CLEANING ExTERIoR CLEAnIng cont. ALLoy WHEELS To preserve the original appearance of alloy wheels, keep them clean and free from build up of road dirt. A good quality wheel cleaner can be used for cleaning alloy wheels. Do not use abrasive cleaners on alloy wheels, as the painted surface may be damaged.

  • Page 285: Index

    IndEx Audio system cont. CD changer ABS ..........4-20 operation ...... 1B-16, 1B-38 Accessories CD display ....1B-16, 1B-38 Battery saver ......3-22 CD ejecting ..1B-14, 1B-17, 1B-40 Power sockets ......3-21 CD loading ..1B-14, 1B-17, 1B-40 Retained Accessory Power CD player operation ....1B-14 (RAP) .........
  • Page 286 IndEx cont. Automatic headlamps ....1A-29 Central locking ......2-2, 2-7 Changing a flat tyre ......6-5 Automatic transmission ..... 4-7 Troubleshooting Active select ....1A-13, 4-17 (spare wheel carrier) ....6-14 Fluid level ........7-12 Child restraints........3-7 Gear display ......... 4-8 Child restraint fitting ....
  • Page 287 IndEx cont. Demister, windscreen Emissions ........5-12 with climate control ....1A-41 Engine with manual heater ....1A-36 Overheating ....... 6-17 Specifications ......8-2, 8-3 Dimensions ........8-4 Dimmer, instrument lighting ...1A-28 Starting ........4-6 Dipping headlamps ......1A-30 Temperature warning ....1A-10 Dipstick Engine oil Auto transmission fluid ....
  • Page 288 IndEx cont. Fuel............ 5-2 Help screens........1A-23 Additives ........5-2 High beam ......1A-17, 1A-30 Consumption, reduction ..... 5-13 High beam indicator lamp ....1A-17 Ethanol ......... 5-3 Horn ..........1A-26 Filler flap ........5-3 Fuel cap ........5-4 Identification labels ......8-5 Fumes warning ......
  • Page 289 IndEx cont. Lights cont. Mobile phone ® Hazard lamps ......1A-26 Bluetooth ........1A-46 Headlamps .......1A-28 Charging ........3-21 High/low beam ......1A-30 Connection ....1A-48, 1B-51 Interior lamps ......3-17 MP3. See Audio system. Mudflaps .......... 4-24 Light switch ......1A-28 Night panel mode .....1A-28 Park lamps .......1A-28 New vehicle running-in ......
  • Page 290 IndEx cont. Sports bar ........3-32 Sports tyres ........7-5 Radiator cap ........6-18 Stability control ........ 4-21 Radio. See Audio system. Starting Rear view mirror ..... 3-15, 3-16 Flat battery ......... 6-20 Rear window demister Normal ......... 4-6 with climate control ....1A-42 Steering with manual heater ....1A-35 Power steering fluid ....
  • Page 291 IndEx cont. Turn signals ........1A-30 Warning/reminder indications cont. Tyres Overspeed .......1A-10 Flat, changing ......6-5 Park brake .........1A-9 Grip ..........4-4 Power reduced ......1A-14 Inflation pressure ......7-3 Replace battery in remote key .......1A-15 Replacement and repair ....7-4 Rest reminder ......1A-12 Rotation ........

Table of Contents