Setting Up The Cassette; Automatic Gradation Correction; Adjusting The Image Position - Canon iR C2880 Series Service Manual

2.2.10 Setting Up the Cassette

iR C3380i / iR C3380 / iR C2880i / iR C2880 / iR C3580 / iR C3580i / iR
C3080 / iR C3080i / iR C2380i
1) Press the cassette release button, and slide out the cassette to the front.
2) Check the type of paper that the user uses, check to see that the size con-
figuration switch [1] of the cassette is set to the paper size. As necessary,
change the switch position.
3) Set the paper size dial [2] to suit the size of the paper in question.
[2]
F-2-40
4) Pick the lever [1] of the side guide plate, and move the side guide plate to
the desired position.
5) Shift down the rear guide plate [2] to the right to detach. Adjust the rear
guide plate to suit the appropriate size indicated on the base of the cas-
sette.
F-2-41
6) Attach the cassette size label [1] that matches the selected size of paper to
the front of the cassette.
F-2-42
7) Deposit paper in the cassette; then, slide in the cassette.
8) Perform the same for the other cassette.
9) If a cassette pedestal is used, set it by referring to its Installation Proce-
dure.

2.2.11 Automatic Gradation Correction

iR C3380i / iR C3380 / iR C2880i / iR C2880 / iR C3580 / iR C3580i / iR
C3080 / iR C3080i / iR C2380i
0013-8272
[1]
[1]
0013-8274
For models except ones with DADF, mount the accessory platen cover or
the DADF. When mounting the DADF, be sure to see the installation
procedure for the DADF.
1) Open the copyboard cover/DADF.
2) Clean the host machine copyboard glass.
3) Place A3, A4, 11X17, or LTR paper in the cassette. (See the instructions
on how to set up the cassette.)
4) Press the [Additional Function].
5) Make the following selections: [Adjustment/Cleaning] > [Auto Gradation
Adjustment] > [Full Adjust] > [Test Print 1]
- The test print 1 will be printed out.
6) Place the printout of the test print 1 on the copyboard glass as instructed
on the control panel screen.
7) Close the copyboard cover/DADF.
8) Press [Start Reading].
- The machine reads the printout of the test print 1.
- When a message appears prompting you to remove the test print, remove
the printout of the test print 1 from the copyboard glass.
9) Press [Test Print 2].
- The machine prints out the test print 2.
10) Place the printout of the test print 2 on the copyboard glass as instructed
on the control panel scan.
11) Close the copyboard cover/DADF.
12) Press [Start Reading].
- The machine reads the print out of the test print 2.
- When a message appears promoting you to remove the test print, remove
the printout of the test print 2 from the copyboard glass.
13) Press [Test Print 3].
- The machine prints the test print 3.
14) Place the printout of the test print 3 on the copyboard glass as instructed
on the control panel screen.
15) Close the copyboard cover/DADF.
16) Press [Start Reading].
- The machine reads the printout of the test print 3.
- The machine issues a message to indicate that it has completed full
correction. In response, remove the printout of the test print 3 form the
copyboard glass.
17) Press the Reset key once to end [Additional Function].

2.2.12 Adjusting the Image Position

iR C3380i / iR C3380 / iR C2880i / iR C2880 / iR C3580 / iR C3580i / iR
C3080 / iR C3080i / iR C2380i
"The 2nd side of double-sided copy" indicated later means the 2nd side in
the order of image formation.
In this machine, the 2nd side in the order of image formation at double-
sided copy/printing is equivalent to the 1st side of the document.
1. Adjusting the Margin (1st side; mechanical adjustment)
1) Make a copy using the cassettes 1 and 2 as the source of paper; then, check
to see that the margin on the front side L1 is 2.5±1.5 mm.
[1]
F-2-43
[1] Paper feed direction
<In the case that the cassette 1, or the cassette 2 is out of specification>
1) In the case of the device with the 2-cassette pedestal, detach the cassette
lower right cover [1].
2) Open the cassette upper right cover [2].
Chapter 2
0013-8276
image
2-13