Canon iR C2880 Series Service Manual page 607

Sub item
UI-EPRNT Control unit expansion print screen display restriction
This switch is used to select whether to display the expansion print screen (EFI print screen) on the control unit.
This specification is for users who are customizing the control area so that they have the option of not displaying the
screen.
Additional note
The conventional UI-EXT has been separated into UI-RSCAN and UI-EPRNT to enable them to be controlled
independently.
Settings
0: The expansion print screen is not displayed.
1: The expansion print screen is displayed.
[Factory setting/value after clearing RAM: 1]
UI-WEB Control unit web browser screen display restriction
This switch is used to select whether to display the web browser screen on the control unit.
This specification is for users who are customizing the control area so that they have the option of not displaying the
screen.
Settings
0: The web browser screen is not displayed.
1: The web browser screen is displayed.
[Factory setting/value after clearing RAM: 1]
WEBV-SW Switch to prohibit use of WEBDAV function
By setting this switch to 1 (ON), the WEBDAV function can no longer be used. (The WEBDAV-related displays in the
following are cleared.)
- User mode -> destination table specification settings -> registration of destination -> file -> "WEBDAV" in protocol
- User mode -> "Use chunk division transmission during WEBDAV transmission" among the transmission specification
settings
Reference
WEBDAV is a standard function of the copier, but it is sometimes not used in order to reduce the amount of MEMOry
used.
Settings
0: The WEBDAV function is used.
1: The WEBDAV function is not used.
[Factory setting/value after clearing RAM: 0]
CARD-RNG Setting of number of usable card divisions (number of cards)
This sets the number of divisions (number of cards) for the cards which can be used when the card reader is utilized.
Setting range: 1 to 1000
[Factory setting/value after clearing RAM: 1000]
WUEN-LIV Start time setting after sleep notification from network
This sets the time in 1-second increments (from 10 seconds to 10 minutes) which is to elapse until the sleep mode is next
established when sleep start has been initiated from the network for the copier with no accompanying introduction of
jobs.
Setting range: 10 to 600 (in 1-second increments)
[Factory setting/value after clearing RAM: 15]
COMP-PRT Composite print operation control (image processing memory allocation control)
When a count of 2 or more prints are to be made in page print/ set print/ stamp/ date print/ book binding/ watermark print
(composite print), depending on the memory model (optional configuration) and document size, the memory allocation
method is set to 'print priority' for image processing purposes. This means there is not enough memory for image
processing for Scan, Send Tx (excluding FAX) and PDL entry, and these operations must wait until printing is finished.
In this case, all memory is allocated equally to all jobs so that the operations can be carried out (each a little at a time)
without waiting until printing is finished.
Setting values
0: Print priority
1: Equal allocation
[Factory settings and after RAM clear: 0]
AST-SEL Change advanced smoothing range
Used when adjustments to advanced smoothing effect are felt necessary.
If the smoothing effect is felt to be too strong, even though 'Soft' is selected in the advanced smoothing UI, set this item
to '0'. If the smoothing effect is felt to be too weak, even though 'Strong' is selected in the advanced smoothing UI, set
this item to '3'.
Setting range: 0 to 3
[Factory settings and after RAM clear: 2]
REGM-SEL Change fine line density correction range
Used when adjustments to fine line density for lines and characters in 1200 dpi printing are felt necessary.
If lines and characters are felt to be too faint, even though '+2' is set in the fine line density UI, increase the plus setting
of this item. If lines and characters are felt to be too dark, even though '-2' is set in the fine line density UI, increase the
minus setting of this item.
Setting range: 0 to 4
[Factory settings and after RAM clear: 2]
ORG-LTRR Setting of special sheet sizes which cannot be recognized when ADF is used
This enables images to be formed properly by setting from the service mode the special sheet sizes which cannot be
recognized when documents are fed from ADF.
When ADF has detected LTR-R in a machine for an inch/AB series market, LTR-R is converted into a document size
which has been set in the service mode, and the images are formed using the post-conversion document size.
Settings
0: The document size is converted into LTR-R.
1: The document size is converted into G-LTR-R.
2: The document size is converted into A-LTR-R.
3: The document size is converted into EXECUTIVE-R.
[Factory setting/value after clearing RAM: 0]
COPIER>OPTION>BODY
Description
Chapter 17
level.
2
2
2
2
2
2
2
2
2
17-71