YASKAWA CIMR-DC4A0040AAA Technical Manual page 182

B.2 Parameter Tables
No.
(Address Name
Hex)
o1-02
User Monitor
(501H)
Selection after
Power Up
o1-05
(504H)
LCD Contrast
Control
<7>
o2-01 LO/RE Key
(505H) Function Selection
o2-02 STOP Key Function
(506H) Selection
o2-03 User Parameter
(507H) Default Value
o2-04 Unit Model
(508H) Selection
Operation Selection
o2-06 when Digital
(50AH) Operator is
Disconnected
o2-09
Reserved
(50DH)
o2-21
converter Check
(81AH)
o3-01 Copy Function
(515H) Selection
o3-02 Copy Allowed
(516H) Selection
Cumulative
o4-01
Operation Time
(50BH)
Setting
Cumulative
o4-02
Operation Time
(50CH)
Selection
182
LCD Display
Power-On Monitor
1: Frequency Ref
2: FWD/REV
3: Output Freq
4: Output Current
5: User Monitor
LCD Contrast
o2: Digital Operator Keypad Functions
LO/RE Key
Oper STOP Key
0: Disabled
1: Enabled
User Default Sel
0: No Change
1: Save User Init
2: Clear User Init
Inverter Model #
Oper Discon Det
0: Disabled
1: Enabled
–
US signal check
0: Nomal
1: Start
o3: Copy Function
COPY SELECT
0: COPY SELECT
1: INV→OP READ
2: OP→INV WRITE
3: OP←→INV
VERIFY
Read Allowable
0: Disabled
1: Enabled
o4: Maintenance Monitor Settings
DrvElapsTimeCnt
ElapsTimeCntSet
0: Power-On Time
1: Running Time
YASKAWA ELECTRIC SIEP C710656 06F YASKAWA Power Regenerative Converter - D1000 Technical Manual
Description
Selects the information displayed on the digital operator
when the power is turned on.
1: Output Voltage Reference
2: Output Voltage Feedback
3: Output Current
4: Input Voltage
5: User monitor item set in o1-01
Sets the brightness of the LCD operator.
0: Disabled
1: Enabled. LO/RE key switches between LOCAL and
REMOTE operation.
0: Disabled. STOP key is disabled in REMOTE operation.
1: Enabled. STOP key is always enabled.
0: No change.
1: Set defaults. Saves parameter settings as default values
for a User Initialization.
2: Clear all. Clears the default settings that have been
saved for a User Initialization.
Enter the converter model. Setting required only if
installing a new control board.
Determines the operation when the digital operator is
disconnected.
0: The converter continues operating if the digital operator
is disconnected.
1: A fault is triggered (oPr) and the motor coasts to stop.
–
Sets the operation for Converter Capacity Setting Fault
(oPE01).
Set this parameter to 1 to reset an oPE01 fault without
cycling the power supply.
0: Standard
1: Recheck converter (The parameter returns to 0 after it is
set.)
0: No action
1: Read parameters from the converter, saving them onto
the digital operator.
2: Copy parameters from the digital operator, writing them
to the converter.
3: Verify parameter settings on the converter to check if
they match the data saved on the operator.
0: Read operation prohibited
1: Read operation allowed
Sets the value for the cumulative operation time of the
converter in units of 10 h.
0: Logs power-on time
1: Logs operation time when the converter output is active
(output operation time).
Values
Default: 1
Min.: 1
Max.: 5
Default: 3
Min.: 0
Max.: 5
Default: 1
Min.: 0
Max.: 1
Default: 1
Min.: 0
Max.: 1
Default: 0
Min.: 0
Max.: 2
Default:
Determined by
converter model.
Min.: –
Max.: –
Default: 0
Min.: 0
Max.: 1
–
Default: 0
Min.: 0
Max.: 1
Default: 0
Min.: 0
Max.: 3
Default: 0
Min.: 0
Max.: 1
Default: 0
Min.: 0
Max.: 9999
Default: 0
Min.: 0
Max.: 1