Group Objects; Overview Of Group Objects - ABB i-bus KNX MG/S 11.100.1.1 Product Manual

ABB i-bus ® KNX

Group Objects

8 Group Objects
8.1

Overview of Group Objects

Either one or two Group Objects are enabled per data point, depending on the option selected in the Read
Function and Write Function parameters.
Note
If both the Read Function and Write Function are selected, ETS creates 2 Group Objects (one Status
Group Object and one Control Group Object). However, if only the Read Function or the Write Function
is selected, ETS creates a single Group Object (a Status Group Object for the Read Function or a
Control Group Object for the Write Function).
Function
KNX -> Modbus
Modbus -> KNX
KNX -> Modbus
Modbus -> KNX
KNX -> Modbus
Modbus -> KNX
KNX -> Modbus
Modbus -> KNX
KNX -> Modbus
Modbus -> KNX
KNX -> Modbus
Modbus -> KNX
KNX -> Modbus
Modbus -> KNX
KNX -> Modbus
Modbus -> KNX
KNX -> Modbus
Modbus -> KNX
KNX -> Modbus
Modbus -> KNX
0-no alarm; 1-alarm
Server Address
Register Address
Error text
Note
The Group Objects listed in the overview are the standard Group Objects when the gateway is not
configured. Once configuration/mapping is done, the Group Objects change.
Note about navigation in the PDF: Key combination
'Alt + left arrow' jumps to the previous view/page
Group Object name
D1.1 Control Group Object [DPT_7.001]
D1.1 Status Group Object [DPT_7.001]
D1.2 Control Group Object [DPT_7.001]
D1.2 Status Group Object [DPT_7.001]
D1.3 Control Group Object [DPT_7.001]
D1.3 Status Group Object [DPT_7.001]
D1.4 Control Group Object [DPT_7.001]
D1.4 Status Group Object [DPT_7.001]
D1.5 Control Group Object [DPT_7.001]
D1.5 Status Group Object [DPT_7.001]
D1.6 Control Group Object [DPT_7.001]
D1.6 Status Group Object [DPT_7.001]
D1.7 Control Group Object [DPT_7.001]
D1.7 Status Group Object [DPT_7.001]
D1.8 Control Group Object [DPT_7.001]
D1.8 Status Group Object [DPT_7.001]
D1.9 Control Group Object [DPT_7.001]
D1.9 Status Group Object [DPT_7.001]
D1.10 Control Group Object
[DPT_7.001]
D1.10 Status Group Object [DPT_7.001] 7.001
Status Error alarm [DPT_1.005]
Status Modbus device error [DPT_8.xxx] 8.xxx
Status Modbus register error
[DPT_12.xxx]
Status Error text [DPT_16.001]
Product Manual | EN | MG/S 11.100.1.1 | 9AKK108467A5941 Rev. B 53
Data point type Length Flags
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
7.001 2 bytes C
2 bytes C
1.005 1 bit C
2 bytes C
12.xxx 4 bytes C
16.001 14 bytes C
R W - U
R - T -
R W - U
R - T -
R W - U
R - T -
R W - U
R - T -
R W - U
R - T -
R W - U
R - T -
R W - U
R - T -
R W - U
R - T -
R W - U
R - T -
R W - U
R - T -
R - T -
R - T -
R - T -
R - T -