ADTRAN SMART/RG SR501n User Manual
  1. Manuals
  2. Brands
  3. ADTRAN Manuals
  4. Gateway
  5. SMART/RG SR501n
  6. User manual

ADTRAN SMART/RG SR501n User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
501 SE Columbia Shores Boulevard, Suite 500
Vancouver, Washington 98661 USA
+1 360 859 1780 / smartrg.com
/ Gateway User Manual
Model: SR501
Release 1.3
March 2020
Firmware Version 2.6.2.4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SMART/RG SR501n and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ADTRAN SMART/RG SR501n

Summary of Contents for ADTRAN SMART/RG SR501n

  • Page 1 501 SE Columbia Shores Boulevard, Suite 500 Vancouver, Washington 98661 USA +1 360 859 1780 / smartrg.com / Gateway User Manual Model: SR501 Release 1.3 March 2020 Firmware Version 2.6.2.4...

  • Page 2: Table Of Contents

    QoS Config FCC - Part 68 Supported DSCP Values REN (RINGER EQUIVALENT NUMBERS) QoS Queue Config STATEMENT QoS Classification IC-CS03 statement QoS Port Shaping FCC Statement Routing FCC Radiation Exposure Statement SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2019...
  • Page 3 Table of Contents Canada Statement 5GHz Revision History SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2019...

  • Page 4: Welcome

    Copyright and Trademarks Copyright © 2020 by SmartRG, Inc., an ADTRAN company. Published by SmartRG, Inc. All rights reserved. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, trans- lated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, pho- tocopying, manual, or otherwise, without the prior written permission of SmartRG, Inc.

  • Page 5: Disclaimer

    This publication is subject to change without notice. Any trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 6: Getting Familiar With Your Gateway

    Below is a diagram of how to install your SR501 gateway. This information is also in the Quick Start Guide enclosed with your gateway. Phone jack ON/OFF Power Reset ETH The ports depicted in this example are described below. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 7: Buttons

    20 or more seconds Changes the POWER LED to red and the gateway enters CFE mode which is a state associated with performing firmware updates via Internet browser. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 8: Installing Your Smartrg Gateway

    For in-depth "how-to" information for specific scenarios, look at the knowledge base found on our support web site. Access to this site is restricted to SmartRG customers and partners. Do not share links to this site with your subscribers. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 9: Device Info

    Device Info summary page appears. This page displays details about the hardware and software associated with your gateway. In addition, the current status of the WAN connection (if present) is shown. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 10: Wan

    The state of NAT. Options are Enabled and Disabled. Firewall The state of the Firewall. Options are Enabled and Disabled. Status The status of the WAN connection(s). Options are Disconnected, Unconfigured, Con- necting, and Connected. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 11: Statistics

    Field Name Description Interface LAN interface. Received & Transmitted columns Bytes Number of packets in bytes. Pkts Number of packets. Errs Number of error packets. Drops Number of dropped packets. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 12: Wan Service

    In the left navigation bar, click Device Info > Statistics > xTM. The Interface Statistics page appears. To reset these counters, click Reset near the bottom of the page. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 13: Xdsl

    On this page, you can view the DSL statistics for your gateway. All xDSL (VDSL or ADSL) interfaces configured for your SmartRG gate- way are included. The terms and their explanations are derived from the relevant ITU­ - T standards and referenced accordingly. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 14 Start. Options range from 1 second to 360 seconds. The default is 20 seconds. The test transfers idle cells containing a known pattern and compares the received data with this known pattern. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 15 Signal-to-Noise Ratio Margin (SNRM) to be equal or above the SNR Target Margin BER not to exceed the highest BER configured for one (or more) latency paths Latency not to exceed the highest latency configured for one (or more) latency paths SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 16 The PMS-TC delay in milliseconds of the current latency path (or the lowest latency path when running dual-latency paths). INP (DMT symbol) The input level for DMT-managed DSL environments. (End of DSL-specific field group) Super Frames The number of xDSL OH Frames transmitted/received. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 17: References

    (1999), Asymmetric digital subscriber line (ADSL) transceivers. ITU-T Recommendation G.992.3 (2005), Asymmetric digital subscriber line transceivers 2 (ADSL2). ITU-T Recommendation G.997.1 (2006), Physical layer management for digital subscriber line (DSL) transceivers. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 18: Route

    (For IPv6 only) Next hop IP address. Subnet Mask Subnet mask for the gateway. Flag Status of the flags. See detailed descriptions above the tables. Metric Number of hops required to reach the default gateway. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 19: Arp

    The DHCP page displays a list of locally connected LAN hosts and their DHCP lease status, which are directly connected to the SmartRG Gateway via a LAN Ethernet port. In the left navigation bar, select Device Info > DHCP. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 20: Dhcpv6

    On this page, you can view the host name, the IP address assigned by the DHCPv6 server, and the MAC address corresponding to the IP address. In the left navigation bar, select Device Info > DHCPv6. The following screen appears. The fields on this page are explained in the following table. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 21: Vpn

    Acceptable IP addresses defined for the LAN side. Remote-side Addresses Acceptable IP addresses defined for the WAN side. Enabled Indicates whether the tunnel is enabled or disabled. Connection State Indicates whether the tunnel connection is active or inactive. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 22: Advanced Setup

    Note: Devices (routers) on both ends of the connection must support ATM / PVC. 1. In the left navigation bar, click Advanced Setup > Layer2 Interface > ATM Interface and then click Add. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 23 ATM path. This setting works with the VCI. Each individual DSL circuit must have a unique VPI/VCI combination. String limits are: 0-255. Enter a Virtual Channel Identifier. A VCI is a 16-bit identifier that has a unique channel. Options are: 32-65535. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 24 This cat- egory is commonly used in networks with compressed video traffic. Minimum Cell Rate Minimum allowable rate (cells per second) at which cells can be sent on a ATM net- SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 25: Ptm Interface

    On this page, you can configure a PTM interface for your gateway. 1. In the left navigation bar, click Advanced Setup > Layer2 Interface > PTM Interface and then click Add. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 26 Weighted Round Robin: Packets are accessed in a round robin style. Classes can be assigned. Weighted Fair Queuing: Packets are assigned to a specific queue. Default Queue Weight Enter a default weight of the specified queue. Options are: 1-63. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 27 The shaping rate for the specified queue. Options are: 1-0 Kbps. The default is -1 (no Rate shaping). Default Queue Shaping The maximum rate at which traffic can pass through the queue. Options are 1600 or Burst Rate greater. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 28: Wan Service

    There are several parts to configuring a PPP over Ethernet WAN service. You will progress through several pages to complete the configuration. 1. In the left navigation bar, click Advanced Setup > WAN Service and then click Add. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 29 Options are 0 - 4094. The default is -1 (disabled). VLAN ID For tagged service, enter values in this field and the 802.1P Priority field. For untagged service, enter -1 (disabled) in this field and the 802.1P Priority field. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 30 Select VLAN TPID Select the TPID for this VLAN. Options are 0x8100 , 0x88A8 , and 0x9100 . Internet Pro- Select the IP version. Options are IPv4 Only , IPv4&IPv6 (Dual Stack) , and IPv6 Only . tocol Selection SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 31 5. Click Next. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 32 ) Enable IPv6 Unnumbered Model Select to allow your gateway to process IP packets without configuring a unique IP address. This works by “borrowing” an IP address from another interface. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 33 MLD Multicast section Enable MLD Multicast (Available only for IPv6 environments) Click to enable MLD multicast. Used by IPv4 hosts to Proxy report multicast group memberships to any neighboring multicast routers. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 34 8. Select the interface used as a default gateway for the PPP service being created and click the arrows to move your selection from left to right or from right to left. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 35 11. Alternatively, you can enter static DNS IP addresses in the Use the following Static DNS IP address section. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 36: Ip Over Ethernet

    IP over Ethernet There are several parts to configuring a IP over Ethernet WAN service. You will progress through several pages to complete the con- figuration. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 37 Advanced Setup > WAN Service and then click Add. The following page appears. 2. Select the Layer2 interface to use for the WAN service and click Next. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 38 Options are IPv4 Only, IPv4&IPv6 (Dual Stack), and IPv6 Only. The default is IPv4 Only. Note: When selecting IPV4&IPV6 or IPV6, the subsequent options presented will change accordingly. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 39 5. Click Next. The following page appears.  SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 40 If using the Advanced DMZ feature, you can enter a secondary LAN IP address for the gateway. The default is 255.255.255.0. IPv6 settings The following fields appear when either IPv6 Only or IPv4&IPv6 (Dual Stack) network protocols are selected on SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 41 /64 is used. WAN Next-Hop IPv6 Enter the IP address of the next WAN in the group. This address can be either a local address link or a global unicast IPv6 address. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 42 Internet normally, you need to add a route on the uplink equipment. Failure to do so will cause access to the Internet to fail. The fields on this page are explained in the following table. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 43 Enable MLD Multicast Source ticast source. Use Base MAC Address Use SmartRG Devices Base (Primary) MAC address. When unchecked, a unique MAC per on this WAN interface service is assigned. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 44 10. Select the interface used as a default gateway for the PPP service being created and click the arrows to move your selection from left to right or from right to left. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 45 Obtain IPv6 DNS info from a WAN interface: Select a Interface. Use the following Static IPv6 DNS address: Enter the Primary IPv6 DNS server address and, if desired, enter a Sec- ondary IPv6 DNS server address. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 46: Bridging

    Back to step through the pages in reverse order to make any necessary alterations. Bridging Before you can configure a bridge WAN service, you must create the related ATM interface. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 47 Add. The following page appears. 2. Select an ATM interface for the WAN service and then click Next. The following page appears. 3. Select Bridging. The Multicast Source fields appear. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 48 For untagged service, enter -1 (disabled) in this field and in the 802.1P Priority field. ( Optional ) Select the TPID for this VLAN. Options are 0x8100 , 0x88A8 , and 0x9100 . Select VLAN TPID SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 49 5. Click Next. The summary page appears indicating that your Bridging WAN setup is complete. 6. Review the summary and either click Apply/Save to commit your changes or click Back to step through the pages in reverse order to make any necessary alterations. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 50: Lan

    On the Local Area Network (LAN) Setup page, you can configure the router’s local IP addresses, subnet mask, DHCP behavior and other related LAN side settings for your gateway. 1. In the left navigation bar, click Advanced Setup > LAN. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 51 IP address will be leased. Static IP Lease List Specify a literal, static IP address to be associated with a specific MAC Address of one of your LAN host devices. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 52 IP address and Subnet mask to support a second, simultaneous LAN, i.e., the net mask for LAN primary LAN might be defined as 192.168.0.1 and this secondary LAN defined as 192.168.2.1. interface SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 53: Ipv6 Autoconfig

    IPV6 address to assign as the gateways Local LAN IPV6 address and prefix length. Prefix length is required. IPv6 LAN Applications section Enable DHCP v6 This option enables the DHCP v6 feature on the LAN. Server SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 54: Ethernet Config

    Options are Disable and Enable . LAN Multicast Ethernet Config On the Ethernet Port Configuration page, you can set the speed and duplex mode for each of the Ethernet ports. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 55 Ethernet auto negotiation with the NIC of the LAN host. Note: For 1000 BaseT connections, always select Auto. 3. Click Save/Apply to commit your changes. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 56: Nat

    On this page, you can configure the virtual server settings for your gateway. 1. In the left navigation bar, select Advanced Setup > NAT. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 57 Select a Service list, you can enter a unique name for the application in this field. Server IP Enter the IP address of the LAN client where the service is hosted. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 58: Port Triggering

    The gateway allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the Open Ports. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 59 Enter the starting number of the range of available outgoing trigger ports. Options are: 1 - 65535. Trigger Port End Enter the end number of the range of available outgoing trigger ports. Options are: 1 - 65535. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 60: Dmz Host

    1. In the left navigation bar, click Advanced Setup > > Host. The following page appears. 2. Enter the DMZ Host IP Address. 3. Click Save/Apply to commit your change. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 61: Security

    Options are IPv4 and IPv6. The default is IPv4. If you select IPV6, both the Source and Destination IP address must be specified in IPV6 format. The following is an IPV6-compliant, hexadecimal address: 2001:0DB8:AC10:FE01:0000:0000:0000:0001. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 62: Ip Filtering - Incoming

    On this page, you can add an incoming filter when refusal of data from the WAN to the LAN is desired. 1. In the left navigation bar, click Advanced Setup > Security > IP Filtering > Incoming and then click Add. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 63 Click to apply this rule to all WAN interfaces or only certain types. Options are Select All or the interfaces defined for your network. The default is Select All . SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 64: Mac Filtering

    The current/active policy type that is in place. Options are FORWARD and BLOCKED . Adding a MAC Filtering Rule You cannot edit rules but you can add new ones and then remove the obsolete ones. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 65: Parental Control

    In this section, you can configure the Parental Control features of your SmartRG gateway to restrict Internet access to certain hours and to certain URLS. Time Restriction On this page, you can restrict Internet access to particular days and specific times for each device that accesses your gateway. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 66 Start Time Blocking / End Enter the range of time that the devices listed above are restricted from access to the Time Blocking Internet. Use 24-hour clock notation (00:00 - 24:00). SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 67: Url Filter

    In this section, you can configure QoS settings including traffic queues, classifications (rules) and port shaping. Note: Before proceeding, make sure that the necessary WAN service has been configured with the appropriate Priority setting. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 68: Qos Config

    Differentiated Services Code Point (DSCP) Mark classification value to be used. The default is No Change(-1). For a list of supported values, see "Supported DSCP Values". 4. Click Apply/Save to save your settings. Supported DSCP Values SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 69: Qos Queue Config

    2. In the Name field, type a descriptive name for this queue. 3. In the Interface field, select the Layer 2 interface to be associated for this queue. Additional fields appear. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 70 Options are 1600 bytes or greater. ( Applicable for PTM and Dynamic WAN interfaces only ) Select the priority for the PTM PTM Priority interface. Options are Low and High . SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 71: Qos Classification

    2. Fill in the fields, using the information in the table below. 3. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 72 Specify Classification Results section Specify Egress Interface Select the egress interface for this rule. Options are the interfaces already configured. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 73: Qos Port Shaping

    Enter the data rate for packets on the specified Interface. Options are: 1 - 1,000,000 Kbps. The default is -1 (no shaping). Burst Size (bytes) Enter the burst size to be applied to packets in the defined queue. Options are 1600 bytes or greater. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 74 Egress Shaping Rate field, the value in this field is ignored. Enter data rate for policing incoming packets in the defined queue. The default is -1 (no Ingress Policing Rate (Kbps) policing). SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 75: Routing

    Move the highest priority interface first, followed by the next highest priority interface, and so on. 3. (Optional) In the Selected WAN Interface field, select an IPv6 interface. 4. Click Apply/Save to commit your changes. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 76: Static Route

    On this page, you can configure similar policies. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 77: Rip (Routing Information Protocol)

    (maximum of 15) allowed in order to prevent routing loops. This can sometimes limit the size of networks where RIP can be suc- cessfully employed. Note: This feature applies only to IPoE configurations. On this page, you can configure the RIP settings. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 78 Select the operation mode. Options are: Active: This mode listens and advertises routes. Passive: This mode listens only. It does not advertise routes. Enabled Select to employ RIP on the displayed interface. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 79: Dns

    2. (Optional) Select DNS Server interfaces by moving them from left to right or right to left by clicking the arrows. The options for obtaining the DNS information from a WAN interface are selected by default. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 80: Dynamic Dns

    The fields on this page are explained in the following table. Field Name Description D-DNS provider Select a dynamic Domain Name Server provider. Hostname Enter the hostname of the dynamic DNS server. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 81: Static Dns

    The fields on this page are explained in the following table. Field Name Description Hostname Enter the hostname of the client computer. IP Address Enter the IP address of the DNS server client uses to assist in resolving domain names. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 82: Dsl

    Caution: Altering these settings unnecessarily can result in the gateway being unable to attain DSL synchronization. 1. In the left navigation bar, click Advanced Setup -> DSL. The following page appears. 2. Modify the settings as needed. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 83 The RJ11 connector has four contacts. The center pair of pins is DSL1. The outer pins are the con- Pair/Outer Pair tacts for DSL2. Select which pair should be used. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 84: Advanced Settings

    Advanced settings 1. To configure the test mode, click Advanced Settings on the Advanced Setup > page. The following page appears. 2. Click Apply to place the gateway in test mode. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 85 The DSL PHY attempts to establish a connection as in Normal mode, but once the connection is up, it does not retrain even if the signal is lost. Puts the DSL modem in the L3 power state. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 86: Upnp

    1. In the left navigation bar, select Advanced Setup > UPnP. The following page appears. 2. To disable this option, click Enable UPnP to clear the box. 3. Click Apply/Save to commit your changes. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 87: Dns Proxy

    Host name Domain Name fields appear. 3. Enter the host name of the broadband router and the domain name of the LAN network. 4. Click Apply/Save to commit your changes. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 88: Interface Grouping

    You can create an interface group to map local interfaces to WAN interfaces. A typical application for this feature is assigning IPTV STBs to a WAN interface. 1. In the left navigation bar, click Advanced Setup > Interface Grouping and then click (below the table). The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 89 Important: If a vendor ID is configured for a specific client device, make sure to reboot the client device attached to the gate- way to allow it to obtain an appropriate IP address. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 90: Ip Tunnel

    IPv6inIPv4 On this page, you can configure the IPv6inIP4 settings. 1. In the left navigation bar, click Advanced Setup > IP Tunnel and then click Add. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 91: Ipv4Inipv6

    Interface, enter the appropriate value for AFTR (Address Family Transition Router). To configure this setting automatically, select Automatic. The AFTR field is hidden. 5. Click Apply/Save to commit your changes. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 92: Ipsec

    Phase 1 and Phase 2 specific parameters. For detailed information about these settings, see "Advanced IKE Settings". 4. Click Apply/Save to commit your changes. The fields on this page are explained in the following table. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 93 Enter the subnet mask or prefix length for IP address entered for remote access. The default is 255.255.255.0 . Remote ID Type Select the type of ID for the remote VPN. Options are Default, Domain, and E- Mail. The default is Default. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 94: Advanced Ike Settings

    Enter the hex value for the selected authentication algorithm. Enter the hex value for the service provider interface (SPI). The default is 101 . Advanced IKE Settings You can configure advanced IKE settings if desired. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 95: Certificate

    For additional info regarding Public Key Infrastructure (PKI), refer to ITU-T X.509. 1. In the left navigation bar, click Advanced Setup > Certificate > Local and then click Create Certificate Request. The fol- lowing page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 96 Select the country or region in which this certificate will be employed. 4. To import a certificate and the corresponding private key, on the Advanced Setup > Local Certificates page, click Import Cer- tificate. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 97: Trusted Ca

    On this page you import and store up to four trusted certificates. Trusted Certificates are used to identity other gateways to your gateway as a trusted source. 1. In the left navigation bar, click Advanced Setup > Certificate > Trusted CA and then click Import Certificate. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 98: Power Management

    Trusted CA landing page. Click this button to remove the current certificate and replace it with a new one. Power Management Note: This feature is not currently supported. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 99: Multicast

    Add. Note: For the IGMP list, the Group Address must be between 244.x.x.x and 239.x.x.x. For the MLD table, the Group Address must be a valid IPv6 address. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 100 Enter the value representing the complexity of the query. The greater the value, the more robust the query. Options are 2 - 7. The default is 2. Maximum Multicast Enter the maximum number of groups allowed. The default is 25. Groups SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 101 Select whether the IGMP proxy removes group members immediately without sending a query. Options are: Enabled: Group members are removed immediately. This is the default. Disabled: Group members are removed after a query is sent and a response received. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 102: Diagnostics

    Repeat steps 2-4 for each connection. Ethernet OAM On this page, you can view diagnostics regarding your VDSL PTM or Ethernet WAN connection. Fault Management is compliant with IEEE 802.1ag for Connectivity Fault Management. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 103 3. To enable Ethernet Service OAM (802.1ag/Y.1731): a. Click the Enabled checkbox. Additional fields appear showing values for 802.1ag. To configure Y.1731, click the Y.1731 radio button. The page refreshes. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 104 Click to enable automatic reporting of events. Variable Retrieval Click to enable on-demand link diagnostics, including bit-error-rate approximation. Link Events Click to enable reporting of critical conditions that may cause link failure. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 105: Ping Host

    On this page you can ping a server by host name or IP address. 1. In the left navigation menu, click Diagnostics Tools > Ping Host. The following page appears. 2. Enter the host name or IP address. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 106: Trace Route To Host

    Host. The following page appears. 2. Enter the host name or IP address that you want to trace. 3. Click Trace Route to Host. The details of the trace appear on the page. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 107: Management

    Otherwise, every new backup file overwrites the existing backup file. Update On this page, you can restore previously backed-up gateway settings. Both current and default settings can be managed here. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 108: Restore Default

    1. In the left navigation bar, click Management > Settings > Restore Default. The following page appears. 2. Click Restore Default Settings. The gateway is rebooted and the default settings overwrite the previous settings. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 109: System Log

    Log. The following page appears. 2. To view the contents of the system log, click View System Log. The System Log details page appears. 3. To update the displayed entries, click Refresh. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 110: Security Log

    To record events in the local memory of your SmartRG gateway, select Local or Both. c. Click Apply/Save to save your changes. Security Log The security log contains a history of events related to sensitive access to the gateway. Logged events include: SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 111: Management Server

    SmartRG gateways support TR-069-based standards for remote management. The TR-069 client page is preset with default con- nection parameters and generally only needs to be enabled, pointed to the ACS URL, and any required ACS credentials entered. SmartRG products can accommodate several ACS products, including: SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 112 The fields on this page are explained in the following table. Note: Please consult with your ACS vendor for any specific connection request requirements impacted by the following set- tings. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 113 ACS. The default is Any_WAN - IPv4. client 4. (Optional) You can configure the gatway's client Connection Request mechanism which is used by your ACS for communication with subscriber gateways. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 114: Stun Config

    On this page, when a STUN server is present within the infrastructure of the Service Provider, you can configure this gateway with the connectivity specifics for that server. 1. In the left navigation bar, click Management > Management Server > STUN Config. The STUN Configuration page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 115 STUN Server Password The password by which the modem authenticates the above username to the STUN infrastructure. Maximum length is 256 characters. Special characters are valid. The value will be hidden. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 116: Internet Time

    On this page, you can configure the gateway to synchronize its time with the Internet time servers. This feature is enabled by default. 1. In the left navigation bar, click Management > Internet Time. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 117: Access Control

    Each account can be customized to grant access privileges to specific pages in the interface. This is par- ticularly useful when an ISP wishes to limit access for subscribers, yet grant full access for technical support and on-site installation personnel. Add an Account SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 118 1. In the left navigation bar, click Management > Access Control > Accounts. The following page appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 119 4. Select the features that you want this user to access. If you select a category, the subordinate boxes are also selected. For example, if you select Support Tools, Port Mirroring Factory Reset are selected as well. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 120: Modify Or Delete An Account

    To delete the account, click Delete Account. A confirming message appears. Click OK. Your changes are implemented immediately. Default Passwords USER PASSWORD admin admin support support user user IDH7iw@ibRsPOIBa SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 121: Services

    GUI, this column may be read-only. Note: ICMP is an always-enabled service by default and has no checkbox. If a WAN service is configured for your gateway, select the services enabled on the WAN SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 122: Passwords

    On this page, you can create and manage access control lists to control inbound access to specific IP addresses. 1. In the left navigation bar, click Management > Access Control > Access List. The following page appears, showing any addresses already configured for managed access. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 123: Logout Timer

    Remove. The list is updated. Logout Timer On this page, you can define the maximum time that a session can remain open before the gateway logs out. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 124: Update Software

    2. Follow the on-page instructions. When the update has completed, the gateway reboots. Reboot Occasionally, troubleshooting measures may require that the gateway be rebooted. On this page, you can reboot your gateway. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 125 1. In the left navigation bar, select Management > Reboot. The following page appears. 2. Click Reboot. Your gateway is rebooted and you must log in again if you want to make further changes. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 126: Logging Out

    Logging Out 1. To log out of your gateway, click Logout in the left navigation menu. The logout page appears. 2. Click the Logout button. A success message appears. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 127: Appendix C: Fcc Statements

    If you have questions about what will disable alarm equipment, consult your telephone com- pany or a qualified installer. This product meets the applicable Industry Canada technical specifications. / Le présent matériel est conforme aux specifications techniques applicables d’Industrie Canada. IC-CS03 statement SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

  • Page 128: Fcc Statement

    This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 129 Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. 5GHz 5150-5250 MHz band is restricted to indoor operations only. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...
  • Page 130 REVISION DATE CHANGES March 2020 Updated for SmartRG firmware release 2.6.2.4. September 2019 Updated for firmware release 2.6.2.3. September 2019 Updated for firmware release 2.6.2.2. December 2016 Initial release of document. SmartRG Inc., an ADTRAN company. All Rights Reserved. © 2020...

This manual is also suitable for:

Smart/rg sr501

Table of Contents