YASKAWA BACnet/IP JOHB-SMP3 Technical Manual page 20

6 Related Drive Parameters
No.
Name
(Hex.)
F7-06 Subnet Mask 2
(03EA)
F7-07 Subnet Mask 3
(03EB)
F7-08 Subnet Mask 4
(03EC)
F7-09 Gateway Address 1
(03ED)
F7-10 Gateway Address 2
(03EE)
F7-11 Gateway Address 3
(03EF)
F7-12 Gateway Address 4
(03F0)
F7-13 Address Startup Mode
(03F1)
F7-14 Duplex Mode Selection
(03F2)
20
Note:
• This parameter is only effective when F7-13 = 0 [Address Mode at Startup = Static].
• All IP Addresses must be unique.
• You must cycle power to the drive for the changes to take effect. For non-Z1000U drives,
setting F6-15 = 1 [Comm. Option Parameters Reload = Reload Now] enables
communication OPT parameter changes without turning on the power again.
Sets the static/fixed Subnet Mask. Sets the second most significant octet.
Note:
• This parameter is only effective when F7-13 = 0 [Address Mode at Startup = Static].
• All IP Addresses must be unique.
• You must cycle power to the drive for the changes to take effect. For non-Z1000U drives,
setting F6-15 = 1 [Comm. Option Parameters Reload = Reload Now] enables
communication OPT parameter changes without turning on the power again.
Sets the static/fixed Subnet Mask. Sets the third most significant octet.
Note:
• This parameter is only effective when F7-13 = 0 [Address Mode at Startup = Static].
• All IP Addresses must be unique.
• You must cycle power to the drive for the changes to take effect. For non-Z1000U drives,
setting F6-15 = 1 [Comm. Option Parameters Reload = Reload Now] enables
communication OPT parameter changes without turning on the power again.
Sets the static/fixed Subnet Mask. Sets the fourth most significant octet.
Note:
• This parameter is only effective when F7-13 = 0 [Address Mode at Startup = Static].
• All IP Addresses must be unique.
• You must cycle power to the drive for the changes to take effect. For non-Z1000U drives,
setting F6-15 = 1 [Comm. Option Parameters Reload = Reload Now] enables
communication OPT parameter changes without turning on the power again.
Sets the static/fixed Gateway address. Sets the most significant octet.
Note:
• This parameter is only effective when F7-13 = 0 [Address Mode at Startup = Static].
• All IP Addresses must be unique.
• You must cycle power to the drive for the changes to take effect. For non-Z1000U drives,
setting F6-15 = 1 [Comm. Option Parameters Reload = Reload Now] enables
communication OPT parameter changes without turning on the power again.
Sets the static/fixed Gateway address. Sets the second most significant octet.
Note:
• This parameter is only effective when F7-13 = 0 [Address Mode at Startup = Static].
• All IP Addresses must be unique.
• You must cycle power to the drive for the changes to take effect. For non-Z1000U drives,
setting F6-15 = 1 [Comm. Option Parameters Reload = Reload Now] enables
communication OPT parameter changes without turning on the power again.
Sets the static/fixed Gateway address. Sets the third most significant octet.
Note:
• This parameter is only effective when F7-13 = 0 [Address Mode at Startup = Static].
• All IP Addresses must be unique.
• You must cycle power to the drive for the changes to take effect. For non-Z1000U drives,
setting F6-15 = 1 [Comm. Option Parameters Reload = Reload Now] enables
communication OPT parameter changes without turning on the power again.
Sets the static/fixed Gateway address. Sets the fourth most significant octet.
Note:
• This parameter is only effective when F7-13 = 0 [Address Mode at Startup = Static].
• All IP Addresses must be unique.
• You must cycle power to the drive for the changes to take effect. For non-Z1000U drives,
setting F6-15 = 1 [Comm. Option Parameters Reload = Reload Now] enables
communication OPT parameter changes without turning on the power again.
Selects how the option address is set.
0 : Static
1 : [Not Used/No Function] BOOTP
2 : DHCP
Note:
• You must cycle power to the drive for the changes to take effect. For non-Z1000U drives,
setting F6-15 = 1 [Comm. Option Parameters Reload = Reload Now] enables
communication OPT parameter changes without turning on the power again.
• The host controller will assign the IP addresses when F7-13 = 1 or 2.
Sets duplex mode settings (Port 1 (CN1A)/Port 2 (CN1B)).
0 : Half/Half (Half Duplex/Half Duplex)
1 : Auto/Auto (Auto Negotiation/Auto Negotiation)
2 : Full/Full (Full Duplex/Full Duplex)
3 : Half/Auto (Half Duplex/Auto Negotiation)
4 : Half/Full (Half Duplex/Full Duplex)
5 : Auto/Half (Auto Negotiation/Half Duplex)
6 : Auto/Full (Auto Negotiation/Full Duplex)
7 : Full/Half (Full Duplex/Half Duplex)
8 : Full/Auto (Full Duplex/Auto Negotiation)
Description
YASKAWA SIEP C730600 0MA BACnet/IP Technical Manual
Default
(Range)
255
(0 - 255)
255
(0 - 255)
0
(0 - 255)
192
(0 - 255)
168
(0 - 255)
1
(0 - 255)
1
(0 - 255)
2
(0 - 2)
1
(0 - 8)