Icom FP-561 Instruction Manual page 68

5
INITIAL SETTING AFTER INSTALLATION
| COMPASS IND
DATUM
BEARING
COMPASS IND
TIME REF
OFFSET TIME
| TIME REF
BEARING
COMPASS IND
TIME REF
OFFSET TIME
SPEED DATA
SPEED ADJ
| OFFSET TIME
SETTING
AUTO GAIN
DRAFT ADJ
TEMP ADJ
DATUM
BEARING
COMPASS IND
TIME REF
OFFSET TIME
SPEED DATA
SPEED ADJ
NMEA OUT
BOD OUT
ADJ
CANC
CLR
| SPEED DATA
TIME REF
OFFSET TIME
SPEED DATA
SPEED ADJ
NMEA OUT
| SPEED ADJ
SETTING
AUTO GAIN
DRAFT ADJ
TEMP ADJ
DATUM
BEARING
COMPASS IND
TIME REF
OFFSET TIME
SPEED DATA
SPEED ADJ
NMEA OUT
BOD OUT
ADJ
CANC
CLR
65
This item allows you to make a selection between two options on graphic
indication on the navigation monitor screen:
• NOR:
123
TRUE MAG
• REVS:
NOR REVS
LOCAL GMT
+ 9 : 00
This item allows you to make a selection between two options on Time indi-
cation on the navigation monitor screen:
• LOCAL:
TRUE MAG
• GMT:
NOR REVS
LOCAL GMT
+ 9 : 00
POS SENS
24000 P/ NM
The following describes how to set the offset time between UTC (Universal
Time Coordinated) and the standard time of a time zone.
The offset time of the system defaults to "+9".
ON OFF
q Select "SETTING" on the Setting Menu screen using the [UP] or [DOWN] key
7.5 FT
+ 2.4 F
and press the [SET] key.
TEMP . F
The SETTING screen will appear.
123
w Select "OFFSET TIME" using the [UP] or [DOWN] key and press the [SET] key.
TRUE MAG
NOR REVS e Move to the time difference setting field using the [LEFT] or [RIGHT] key.
LOCAL GMT
The selected item is highlighted in yellow.
+09 : 00
r Enter the desired value into the time difference setting field using the [UP] or
POS SENS
24000 P/ NM
[DOWN] key and press the [SET] key.
SPEED 0 . 0KT
The setting is saved.
V1 . 5 V2 . 2
t When you finish setting the offset time, press the [MENU] key.
WP SHIP
You will return to the SET MODE screen.
SEL
SET
SET
This item allows you to make a selection between two ship speed signal sensing
options.
• POS:
LOCAL GMT
• SENS:
+ 9 : 00
POS SENS
24000 P/ NM
SPEED 0 . 0KT
V1 . 5 V2 . 2
The following describes how to correct the ship speed for difference between
the actual speed and the speed sensor reading.
q Select "SETTING" on the SET MODE screen using the [UP] or [DOWN] key and
ON OFF
press the [SET] key.
7.5 FT
The SETTING screen will appear.
+ 2.4 F
w Select "SPEED ADJ" using the [UP] or [DOWN] key and press the [SET] key.
TEMP . F
123
e Enter the pulse rate of the speed sensor into the pulse rate setting field using
TRUE MAG
[UP] or [DOWN] key and press the [SET] key.
NOR REVS
* When using an optional sensor, EX-1622 (transom type speed/temperature sen-
LOCAL GMT
+ 9 : 00
sor), set the pulse rate to "24000 P/NM".
POS SENS
When using an optional transducer, EX-1010 (through-the-hull type transducer
24000 P/ NM
with speed/water temperature sensor), set the pulse rate to "22000 P/NM".
SPEED 0 . 0KT
V1 . 5 V2 . 2 * If the above setting causes an error to occur, adjust the pulse rate while refer-
WP SHIP
ring to the speed reading displayed on the screen.
r When you finish correcting the ship speed, press the [MENU] key.
SET
SET
You will return to the SET MODE screen.
Normal indication
Reverse indication
Local standard time
Greenwich Mean Time (UTC)
Signals received by the GPS receiver are used to read the ship speed.
Signals detected by the sensor are used to read the ship speed.