Icom FP-561 Instruction Manual page 67

| TEMP ADJ
SETTING
AUTO GAIN ON
DRAFT ADJ 7.5 FT
+ 2.4 F
TEMP ADJ
TEMP
DATUM 000
TRUE
BEARING
COMPASS IND NOR
TIME REF LOCAL
+ 9: 00
OFFSET TIME
SPEED DATA POS
SPEED ADJ 24000 P/
SPEED
NMEA OUT V1 . 5
BOD OUT WP
ADJ
CANC
CLR SET
| DATUM
SETTING
AUTO GAIN ON
DRAFT ADJ 7.5 FT
+ 2.4 F
TEMP ADJ
TEMP
DATUM 123
TRUE
BEARING
COMPASS IND NOR
TIME REF LOCAL
+ 9 : 00
OFFSET TIME
SPEED DATA POS
SPEED ADJ 24000 P/
SPEED
NMEA OUT V1 . 5
BOD OUT WP
ADJ
CANC
CLR SET
| BEARING
SETTING
AUTO GAIN ON
DRAFT ADJ 7.5 FT
TEMP ADJ + 2.4 F
TEMP
DATUM 123
BEARING TRUE
COMPASS IND NOR
TIME REF LOCAL
OFFSET TIME – 8 : 30
SPEED DATA POS
SPEED ADJ 22000 P/
SPEED
NMEA OUT V1 . 5
BOD OUT WP
SEL
CANC
CLR SET
The following describes how to correct the water temperature detected by the
temperature sensor.
q Select "SETTING" on the Setting SET MODE using the [UP] or [DOWN] key and
OFF
press the [SET] key.
The SETTING screen will appear.
. F
w Select "TEMP ADJ" using the [UP] or [DOWN] key and press the [SET] key.
The current water temperature is indicated in the temperature setting field on the
MAG
SETTING screen.
REVS
GMT e Enter the desired value into the temperature setting field using the [UP] or
[DOWN] key and press the [SET] key.
SENS
The setting is saved.
NM
0 . 0KT * The permissible correction range is "–20 to +20".
V2 . 2
r When you finish correcting the water temperature, press the [MENU] key.
SHIP
You will return to the SET MODE screen.
SET
The build-in GSP receiver of the system receives signals from the GPS, and the
GPS uses the WGS-84 geodetic reference system, a global geodetic reference
system.
The following describes how to select the geodetic reference system of nautical
OFF
charts you currently use, in order to avoid positioning errors due to differences
between the nautical charts and the WGS-84. (see pgs. 77, 78; DATUM TABLE)
. F
q Select "SETTING" on the SET MODE screen using the [UP] or [DOWN] key and
MAG
press the [SET] key.
REVS
The SETTING screen will appear.
GMT
w Select "DATUM" using the [UP] or [DOWN] key and press the [SET] key.
SENS
e Move the geodetic system setting filed using the [LEFT] or [RIGHT] key.
NM
The selected digit in the field is highlighted in yellow.
0 . 0KT
r Enter the value corresponding to the nautical charts you currently use using the
V2 . 2
SHIP
[UP] or [DOWN] key and press the [SET] key.
SEL
The setting is saved.
SET
t When you finish setting geodetic data, press the [MENU] key.
You will return to the SET MODE screen.
The following describes how to correct the ship or destination bearing that
will be displayed on the coastline screen or other screens.
• TRUE; True bearing, MAG; Magnetic bearing
OFF
q Select "SETTING" on the SET MODE screen using the [UP] or [DOWN] key and
press the [SET] key.
. F
The SETTING screen will appear.
w Select "BEARING" using the [UP] or [DOWN] key and press the [SET] key.
MAG
e Select "True" or "Magnetic" using the [LEFT] or [RIGHT] key and press [SET]
REVS
GMT
key.
The setting is saved.
SENS
r When you finish setting the azimuth, press the [MENU] key.
NM
0 . 0KT
You will return to the SET MODE screen.
V2 . 2
SHIP
SET
INITIAL SETTING AFTER INSTALLATION
5
64