Enrolling/Deleting Of Devices; Enrolling Devices During The Initial Power-Up Of The Control Panel; Enrolling Devices To A Working System Configuration Via Lcd Keyboard - Teletek electronics ECLIPSE 8 Installation Manual

5. ENROLLING/DELETING OF DEVICES

5.1. Enrolling Devices during the Initial Power-up of the Control Panel

1. With set RESET jumper on the main PCB power-up the Eclipse control panel.
2. Wait the initial initialization of the connected to the system bus keyboards. At the end of the procedure, the
bus LED of all devices including the main PCB is lighting permanently in red. A text message "SW revision XX;
Press ENTER" is displayed on LCD screen, and at LED keyboards is lighting on only the power LED.
For LED 8/16A only the buttons 0-9 are lighting on.
3. Start to press the ENTER button or the address button of other devices – the manufacturer recommends first
to enroll the keyboards in the system, then proxy readers, modules, etc. The system starts an automatic
enrollment procedure of the devices on consecutive addresses as the first is attached at address 2 (in address
menus 8020). Remember that the first enrolled device to the system bus is always the main PCB of the panel.
It is strongly recommended the next enrolled device to be LCD keyboard for programming, especially for
system configurations with Eclipse 99 control panel.
4. Remove the RESET jumper and wait the system bus LED to stop blinking in green. The system is ready for
further programming and parameter configuration.
5. Set an actual time and date.

5.2. Enrolling Devices to a working system configuration via LCD keyboard

1. Enter engineer code (7777 by default).
2. Press button "9" for direct access to menu "9. DEVICES". Use the buttons with arrows to reach a free
address position for adding a new device. Choose in sequence:
3. Press the ENTER button (for a keyboard), press the button (for module) or place a card (in front of the proxy
readers) of the device connected to the system bus and which you want to enroll to the system configuration.
4. After successful enrollment to the control panel, the screen displays:
The following device types are supported from ECLIPSE Series control panels:
Device Description
MAIN The main PCB of the control panel
LED Keyboard LED8/16A/32
LCD Keyboard LCD 32/32S
ZEXP Zone expander
PEXP PGM expander
WEXP Wireless expander
PRX Proximity card reader
PIR Wireless motion detector
MC Wireless magnetic contact
FLD Wireless flood detector
FIRE Wireless fire detector
SIRN Wireless outdoor siren
REMT Remote key fob
* Eclipse 8: Up to 2 devices can be enrolled to the system bus: 2 keyboards, 2 proximity card readers or 1
keyboard and 1 proximity card reader.
** Eclipse 16: Up to 5 devices can be enrolled to the system bus irrespective of their type.
*** Eclipse 32/99: Up to 30 devices can be enrolled to the system bus irrespective of their type.
NOTE: It is not necessary to enroll the built-in proximity reader in keyboards LED 32 PR, LCD 32 PR and LCD
32S. The wireless devices can be enrolled only to wireless expander module Eclipse WL, which already has
been added to the system configuration.
5. Press ENTER button of the used for programming keyboard. The keyboard will confirm the end of the
successful enrollment procedure with sound signal.
ХХ. Device [Free] – ENTER – 1. ID – ENTER – [Free] [________]
[Device type] [unique ADDRESS] for the respective device.
ECLIPSE 8*
Eclipse 8/16/32/99 Series - Installation Manual
ECLIPSE 16**
✓ ✓
✓ ✓
✓ ✓
 ✓
 
 ✓
✓ ✓
 ✓
 ✓
 ✓
 ✓
 ✓
 ✓
33
ECLIPSE 32*** ECLIPSE 99***
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓