Intelligent interactive fire alarm control panel (25 pages)
Summary of Contents for Teletek electronics ECLIPSE 8
Page 1
USER OPERATION MANUAL ECLIPSE 8 ECLIPSE 16 ECLIPSE 32 ECLIPSE 99 (S.W. 3.xx) ALARM CONTROL PANELS Attention: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read.
ECLIPSE 8/16/32/99 Series – User Operation Manual Table of Contents: 1. GENERAL INFORMATION .................... 5 2. SUPPORTED KEYBOARDS ..................6 2.1 LED Keyboards ......................6 2.2 LCD Keyboards ......................6 2.3 Buttons Functionality ....................7 2.4 Indication ........................8 2.5 Sound Signalization ....................9 2.6 Directions for Operation with LED Keyboards ............
Page 3
ECLIPSE 8/16/32/99 Series – User Operation Manual 5.4 Turning on the Chime signalization by Manager ............ 28 5.5 Zones bypassing by Manager ................28 5.6 Engineer Access ....................28 5.7 Assigning User attributes ..................29 5.8 Associating Area numbers to User ................. 30 5.9 Entering of User names ..................
Page 4
The manufacturer shall not accept any product, of which no prior notice has been received via the RAN form at: https://teletek-electronics.com/en/ran-form. The setup and programming included in the technical documentation shall not be regarded as defects. Teletek Electronics bears no responsibility for the loss of programming information in the device being serviced.
The ECLIPSE family includes: ECLIPSE 8 for management of small sites up to 8 zones organized in 1 common area and for up to 8 users. ECLIPSE 16 for management of small to medium sites up to 16 zones organized in 3 independent areas and for up to 32 users.
ECLIPSE 8/16/32/99 Series – User Operation Manual 2. SUPPORTED KEYBOARDS According your system configuration, you may use one of the following keyboard models: Keyboard Display Areas Zones Card reader LED 8 LED 16A (option) LED 32 (option)
ECLIPSE 8/16/32/99 Series – User Operation Manual 2.3 Buttons Functionality Button Function Description Confirmation of the entered data. For LED 8 and LED 16A keyboards: Use the button to review the memory log file, the ENTER system troubles and the bypassed zones – the respective system LED is blinking during the review.
ECLIPSE 8/16/32/99 Series – User Operation Manual 2.4 Indication Button/LED Color Description The area is in FULL ARM mode. The area is in STAY ARM mode. The area is in SLEEP ARM mode. Permanently lit - there are bypassed zones in the system.
ECLIPSE 8/16/32/99 Series – User Operation Manual 2.5 Sound Signalization All ECLIPSE Series Keyboards have sound signalization for occurring of different system events. The sound signalization has 4 volume levels adjustable in menu “5. KBD SETTINGS - 1. BUSSER LEVEL” (Address 90) from the Manager programming menus.
ECLIPSE 8/16/32/99 Series – User Operation Manual 2.6.2 Special indication for reviewing of address number (LED 8 and LED 16A) With DISARM button the user can check the number of the current address during manager or user programming. You can use the button in the following way: 1.
ECLIPSE 8/16/32/99 Series – User Operation Manual • LED 8 and LED16A: After user code is entered a confirmation beep is heard from the keyboard. Entrance in programming mode by a user is done by pushing the PRG ( ) button. One digit is lit on...
ECLIPSE 8/16/32/99 Series – User Operation Manual 3. OPERATION INSTRUCTIONS 3.1 Arming with a Keyboard 3.1.1 Full Arming Mode Full Arm mode means that all zones in the armed areas are being protected. Full Arm can be initialized after entering a valid user code or with quick access without code, when this option is allowed in the menus for engineer programming.
ECLIPSE 8/16/32/99 Series – User Operation Manual 3.1.4 Arming All Available Areas in the System The user can perform arming of all available for operation areas in system. According the way of arming – with or without entering a user code – the number of the armed areas can be different.
ECLIPSE 8/16/32/99 Series – User Operation Manual • LCD Keyboards The status of the used areas is viewed with pressing of ENTER button. Note that the “padlock” LED lights up in red only when all the used areas are armed. The “padlock” LED lights up in green if at least one of the used areas is disarmed.
ECLIPSE 8/16/32/99 Series – User Operation Manual 3.1.7 Changing the Arming Mode without Disarming This is an extra functionality for changing the current arming mode with other without disarming before that. To use this feature, keep in mind that the following priority between...
ECLIPSE 8/16/32/99 Series – User Operation Manual 3.2.2 Arming via Stand-alone Proxy Reader PR IT and Eclipse PR The User can arm the system via stand-alone proxy reader in one of the following arming modes, which are programmed in advance from the system engineer: - “Full ARM”...
ECLIPSE 8/16/32/99 Series – User Operation Manual 3.3 Disarming Every user can disarm only those areas associated for operation to its personal code. Note: Certain users may not be permitted to disarm the system. 3.3.1 Disarming via keyboard The user can disarm one, several or all areas at the same time.
ECLIPSE 8/16/32/99 Series – User Operation Manual 3.4 Stopping the Sounders A triggered alarm can be stopped by entering a valid user code or a valid user card placed in front of the proxy reader. Note: The user code must have assigned rights to operate with area where the alarm event is triggered off the sirens.
Page 19
ECLIPSE 8/16/32/99 Series – User Operation Manual The indication for the technical troubles according the used keyboard is as follows: Control panel Eclipse LED 32/ LCD 32/ LED 8 Description LED 16A LCD 32 S The mains power supply is ...
ECLIPSE 8/16/32/99 Series – User Operation Manual 3.8 Checking the Bypassed Zones According the used keyboard, the indication for bypassed zones differs. Keyboard Indication and checking the bypassed zone The BYPASS LED is lit. In order to check the bypassed zones, you need to press the ENTER button once.
ECLIPSE 8/16/32/99 Series – User Operation Manual 4.1 Changing own code Every user without manager rights in the system can change only his/her own access code. To change the code, the user needs to enter the currently valid code: Main screen...
2, because these keyboards do not have a MEMORY fast button. 4.3 Turning on the Chime signalization by User Attention: This menu is available for ECLIPSE 8 control panel only. The Chime signalization is a sound signal from the keyboards when opening an entry/exit type zone.
ECLIPSE 8/16/32/99 Series – User Operation Manual 4.4 Zone bypassing by User Every user can bypass only zones that are associated to areas he is allowed to work with (arm and/or disarm). Bypassing zones is done in menu “4. ZONE BYPASS” (Address 4)
ECLIPSE 8/16/32/99 Series – User Operation Manual 4.5 Adding Own Proxy Card Every user without manager rights in the system can add or remove only his/her own proxy card for controlling the system. The adding and removing is done in a one and same menu “5.
ECLIPSE 8/16/32/99 Series – User Operation Manual 4.6 Deleting Own Proxy Card To delete his/her own card, the user needs to do in sequence: Text menu/ Press and hold address for 2-3 sec. User Code Depending on the keyboard used, the visualization on screen is as follows:...
Page 26
ECLIPSE 8/16/32/99 Series – User Operation Manual Quick table for Managers’ Programming Menu ECLIPSE Address Programming Text Menus Number parameter 1. Users Settings for user passwords and rights xx. User XX is the user number, according the panel 1-32 1-64 1-99 01.
ECLIPSE 8/16/32/99 Series – User Operation Manual 5.1 Creating and Changing User codes Creating new and changing existing user codes is realized in menu “1. USERS” (Address 01). When operating with text menus you must just follow the order from the quick table.
ECLIPSE 8/16/32/99 Series – User Operation Manual 5.4 Turning on the Chime signalization by Manager Attention: This menu is available for ECLIPSE 8 control panel only. The Chime signalization is a sound signal from the keyboards when opening an entry/exit type zone.
ECLIPSE 8/16/32/99 Series – User Operation Manual Depending on the keyboard used, the visualization on screen is as follows: LCD 32 and LCD 32 Sensitive (address menus) Engineer access is enabled Engineer access is disabled Press the digit buttons or arrow buttons to change alternatively the state of the parameter.
ECLIPSE 8/16/32/99 Series – User Operation Manual Depending on the keyboard used, the visualization on screen is as follows: LCD 32 and LCD 32 Sensitive In text menus the user will see the described above options as a list. To enable an option, press button “1”...
ECLIPSE 8/16/32/99 Series – User Operation Manual Depending on the keyboard used, the visualization on screen is as follows: LCD 32 and LCD 32 Sensitive (address menus, Eclipse 32) Areas 1, 2 and 3 are associated Associating area 4 By pressing the respective digit button, the area is alternatively enabled or disabled. The area is associated when the digit is visible on screen.
ECLIPSE 8/16/32/99 Series – User Operation Manual 5.10 Associating Timeslots to User Attention: This menu is available for ECLIPSE 32/99 control panel. From 1 to 8 timeslots for Eclipse 32 and from 1 to 16 timeslot numbers for Eclipse 99 with working hours can be defined in the system.
ECLIPSE 8/16/32/99 Series – User Operation Manual 5.11 Assigning Attributes for user proxy card In menu “1. USERS – xx. User – 06. Proxy Options” or Address 10, the manager sets rights to user cards for arming/disarming the system via proximity card reader.
ECLIPSE 8/16/32/99 Series – User Operation Manual LED 8/LED 16A Enter at the address 10 and choose a user number - the LED for zone 1 is blinking on the display. The digit buttons corresponding to the set proxy options are lighting on in red. To change settings, press the respective button number according the table above.
ECLIPSE 8/16/32/99 Series – User Operation Manual Depending on the keyboard used, the visualization on screen is as follows: LCD 32 and LCD 32 Sensitive Code numbers: Enter consecutively Source First Last code numbers The cloning process starts by entering the number of the code that will be cloned (“Source”).
ECLIPSE 8/16/32/99 Series – User Operation Manual The manager can set one of the following functions: Text menus Address option Description UNUSED No function of the button. This is the default set function. SLEEP ARM SLEEP ARM mode. STAY ARM STAY ARM mode.
ECLIPSE 8/16/32/99 Series – User Operation Manual Depending on the keyboard used, the visualization on screen is as follows: LCD 32 and LCD 32 Sensitive With the help of the digit buttons enter hour and minutes in the format [HH:ММ] –...
ECLIPSE 8/16/32/99 Series – User Operation Manual 5.19 Blocking Remote Access via UDL In menu “4. SETTINGS – 5. REMOTE ACCESS” or Address 16 the Manager can enter the number of allowed incorrect code (ARM / DISARM/BYPASS/PC ID) via UDL for a period of 24 hours.
ECLIPSE 8/16/32/99 Series – User Operation Manual In address menus the attributes are corresponding to the numbers from the table below: Address Manager code Assigning rights Remote access rights: Text menus Address attribute Description DISARM Allows remote disarm AREA ARM Allows remote arm.
ECLIPSE 8/16/32/99 Series – User Operation Manual 5.22 Setting the Sound Level In menu “5. KBD SETTINGS – 1. BUZZER LEVEL” or Address 90 you can set the volume level of the keyboard buzzer. The setting is individual for every keyboard and there are 4 different volume levels.
ECLIPSE 8/16/32/99 Series – User Operation Manual 5.24 Scroll speed of messages in LCD keyboards Attention: This address is available only in keyboards LCD32 and LCD32 Sensitive. In menu “5. KBD SETTINGS – 3. SCROLL SPEED” or Address 92, the scroll speed of system messages on the keyboard display is set.
Page 42
ECLIPSE 8/16/32/99 Series – User Operation Manual Activated zone with “24h Burglary” AUX attribute Restored zone with “24h Burglary” AUX attribute Activated zone with AUX “AC Loss” attribute Restored zone with AUX “AC Loss” attribute ...
Page 43
ECLIPSE 8/16/32/99 Series – User Operation Manual Manual test No AC mains power supply Mains power supply restore Battery low charge Battery loss Battery restore Siren output short-circuit Siren line broke out ...
ECLIPSE 8/16/32/99 Series – User Operation Manual APPENDIX B – Special Symbols for Text Entering Use the MEMORY button to enter some special symbols and Cyrillic letters. To enter a specialized symbol, move the cursor to the desired position, press the MEMORY button (a solid cursor appears) and then using the digit buttons enter the respective code for the symbol or letter as check in the table below.
Page 45
ECLIPSE 8/16/32/99 Series – User Operation Manual Table of special symbols and codes correspondence for GR keyboard version: Table of special symbols and codes correspondence for EU keyboard version: Note: The symbols for codes from 032 to 122 are same for all keyboard display versions.
If during 40 seconds time interval there is no action – pressed button, the system will break up the line. * Note: When operating with Eclipse 8 the messages for entering of Area number are missed and the user has not to enter an Area number.
ECLIPSE 8/16/32/99 Series – User Operation Manual System Check List – Fill in from the Installer System: Eclipse 8 / Eclipse 16 / Eclipse 32 / Eclipse 99 Installer: ....................... Service: ......................Tel./Fax: ....................... Zones Description Zone Type Zone Type...