BRP Lynx REV-XU Series Operator's Manual
  1. Manuals
  2. Brands
  3. BRP Manuals
  4. Snowmobiles
  5. Lynx REV-XU Series
  6. Operator's manual

BRP Lynx REV-XU Series Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2019
REV-XU
TM
Series
Read this guide thoroughly.
It contains important safety information.
Minimum recommended operator's age: 16 years old.
Keep this Operator's Guide in the vehicle.
6 1 9
9 0 0
9 6 9
Original Instructions

Advertisement

Table of Contents
loading

Related Manuals for BRP Lynx REV-XU Series

Summary of Contents for BRP Lynx REV-XU Series

  • Page 1 2019 REV-XU Series Read this guide thoroughly. It contains important safety information. Minimum recommended operator’s age: 16 years old. Keep this Operator’s Guide in the vehicle. 6 1 9 9 0 0 9 6 9 Original Instructions...
  • Page 2 ©...
  • Page 3 ® ROTAX ® Lynx ® D.E.S.S.™ TRA™ XU™ HPG™ PPS™ 619900969 en COJT ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates. ©2018 Bombardier Recreational Products Inc. and BRP US Inc. All rights reserved.

  • Page 4: Foreword

    Bombardier Recreational Products of your snowmobile as well as com- Inc. (BRP) warranty and a network of pleted the final adjustment required to authorized Lynx snowmobile dealers suit your specific weight and riding en-...

  • Page 5: Know Before You Go

    BRP reserves The safety alert symbol indicates a the right at any time to discontinue or potential injury hazard.
  • Page 6 FOREWORD This Operator's Guide should remain with the vehicle when it's sold. _______________...

  • Page 7: Table Of Contents

    Installation of Studs on BRP Approved Tracks ....... . 28...
  • Page 8 TABLE OF CONTENTS CONTROLS, INSTRUMENTS AND EQUIPMENT (cont’d) 8) Gearshift Lever ............. . . 49 9) Adjustable Mirrors.
  • Page 9 TABLE OF CONTENTS OPERATING MODES (900 ACE AND 1200 4-TEC)......78 ECO Mode (Fuel Economy Mode) .
  • Page 10 ® BRP FINLAND OY INTERNATIONAL LIMITED WARRANTY: 2019 LYNX SNOWMOBILES ..............160 MAINTENANCE RECORDS .
  • Page 11 TABLE OF CONTENTS _______________...

  • Page 12: Safety Information

    SAFETY INFORMATION ________ ________ SAFETY INFORMATION...

  • Page 13: General Precautions

    Do not make unauthorized modifica- tions, or use attachments or acces- To prevent serious injury or death from sories that are not approved by BRP. carbon monoxide: Since these changes have not been – Never run the vehicle in poorly ven-...

  • Page 14: Special Safety Messages

    – BRP recommends the operator has at least 16 years old of age. – It is very important to inform any operator, regardless of his experience, of the handling characteristics of this snowmobile.
  • Page 15 SPECIAL SAFETY MESSAGES – Speeding can be fatal. In many cases, you cannot react or respond quickly enough to the unexpected. Always ride at a speed which is suitable to the trail, weather conditions and your own ability. Know your local rules. Speed limit may be in effect and meant to be observed.
  • Page 16 – You may stud the track on this vehicle model. However, you MUST only use the BRP approved type stud for use on Lynx snowmobiles. DO NOT EVER use con- ventional studs, the track thickness is thinner compared to some other tracks.

  • Page 17: Active Technologies (Itc) (900 Ace And 1200 4-Tec)

    ACTIVE TECHNOLOGIES (iTC) (900 ACE AND 1200 4-TEC) Introduction Sport Mode NOTE: Some functions or features de- In sport mode, maximum engine scribed in this section may not apply to power is available throughout the en- every model, or may be available as an gine operational range.

  • Page 18: Riding The Vehicle

    RIDING THE VEHICLE Each operator has a responsibility to Before Starting the Engine ensure the safety of other recreation- 1. Remove snow and ice from body in- ists or bystanders. cluding lights, seat, footrests, con- You are responsible for proper opera- trols and instruments.
  • Page 19 RIDING THE VEHICLE 2. Check the engine cut-off switch (by 3. Release parking brake. pulling tether cord cap) and emer- WARM UP 4. Refer to the section and gency engine stop switch opera- follow instructions. tion. Pre-Ride Check List ✔ ITEM OPERATION Body including seat, footrests,...

  • Page 20: How To Ride

    RIDING THE VEHICLE How to Ride First aid kit Provided tool kit Mobile phone Knife Riding Gear Proper snowmobile clothing should Flashlight Spare spark plugs be worn. It should be comfortable Friction tape Trail map and not too tight. Always check the weather forecast before going on a Spare drive belt Snack...
  • Page 21 RIDING THE VEHICLE Sitting Feet on the running boards, body mid- way back on seat is an ideal position when operating the snowmobile over familiar, smooth terrain. Knees and hips should remain flexible to absorb shocks. fmo2008-003-003 Standing Place both feet on the running boards. Knees should be flexed to absorb the shock from surface bumps.

  • Page 22: Carrying A Passenger

    BRP recommends that the the vehicle. In addition, “body eng- child sits in the center location. This lish”...

  • Page 23: Terrain/Riding Variations

    RIDING THE VEHICLE Deep Snow WARNING In deep “powder” snow, your vehicle When riding with a passenger: could begin to “bog” down. If this oc- – Braking ability and steering curs, turn in as wide an arc as possible control are reduced. Decrease and look for a firmer base.
  • Page 24 RIDING THE VEHICLE yourself plenty of room for stopping If a higher than safe speed is reached, and turning. This is especially true at slow down by braking but apply the night. brake with frequent light pressure. Never jam the brake and lock the track. Hard Packed Snow Side Hill Don't underestimate hard packed...
  • Page 25 RIDING THE VEHICLE Here are some web sites that can help Unseen Obstruction you finding important information: There may be obstructions hidden – Europe: www.avalanches.org beneath the snow. Driving off es- tablished trails and in the woods re- Slush quires reduced speed and increased vigilance.
  • Page 26 RIDING THE VEHICLE surfaces, “body english” is the key to snowmobile is no match for a train. turning. Leaning towards the inside of Before crossing a railroad track, stop, the turn and positioning body weight look and listen. on the inside foot will create a “bank- ing”...

  • Page 27: Environment

    RIDING THE VEHICLE Signals ture of our sport. Help us lead it down the right path! From all of us at BRP, If you intend to stop, raise either hand thank you for doing your share. straight above your head. A left turn is...
  • Page 28 RIDING THE VEHICLE Light Treading in no way suggests you Respecting the areas where we ride... should curb your appetite for snowmo- wherever they may be... is the only biling fun! It simply means tread with way to ensure their future enjoyment. respect! That's one major reason why we know you'll agree that Light Treading is smart...

  • Page 29: Traction Enhancing Products

    BRP for special studs installation. adaptation period. If your snowmobile is equipped with traction enhancing products, be sure to take plenty of time...

  • Page 30: Acceleration

    TRACTION ENHANCING PRODUCTS Acceleration Using studs on the track will allow your sled to accelerate better on packed snow and ice but will have no notice- able effect on soft snow. This can cause sudden variations in traction under certain conditions. WARNING A33A31A To prevent surprises that could...

  • Page 31: Important Safety Rules

    The use of traction enhancing products To ensure safe and proper installation, can increase the load and the stress on BRP recommends to have the studs in- certain snowmobile components, as stalled by your dealer. well as the vibration level. This can –...

  • Page 32: Inspection Of A Studded Track

    TRACTION ENHANCING PRODUCTS – Lugs that are broken or torn off, ex- WARNING posing portions of rods – See an authorized Lynx dealer – Delamination of the rubber for current specific studding – Broken rods availability and applications. – Broken studs (studded tracks) –...

  • Page 33: Important On-Product Labels

    IMPORTANT ON-PRODUCT LABELS Hang Tag Vehicle Safety Labels Read and understand all the safety la- bels on your vehicle. These labels are affixed to the vehicle for the safety of Dear consumer, the operator, passenger or bystander. Your new E-TEC engine technology has an automatic computer- r - controlled break-in period that ensures you get the most The following labels are on your vehicle performance, efficiency and reliability for the life.
  • Page 34 IMPORTANT ON-PRODUCT LABELS Label 1 Label 2 WARNING – Locate and read operator's guide. Improper snowmobile use can result in SEVERE IN- JURY or DEATH. Follow all in- structions and warnings. – Always wear ear protection. – Never use with drugs or alcohol. 516009225 EN-516009225-DEC LABEL 2...
  • Page 35 IMPORTANT ON-PRODUCT LABELS Label 4 L L abel 6 WARNING Beware of rotating parts. 516006873 COMMANDER GT AND 69 RANGER SNOWCRUISER MODELS - LABEL 6 L L abel 7 516006900 en ON PULLEY GUARD - LABEL 7 Label 8 WARNING –...
  • Page 36 - Check oil level using the dipstick. - The engine of this snowmobile has been developed and validated using the BRP XPS Synthetic 4-stroke oil ( 293 600 112 ). BRP recommends the use of its XPS approved lubricant or equivalent.
  • Page 37 IMPORTANT ON-PRODUCT LABELS Label 12 Label 13 WARNING Beware of rotating track •Read and understand all safety labels, locate and read operator's guide and watch the safety video (using the QR code link or visit Ski-Doo web site) before operation. •Get familiar with your vehicle.

  • Page 38: Technical Information Labels

    IMPORTANT ON-PRODUCT LABELS Technical Information Labels Always electrically disconnect both fuel injectors prior to testing for ignition spark. Otherwise, fuel vapors may ignite in presence of a spark creating a fire hazard. 5583A 516005583A ON FUEL INJECTORS - E-TEC MODELS fmo2014-005-007_a fmo2014-003-008_a mmo2013-004-046_a...
  • Page 39 BRP recommends the use of its XPS approved lubricant or equivalent. Damages caused by oil which is not suitable for this engine may not be covered by the BRP limited warranty. See the operator’ s guide. 516007443 516007443 2-TEC- MODELS - ON ENGINE...
  • Page 40 IMPORTANT ON-PRODUCT LABELS 516004294 ON CONSOLE NEAR SHIFT LEVER 516005672 ON CONSOLE - ALL COMMANDER AND 69 RANGER 900 ACE- MODELS DEC 513033943 EN-FR LOCATED ON FUEL CAP ________ ________ SAFETY INFORMATION...
  • Page 41 IMPORTANT ON-PRODUCT LABELS This page is intentionally blank _______ ________ SAFETY INFORMATION...

  • Page 42: Vehicle Information

    VEHICLE INFORMATION _______________...

  • Page 43: Controls, Instruments And Equipment

    CONTROLS, INSTRUMENTS AND EQUIPMENT NOTE: Some features may not apply to your model or could be optional. NOTE: Some vehicle safety labels are not shown on illustrations. For information VEHICLE SAFETY LABELS on vehicle safety labels, refer to fmo2014-003-033_a TYPICAL - ALL MODELS EXCEPT 69 RANGER ALPINE ______________...
  • Page 44 CONTROLS, INSTRUMENTS AND EQUIPMENT fmo2013-006-001_d TYPICAL - 69 RANGER ALPINE MODELS ONLY fmo2013-003-002_a TYPICAL - ALL MODELS EXCEPT 69 RANGER ALPINE _______________...
  • Page 45 CONTROLS, INSTRUMENTS AND EQUIPMENT fmo2016-006-002_c TYPICAL - 69 RANGER ALPINE MODELS ONLY fmo2016-002-003_b COMMANDER GRAND TOURER 1200 4-TEC, 900 AND COMMANDER LIMITED 600 E-TEC fmo2012-003-016_b COMMANDER LIMITED 600 E-TEC AND 69 RANGER ARMY LTD fmo2014-003-004_a COMMANDER GRAND TOURER 1200 4-TEC AND 900 ECS²...

  • Page 46: Handlebar

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2015-008-002_38 mmo2008-008-011_b TYPICAL - LH SIDE OF FUEL TANK - 900 ACE TYPICAL AND 1200 4-TEC 1. Throttle lever 2. To accelerate 1) Handlebar 3. To decelerate The handlebar controls the steering WARNING of the snowmobile. As the handlebar Test the throttle lever operation is rotated to right or left, the skis are each time before starting the en-...

  • Page 47: Brake Lever

    CONTROLS, INSTRUMENTS AND EQUIPMENT WARNING Test the throttle lever operation each time before starting the en- gine. The lever must return to its the rest position once released. Otherwise, do not start engine. Switching from Thumb to Finger Throttle Position mmo2015-008-100_a CAUTION It is highly recom- IF WANTED, CONTINUE TO ROTATE THE...

  • Page 48: Parking Brake Lever

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2014-004-001_a mmo2009-005-006_a TYPICAL 1. Brake lever TYPICAL — ENGAGE MECHANISM 2. To apply brake Step 1: Apply and hold regular brake Step 2: Lock brake lever using parking brake lever 4) Parking Brake Lever Parking brake lever is located on the LH To Release Parking Brake side of handlebar.

  • Page 49: Emergency Engine Stop Switch

    CONTROLS, INSTRUMENTS AND EQUIPMENT RF D.E.S.S. (Digitally Encoded The Lynx learning key, limits the speed Security System) of the snowmobile and the engine torque, therefore enabling first time The tether cord cap has an integrated users and less experienced operators D.E.S.S.

  • Page 50: Multifunction Switch

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2016-008-201_a ON POSITION fmo2014-003-003_a All operators of the snowmobile 1. Start button should familiarize themselves with the 2. Headlights dimmer switch function of the emergency engine stop 3. Heated grips switch by using it several times on first 4.
  • Page 51 CONTROLS, INSTRUMENTS AND EQUIPMENT Heated Grips Switch Heated Throttle Lever Switch fmo2014-003-003_c fmo2014-003-003_b TYPICAL TYPICAL 1. Heated throttle lever switch 1. Heated grips switch 2. Increase heat (Warmer) 2. Increase heat 3. Decrease heat (Colder) 3. Decrease heat NOTE: The heating intensity is dis- The heating intensity is displayed via played via the multifunction display the multifunction display.

  • Page 52: Gearshift Lever

    CONTROLS, INSTRUMENTS AND EQUIPMENT Mode/Set Button WARNING This button can be used instead of the Adjust with vehicle at rest in a safe two buttons on top of the analog/digital place. gauge to facilitate gauge adjustments. – When pressed left, it has the same 10) Tool Kit functions as the MODE (M) button.

  • Page 53: Front And Rear Bumpers

    CONTROLS, INSTRUMENTS AND EQUIPMENT Models with an Under Seat Storage Box fmo2012-003-007_a TYPICAL 1. Rear bumper fmo2015-003-001_a NOTICE Do not use skis or ski han- TYPICAL dles to pull or lift snowmobile. 1. Tool kit 12) Gauge 11) Front and Rear Bumpers WARNING To be used whenever snowmobile re-...
  • Page 54 CONTROLS, INSTRUMENTS AND EQUIPMENT WARNING Never adjust or set functions on the multifunction gauge while rid- ing the vehicle, you could lose con- trol. The multifunction display is used to: – Display the WELCOME message on power up – Display the KEY recognition mes- sage mmo2008-007-017 –...
  • Page 55 CONTROLS, INSTRUMENTS AND EQUIPMENT MONITORING SYS- See table below for usual pilot lamps information. Refer to for details on malfunction pilot lamps. PILOT LAMP(S) BEEPER MESSAGE DISPLAY DESCRIPTION 4 short Two stroke engine: Injection oil level is low. Stop vehicle beeps in a safe place then, replenish injection oil reservoir.
  • Page 56 CONTROLS, INSTRUMENTS AND EQUIPMENT Gauge Features AVAILABLE INDICATIONS IN NUMERICAL DISPLAY 800R 1200 FUNCTIONS 600 E-TEC 900 ACE E-TEC 4-TEC A) Speedometer B) Engine RPM C) Odometer D) Trip meter “A” or “B” E) Trip hour meter F) Clock G) Fuel level H) Altitude N.A.
  • Page 57 CONTROLS, INSTRUMENTS AND EQUIPMENT A) Speedometer Press the MODE (M) button to confirm selection or wait 5 seconds. addition analog type speedometer, vehicle speed can also be displayed via the multifunction display. Vehicle speed can be displayed on dis- play 1 or display 2. mmo2007-009-066_o B) Tachometer (RPM) In addition of the analog type tachome-...
  • Page 58 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_n mmo2007-009-066_p 1. RPM mode 1. Trip meter (TRIP A/TRIP B) mode Press the MODE (M) button to confirm Press and hold the SET (S) button to re- selection or wait 5 seconds. set. NOTE: Resetting TRIP B mode will also reset TOTAL FUEL CONSUMP- TION.
  • Page 59 CONTROLS, INSTRUMENTS AND EQUIPMENT H) Altitude Displays vehicle approximate altitude above sea level calculated from the barometric pressure. NOTE: Altitude displayed is rounded off every 100 meters (gauge set in metric) or 200 feet (gauge set in impe- rial units). mmo2007-009-066_k To display vehicle altitude, proceed as follows.
  • Page 60 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_o I) Heated Grips Heating Intensity mmo2007-009-044_a HEATED THROTTLE LEVER Bar gauge that indicates heating inten- 1. Operating range sity. K) Instant Fuel Consumption NOTE: There are nine intensity set- tings. When released, display will re- Calculates vehicle average fuel con- turn to engine coolant temperature (if sumption while riding.
  • Page 61 CONTROLS, INSTRUMENTS AND EQUIPMENT Press the MODE (M) button to confirm TC appears when the mode is se- selection or wait 5 seconds. lected. mmo2008-003-021_a TYPICAL mmo2007-009-066_o Press the MODE (M) button to confirm L) Total Fuel Consumption selection or wait 5 seconds. Records vehicle average fuel con- sumption since it has been reset.
  • Page 62 CONTROLS, INSTRUMENTS AND EQUIPMENT P) Top Speed Records vehicle top speed since it has been reset. To display vehicle top speed, proceed as follow. Push the MODE (M) button to select display. mmo2007-009-066_w M) Message Display mmo2007-009-066_m NOTE: Display will flash for approxi- mately 5 seconds, then will return to mmo2007-009-066_c the previously selected mode if display...
  • Page 63 CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_o mmo2007-009-066_m To reset, push the MODE (M) to select NOTE: Display will flash for approxi- mode. mately 5 seconds, then will return to the previously selected mode if display is not changed. Push SET (S) button to select vehicle average speed (AVR_SPD) mode.

  • Page 64: Backrest (If Equipped)

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2007-009-066_m mmo2007-009-066_k Push and hold the SET (S) button within To change HOURS, while the value of 5 seconds to reset. HOURS is blinking, use the SET (S) but- ton to change hours. To change MINUTES, while the value of HOURS is blinking, press the MODE (M) button to switch to minutes.

  • Page 65: Passengers Handholds (If Equipped)

    CONTROLS, INSTRUMENTS AND EQUIPMENT Passenger Seat Removal CAUTION When closing lid with the passenger seat installed, To remove the passenger seat, pro- ceed as follows: secure with the retaining strap. NOTE: A distinctive snap will be felt. 1. Push the latch tab in and lift-up the Double check that the seat is secure by rear of seat.

  • Page 66: Mountain Strap (If Equipped)

    CONTROLS, INSTRUMENTS AND EQUIPMENT mmo2009-004-021 fmo2012-003-020_a TYPICAL 1. Passenger handhold To set the handholds to the desired po- sition, proceed as follows: 16) Mountain Strap (If 1. Pull up the knob and unscrew sev- Equipped) eral turns until the handhold is free to move.

  • Page 67: Rear Rack

    CONTROLS, INSTRUMENTS AND EQUIPMENT Battery WARNING Battery is located in storage box under The storage compartment must passenger seat. To access the battery, be properly latched and must not remove the cover by pushing both tabs contain any sharp or breakable ob- in, then lifting it up.

  • Page 68: 12-Volt Power Outlet

    CONTROLS, INSTRUMENTS AND EQUIPMENT When attaching any accessory, always refer to the manufacturer's recom- mendations. NOTE: Refer to decal on vehicle for towing weight capacities. WARNING Never tow an accessory with a rope. Always use a rigid tow bar. Using a rope would result in a col- lision between the object and the mmo2009-005-010_a snowmobile and possibly in a tip...

  • Page 69: Adjustable Handlebar (If Equipped)

    1. Anchor points ding availability and applications. Two anchor points are provided to se- BRP does not recommend to ride a cure load in rear rack. snowmobile equipped with high lug profile track at high speed in a trail, on...

  • Page 70: Drive Belt Guard

    CONTROLS, INSTRUMENTS AND EQUIPMENT 26) Drive Belt Guard Place belt guard front openings over tabs. Drive Belt Guard Removal WARNING NEVER operate engine: – Without shields and belt guard securely installed. – With hood and/or side panels opened or removed. NEVER attempt to make adjust- ments to moving parts while en- gine is running.

  • Page 71: Hood

    CONTROLS, INSTRUMENTS AND EQUIPMENT 27) Hood 3. Hook the rubber ties. WARNING 28) Upper Side Panels Never operate engine with hood WARNING removed from vehicle. Never operate engine with side Hood Removal panels opened or removed from vehicle. 1. Remove upper side panels as ex- plained below.

  • Page 72: Lower Side Panels

    CONTROLS, INSTRUMENTS AND EQUIPMENT 2. Hook the panel top center tabs to the console. mmo2009-004-044_a 1. Rubber tie mmo2011-006-100_a 1. Console hook 3. Turn the clip 1/4 turn counterclock- 2. Console slot 3. Panel center tabs wise to unlock. 3. Insert the rear tab into the console slot.

  • Page 73: Rewind Starter Handle (If Equipped)

    CONTROLS, INSTRUMENTS AND EQUIPMENT 30) Rewind Starter Handle 2. Insert the lower section of side panel over the aluminium chassis (If Equipped) and the aluminium tab into the panel Auto-rewind type located on right hand slot. side of snowmobile behind side panel. To engage mechanism, pull handle slowly until a resistance is felt then pull vigorously.

  • Page 74: Storage Box (If Equipped)

    CONTROLS, INSTRUMENTS AND EQUIPMENT NOTE: Do not sit or lean on seat when To install storage box, make sure that fuel tank cap is not properly installed. the tunnel surface is clean. Put stor- age box within the rear rack rails. 33) Storage Box (If Attach using...

  • Page 75: Seat Heater (If Equipped)

    CONTROLS, INSTRUMENTS AND EQUIPMENT fmo2016-002-003_c 1. ECS², module mmo2015-008-002_a TYPICAL - LH SIDE OF FUEL TANK REAR SUSPENSION ADJUST- Refer to 1. Mode switch MENT TUNE YOUR RIDE in the sec- tion It is used to activate or deactivate Eco/Standard/Sport modes. 37) Seat heater (If OPERATING MODES Refer to...

  • Page 76: Lighting Rack (If Equipped)

    CONTROLS, INSTRUMENTS AND EQUIPMENT fmo2013-006-010_a fmo2013-006-012_a 1. Drive horn 1. Brake light indicator 2. Working light 3. Beacon 44) Widening Kit (If 42) Lighting Rack (If Equipped) Equipped) Widening kit increases stability when The lighting rack kit includes beacon turning on steep slopes. and working light.

  • Page 77: Fuel And Oil

    FUEL AND OIL Fuel Requirements MINIMUM FUEL ENGINE OCTANE TYPE NOTICE Always use fresh gaso- RATING line. Gasoline will oxidize; the re- Fuel 600 HO sult is loss of octane, volatile com- which E-TEC pounds, and the production of gum 800 R and varnish deposits which can contain...

  • Page 78: Recommended Oil

    NOTICE The engine of this snow- Recommended Oil mobile has been developed and val- idated using the BRP XPS™ oil. BRP 600 HO E-TEC and 800R E-TEC recommends the use of its XPS oil or equivalent. Damages caused by oil...
  • Page 79 FUEL AND OIL Always maintain a sufficient amount of recommended injection oil in the injec- tion oil reservoir. fmo2012-003-012_a TYPICAL 1. Injection oil reservoir 2. Level marks (1/4, 1/2, 3/4) NOTICE Check level and refill ev- ery time you refuel. To Add Injection Oil Remove injection oil reservoir cap.

  • Page 80: Break-In Period

    BREAK-IN PERIOD Operation During Break-In – Avoid pulling a load. – Avoid high speed cruising. A break-in period of 10 operating hours or 500 km (300 mi) is required for the vehicle. After the break-in period, the vehicle should be inspected by an authorized Lynx dealer, repair shop, or person of FIRST IN- your own choosing.

  • Page 81: Operating Modes (900 Ace And 1200 4-Tec)

    OPERATING MODES (900 ACE AND 1200 4-TEC) To increase power, press the switch WARNING upwards. To decrease power, press Whenever changing operating the switch downwards. mode, make sure to maintain situ- ational awareness while riding. ECO Mode (Fuel Economy Mode) When ECO mode is selected (fuel economy mode), vehicle torque and speed are limited whereby an optimal...

  • Page 82: Learning Key Modes (Optional)

    OPERATING MODES (900 ACE AND 1200 4-TEC) Learning Key Modes (Optional) The learning key provides a mode of operation whereby engine torque and speed are limited. NOTE: The initial learning key pro- gramming limit speed 40 km/h (25 MPH) 70 km/h (43 MPH).

  • Page 83: Operating Instructions

    OPERATING INSTRUCTIONS Engine Starting Procedure E-TEC Models If the starter does not operate and you Procedure ENGINE have followed the steps in STARTING PROCEDURE 1. Apply parking brake. , start engine with the emergency cord as follows: 2. Recheck throttle lever operation. 3.

  • Page 84: Vehicle Warm-Up

    OPERATING INSTRUCTIONS mmo2008-005-007 3. Attach the other end of emergency mmo2008-005-014_a rope to the starter clip supplied in 6. Pull the rope using a sharp, crisp pull the tool kit. so the rope comes free of the drive pulley. WARNING When starting the snowmobile in an emergency situation, using drive pulley, do not reinstall the...

  • Page 85: Gearbox Operation

    OPERATING INSTRUCTIONS NOTICE If vehicle does not move Neutral when throttle is applied, stop en- When set in neutral (N), the gearbox gine, remove tether cord cap from disengages the pulleys from the track. the engine cut-off switch, then do the following.

  • Page 86: Shifter Rod Adjustment

    OPERATING INSTRUCTIONS Shifter Rod Adjustment Towing an Accessory 1. Adjust shifter rod to initial length Always use a rigid tow bar to tow an ac- from end to end 258mm cessory. Any towed accessory should have reflectors on both sides and at the 2.

  • Page 87: Tune Your Ride

    TUNE YOUR RIDE Following are guidelines to fine-tune WARNING suspension. Suspension adjustment could af- fect vehicle handling. Always take time to familiarize yourself with the vehicle's behavior after any suspension adjustment have been made. Snowmobile handling and comfort de- pend upon suspension adjustments. Choice of suspension adjustments vary with carrying load, driver's weight, personal preference, riding speed and...
  • Page 88 TUNE YOUR RIDE REAR AND FRONT SUSPENSION SPRING PRELOAD FACTORY SETTINGS REAR ARM MODEL FRONT ARM 7 mm / cam 15 mm / cam 30 mm / cam Commander 600 E-TEC position #2 position #4 position #4 7 mm / cam 15 mm / cam 30 mm / cam Commander Limited 600...

  • Page 89: Rear Suspension Adjustment

    TUNE YOUR RIDE Rear Suspension Adjustment NOTICE Whenever adjusting rear suspension, check track tension and adjust as necessary. 619900696-001 EASYRIDE REAR SUSPENSION 1. Easy Adjust Handle 2. Rear spring 3. Center spring 4. Stopper strap Stopper Strap Ride at low speed then fully accelerate. fmo2015-003-003_a Note steering behavior.
  • Page 90 TUNE YOUR RIDE ACTION RESULT Firmer rear suspension Higher rear end Increasing More bump absorption preload capability Heavier steering Softer rear suspension Lower rear end Less bump absorption Decreasing fmo2015-006-002_a capability preload TYPICAL 1. Adjustment holes (stopper strap) Lighter steering NOTE: Decreasing the stopper strap Better performance and length may reduce comfort.
  • Page 91 TUNE YOUR RIDE NOTE: If the specification is unattain- able with the original springs, see an authorized Lynx dealer for other avail- able springs. NOTICE increase spring preload, always turn the left side adjustment cam in a clockwise di- rection, and the right side cam in a counterclockwise direction.
  • Page 92 TUNE YOUR RIDE ADJUSTMENT CHART Hauling heavy Comfort Comfort Carrying cargo loads (1-up) (2-up) Soft Setting Hard Setting Electronic Controlled Suspension To increase or decrease the damping ( ECS²) (If Equipped) push the left knob till the MAN/shock figure led lights up. Push the right knob ECS²...
  • Page 93 TUNE YOUR RIDE WARNING Before proceeding with any sus- pension adjustment, remember: – park in a safe place – remove tether cord cap – lift rear of vehicle off the ground with a wide-base snowmobile stand with a rear deflector panel –...

  • Page 94: Front Suspension Adjustment

    TUNE YOUR RIDE When operating the snowmobile in deep snow, it may be necessary to set Center arm to position 2. mmo2009-004-031_a TYPICAL - FRONT SUSPENSION 1. Front springs for handling WARNING fmo2013-005-003_a CENTER ARM Always adjust both front springs to 1.

  • Page 95: Vehicle Behavior Related To Suspension Adjustment

    TUNE YOUR RIDE mmo2010-003-027_a CAM TYPE - HPG SHOCK ABSORBER 1. Decrease preload 2. Increase preload 3. Spring preload adjustment cam Vehicle Behavior Related to Suspension Adjustment PROBLEM CORRECTIVE MEASURES Check ski alignment and camber angle adjustment. See an authorized Lynx dealer. Reduce ski ground pressure.

  • Page 96: Vehicle Transportation

    VEHICLE TRANSPORTATION Make sure that oil reservoir and fuel tank caps are properly installed. Tilt bed trailers can easily be equipped with a winch mechanism to afford maximum safety in loading. Simple as it may seem, never drive your snow- mobile onto a tilt bed trailer or any other kind of trailer or vehicle.
  • Page 97 VEHICLE TRANSPORTATION This page is intentionally blank ______________...
  • Page 98 MAINTENANCE _______________...

  • Page 99: First Inspection

    FIRST INSPECTION After the first 10 hours or 500 km (300 mi) of operation, whichever comes first, your vehicle have to be inspected by an authorized Lynx dealer, repair shop, or person of your own choosing. The break-in inspection is very important and must not be neglected.
  • Page 100 FIRST INSPECTION FIRST INSPECTION (4-STROKE) AFTER THE FIRST 500 KM (300 MI) OR 10 HOURS OF OPERATION, WHICHEVER COMES FIRST Inspect engine seals and gaskets for leaks Inspect exhaust system and check for leaks ENGINE Check coolant level FUEL Inspect fuel lines and connections SYSTEM Inspect drive belt Visually inspect drive pulley...

  • Page 101: Maintenance Schedule (2-Stroke)

    MAINTENANCE SCHEDULE (2-STROKE) NOTE: The maintenance schedule does not exempt the pre-ride inspection. WARNING Failure to properly maintain the vehicle according to the maintenance schedule and procedures can make it unsafe to operate. EVERY 1 500 KM (1,000 MI) Models with chaincase: Adjust drive chain DRIVE Models with chaincase: Check chaincase oil level SYSTEM...
  • Page 102 MAINTENANCE SCHEDULE (2-STROKE) EVERY 6 000 KM (4,000 MI) OR 2 YEARS (WHICHEVER COMES FIRST) ENGINE Clean and lubricate rewind starter Inspect fuel pump strainer and replace if necessary FUEL SYSTEM Inspect throttle cable Replace brake fluid Lubricate the splines of joint between QRS axle and gearbox (XU models) DRIVE Lubricate the splines of joint between driven pulley and QRS axle (XU...

  • Page 103: Maintenance Schedule (4-Stroke)

    MAINTENANCE SCHEDULE (4-STROKE) NOTE: The maintenance schedule does not exempt the pre-ride inspection. WARNING Failure to properly maintain the vehicle according to the maintenance schedule and procedures can make it unsafe to operate. EVERY 1 500 KM (1,000 MI) Models with chaincase: Adjust drive chain DRIVE Models with chaincase: Check chaincase oil level SYSTEM...
  • Page 104 MAINTENANCE SCHEDULE (4-STROKE) EVERY 6 000 KM (4,000 MI) OR 2 YEARS (WHICHEVER COMES FIRST) Replace fuel filter FUEL SYSTEM Replace fuel pump outlet filter (ACE) Replace drive pulley slider shoes, O-ring and rollers and inspect ramps (1200 4-TEC and 900 ACE) DRIVE Replace brake fluid SYSTEM AND...

  • Page 105: Maintenance Procedures

    MAINTENANCE PROCEDURES Engine Coolant This section includes instructions for basic maintenance procedures. WARNING WARNING Never open coolant tank cap when Turn off the engine, remove tether engine is hot. cord cap and follow these mainte- nance procedures when perform- Engine Coolant level ing maintenance.

  • Page 106: Injection Oil (600 Ho E-Tec, 800R E-Tec)

    MAINTENANCE PROCEDURES Recommended Engine Coolant Always maintain a sufficient amount of recommended injection oil in the injec- RECOMMENDED ENGINE COOLANT tion oil reservoir. EXTENDED LIFE PRE-MIXED Scandinavia COOLANT (EUR) (P/N 779223) EXTENDED LIFE PRE-MIXED All other COOLANT countries (P/N 779150) Distilled water and Alternative, or if antifreeze solution...

  • Page 107: Engine Oil Replacement (900 Ace)

    MAINTENANCE PROCEDURES NOTICE 2. Let engine run at idle for 30 more Engine oil and oil filter seconds. must be replaced at the same time. 3. Stop engine. 1. Bring engine to its normal operating 4. Open the LH side panel, refer to temperature.

  • Page 108: Engine Oil Replacement (1200 4-Tec)

    MAINTENANCE PROCEDURES mmr2011-070-004_a fmo2016-003-012_b 1. Sealing washer 2. Oil drain plug PIVOT THE ACCESS COVER 1. Retaining screws 12. Install drain plugs and tighten to 7. Clean drain plug area. specification. 8. Place a drain pan under the bottom TIGHTENING TORQUE pan opening.
  • Page 109 MAINTENANCE PROCEDURES NOTICE Engine oil and oil filter 10. Allow oil to drain completely. must be replaced at the same time. 11. Install NEW sealing washer and O-ring on oil drain plug. 1. Bring engine to its normal operating temperature. NOTICE Never sealing...

  • Page 110: Engine Oil Filter (900 Ace)

    MAINTENANCE PROCEDURES Engine Oil Filter (900 ACE) Engine Oil Filter Replacement Oil Filter Removal 1. Remove the RH side panel. 2. Clean oil filter area. 3. Remove: – Oil filter cover screws – Oil filter cover with O-ring mmr2011-070-008_a – Oil filter. 1.

  • Page 111: Exhaust System

    MAINTENANCE PROCEDURES 3. Clean oil filter area. 3. Lubricate filter seal and cover O-ring with engine oil. 4. Remove: – Oil filter cover screws – Oil filter cover with O-ring – Oil filter. mmr2009-111-008_a 1. Lubricate with engine oil 4. Install the oil filter cover. 5.

  • Page 112: Spark Plugs

    MAINTENANCE PROCEDURES Spark Plugs Spark plugs inspection or replacement may be performed by an authorized Lynx dealer, repair shop, or person of your own choosing. Spark plugs in- spection or replacement requires an in-depth technical knowledge. Though not required, it is recommended that an authorized Lynx dealer performs spark plugs inspection or replacement.

  • Page 113: Brake Fluid

    MAINTENANCE PROCEDURES WARNING Use only DOT 4 brake fluid from a sealed container. To avoid serious damage to the braking system, do not use fluids other than the rec- ommended one, nor mix different fluids for topping up. mmo2010-009-007_b TIGHTENING SEQUENCE TIGHTENING TORQUE Stopper 10 N•m ±...

  • Page 114: Gearbox Oil Replacement

    BRP strongly recommends the use of its XPS oil at all times. Dam- ages caused by oil which is not suit- able for the gearbox will not be cov- ered by the BRP limited warranty. mmo2009-004-034_a Gearbox Oil Level TYPICAL With the vehicle on a level surface, 1.

  • Page 115: Drive Belt

    MAINTENANCE PROCEDURES 5. Wait a while to allow all oil to drain 4. Reinstall check plug and tighten to out of gearbox. specification. 6. Install drain plug and tighten to spec- TIGHTENING TORQUE ification. Oil level check 10 N•m (89 lbf•in) TIGHTENING TORQUE plug Gearbox drain plug...
  • Page 116 MAINTENANCE PROCEDURES 5. If a new belt was installed, an adjust- ment will be required for the proper DRIVE BELT belt height. Refer to HEIGHT ADJUSTMENT below. DRIVE 6. Install belt guard, refer to BELT GUARD INSTALLATION SIDE 7. Close side panel, refer to PANELS CONTROLS, INSTRU- MENTS AND EQUIPMENT...
  • Page 117 MAINTENANCE PROCEDURES All Drive Belt Types NOTE: Turning the ring counterclock- wise lowers the belt in the pulley. Turn- ing the ring clockwise raises the belt in the pulley. 6. Tighten the clamping bolt to specifi- cation. TIGHTENING TORQUE mmo2011-003-011_a 5.5 N•m ±...

  • Page 118: Drive Pulley

    MAINTENANCE PROCEDURES Drive Pulley Drive Pulley Adjustment (only TRA) The drive pulley is factory calibrated for sea level operation. WARNING Remove the tether cord cap from engine cut-off switch before per- forming any adjustment. Vehicle A33D19A must be parked in a safe place, TYPICAL away from the trail.

  • Page 119: Track

    Traction Enhancing Products See your Lynx dealer to maintain If your snowmobile is equipped with or service the drive pulley. Im- a BRP approved studded track, PRO- proper servicing or maintenance CEED WITH A VISUAL INSPECTION may affect performance and re- OF YOUR TRACK BEFORE EACH duce belt life.
  • Page 120 MAINTENANCE PROCEDURES On approved studded tracks, replace 2. Lift rear of vehicle and support it off broken or damaged studs immediately. the ground. If your track shows signs of deteriora- tion, it must be replaced immediately. CAUTION Use proper lifting When in doubt, ask your dealer.
  • Page 121 MAINTENANCE PROCEDURES 9. Read load recorded by the upper O-ring on the tensiometer. mmr2009-133-003_a LOAD READING mmr2009-133-001_a 1. Upper O-ring mmr2009-133-002_a 1. Deflection O-ring aligned with slider shoe 10. Load reading must be as per the following table. TRACK ADJUSTMENT SPECIFICATION MODELS WITH 40 mm to 45 mm EASYRIDE...
  • Page 122 MAINTENANCE PROCEDURES 619900696-002 fmr2008-048-007_a EASYRIDE SUSPENSION ALL OTHERS 1. Adjustment screws 1. RH rear idler wheel cap NOTE: It may be necessary to rotate 3. Loosen the rear idler wheels retain- the drive belt to access the adjustment ing screws. screw.
  • Page 123 MAINTENANCE PROCEDURES If off center, perform alignment as fol- TIGHTENING TORQUE lows: 48 N•m ± 6 N•m Retaining bolts (35 lbf•ft ± 4 lbf•ft) WARNING Remove the tether cord cap from 7. Check track alignment as described engine cut-off switch before per- below.

  • Page 124: Suspension

    MAINTENANCE PROCEDURES Rear Suspension Lubrication Lubricate rear suspension at grease MAINTENANCE fittings. Refer to SCHEDULE maintenance fre- quency. SUSPENSION GREASE SYNTHETIC SUSPENSION recommended A05F0EB GREASE product (P/N 779163) TYPICAL 1. Locknut 2. Retaining bolts E E asyRide Suspension 6. Start engine and rotate track slowly to recheck alignment.

  • Page 125: Skis

    MAINTENANCE PROCEDURES All others fbl2013-002-014_c TYPICAL 1. Ski leg 2. Ski 3. Ski Runner Ski stance can be adjusted by spacer fmo2015-003-008_a location. It can be installed inside or 1. Grease fittings outside of the ski leg Steering and Front Suspension Condition Visually inspect steering and front sus- pension for tightness of components...

  • Page 126: Lights

    MAINTENANCE PROCEDURES To close upholstery, push the strip back WARNING in the aluminium extrusion. Do not use a higher rated fuse. Lights WARNING Always check light operation after bulb replacement. If fuse has burnt out, source of mal- function should be determined Headlights Bulb Replacement and corrected before restarting.
  • Page 127 MAINTENANCE PROCEDURES mmo2007-009-022_a 1. Rubber boots mmo2007-009-023_a TYPICAL 4. Press and pull both sides of the re- 1. Knobs taining clip at the same time to re- Taillight lease it from bulb support. The taillight is comprised of a LED as- sembly which is proven to be reliable and durable.

  • Page 128: Vehicle Care

    To remove grease, oil and grime, use BRP HEAVY DUTY CLEANER (P/N 293 110 001). NOTICE Do not use heavy duty cleaner on decals or vinyl. To remove stubborn dirt from all plastic and vinyl surfaces, use CLEANER AND DEGREASER PRO C1 (P/N 779262).

  • Page 129: Storage

    STORAGE During summer, or when a snowmobile is not in use for more than three months, proper storage is necessary. STORAGE Clean the vehicle VEHICLE ENGINE STORAGE MODE E-TEC models: Lubricate engine. See (E-TEC) below for instructions. Block muffler with rags ENGINE Protect fuel system by adding fuel stabilizer to fuel following the product manufacturer recommendations.
  • Page 130 STORAGE NOTE: The storage mode does not The engine lubrication function takes function in other modes (trip A, trip B approximately 1 minute. During this and hr trip). time engine RPM will increase slightly to approximately 1600 RPM and the oil 4.

  • Page 131: Preseason Preparation

    PRESEASON PREPARATION PRESEASON PREPARATION (2-STROKE) Inspect engine rubber mounts Check exhaust system condition and check for leaks Tighten exhaust manifold screws or nuts to specified torque ENGINE Inspect cooling system cap, hoses and clamps and check for leaks Check coolant density Inspect crankshaft PTO seal Inspect fuel lines and connections FUEL...
  • Page 132 PRESEASON PREPARATION PRESEASON PREPARATION (4-STROKE) Visually inspect engine seals and gaskets and check for leaks Check exhaust system condition and check for leaks ENGINE Change engine oil and filter Check coolant density Inspect fuel lines and connections FUEL SYSTEM Clean and inspect throttle body Inspect drive belt (adjust at every drive belt replacement) Clean and visually inspect drive pulley Clean and inspect driven pulley...
  • Page 133 PRESEASON PREPARATION This page is intentionally blank ______________...

  • Page 134: Technical Information

    TECHNICAL INFORMATION ______________...

  • Page 135: Vehicle Identification

    These numbers are required by the authorized Lynx dealer to complete warranty claims properly. No warranty will be allowed by BRP if the engine identification number or vehicle iden- tification number (VIN) is removed or mutilated in any way. We strongly rec-...
  • Page 136 VEHICLE IDENTIFICATION mmo2007-002-006_a 800R E-TEC ENGINE 1. Engine identification number mmo2009-005-039_a 1200 4-TEC ENGINE 1. Engine serial number mmo2014-004-007_a 900 ACE ENGINE 1. Engine identification number ______________...

  • Page 137: Noise Emission And Vibration Values

    NOISE EMISSION AND VIBRATION VALUES MODEL 600 HO E-TEC 800R E-TEC 1200 4-TEC 900 ACE NOISE EMISSION AND VIBRATION VALUES 96,7 dB @ 99,3 dB @ 98,1 dB @ 92,7 dB @ Sound power 4050 RPM 3950 RPM 3900 RPM 3625 RPM level (L (Uncertainty...

  • Page 138: Ec-Declaration Of Conformity

    The EC-Declaration of Conformity does not appear in this version of the Operator's Guide. Please refer to the printed version that was delivered with your vehicle. ddd2009-001...

  • Page 139: Radio Frequency Digitally Encoded Security System

    RADIO FREQUENCY DIGITALLY ENCODED SECURITY SYSTEM (RF D.E.S.S. KEY) This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

  • Page 140: Specifications

    SPECIFICATIONS SYSTEM MODELS ENGINE 600 HO E-TEC Engine type Rotax ® 593, liquid cooled w/Reed valve, 3D-RAVE Cylinders Displacement 594.4 cm³ (36.27 in³) Bore 72 mm (2.83 in) Stroke 73 mm (2.87 in) Maximum horsepower engine RPM 8100 RPM Fuel injection system E-TEC direct injection Exhaust system Single tuned pipe, baffle muffler...
  • Page 141 SPECIFICATIONS ENGINE 800R E-TEC Engine type Rotax ® 797, liquid cooled w/Reed valve, 3D-RAVE Cylinders Displacement 799.5 cm³ (48.79 in³) Bore 82 mm (3.23 in) Stroke 75.7 mm (2.98 in) Maximum horsepower engine RPM 7900 RPM Fuel injection system E-TEC direct injection Exhaust system Single tuned pipe, baffle muffler 2T E-TEC SYNTHETIC...
  • Page 142 SPECIFICATIONS ENGINE 900 ACE Engine type Rotax 903, liquid cooled, 4-stroke, D.O.H.C., dry sump Cylinders Displacement 899 cm³ (54.9 in³) Bore 74 mm (2.9 in) Stroke 69.7 mm (2.74 in) Maximum horsepower RPM 7250 RPM Exhaust system Single front pipe, baffle muffler 4T 0W40 SYNTHETIC Scandinavia: OIL (EUR) (P/N 779286)
  • Page 143 SPECIFICATIONS ENGINE 1200 4-TEC Rotax 1203, liquid cooled, 4-Stroke, D.O.H.C. Engine type with balancer shaft, dry sump Cylinders Displacement 1 170.7 cm³ (71.44 in³) Bore 91 mm (3.58 in) Stroke 60 mm (2.36 in) Maximum horsepower engine RPM 7800 RPM Fuel injection system Multi point EFI, 52 mm heated throttle body Exhaust system...
  • Page 144 SPECIFICATIONS DRIVE SYSTEM 600 HO E-TEC TRA III™ Type 800R E-TEC TRA VII™ 1200 4-TEC eDrive II Drive pulley 900 ACE 600 HO E-TEC 3000 RPM ± 100 800R E-TEC 3800 RPM ± 100 Engagement 1200 4-TEC 2200 RPM ± 100 900 ACE Driven pulley type QRS-SS...
  • Page 145 SPECIFICATIONS DRIVE SYSTEM (cont'd) Commander 600 HO E-TEC Commander LTD 600 HO E-TEC Commander LTD 900 ACE 44 mm Commander 800R E-TEC Commander 900 ACE 69 Ranger Army LTD Commander 600 HO E-TEC ICE ripper Commander 900 Track profile height ACE ICE ripper Commander GT 900 ACE Comfort...
  • Page 146 SPECIFICATIONS SUSPENSION (cont'd) 69 Ranger 900 ACE HPG 25 Front arm shock Commander 800R E-TEC KYB 36 All others HPG 36 Commander 600 HO E-TEC Commander 600 HO E-TEC ICE ripper Commander LTD 600 HO E-TEC Commander 900 ACE Commander LTD 900 ACE HPG 36 Commander 900 ACE ICE ripper...
  • Page 147 SPECIFICATIONS ELECTRICAL SYSTEM 600 HO E-TEC Lightning system output 12V/1340 W Headlights bulb HI/LOW beam 2 x 60/55 Watts (H-4) Taillight bulb Type NGK PZFR6F Spark plug 0.75 mm ± 0.05 mm (.03 in ± .002 in) (Not adjustable) F 1: Battery 30 A F 2: Start F 3: Front power outlet...
  • Page 148 SPECIFICATIONS ELECTRICAL SYSTEM 800 R E-TEC Lightning system output 12V/1340W Headlights bulb HI/LOW beam 2 x 60/55 Watts (H-4) Taillight bulb Type NGK PFR7AB Spark plug 0.75 mm ± 0.05 mm (.03 in ± .002 in) (Not adjustable) F 1: Battery 30 A F 2: Start F 3: Front power outlet...
  • Page 149 SPECIFICATIONS ELECTRICAL SYSTEM 900 ACE Lightning system output 12V / 650 W Headlights bulb HI/LOW beam 2 x 60/55 Watts (H-4) Taillight bulb 2.6 W / 139m W LED Type MR7B1 Spark Plug 0.8 mm (.031 in) F1 : Battery 30 A F2 : Relay / Start button F3 : Starter solenoid...
  • Page 150 SPECIFICATIONS ELECTRICAL SYSTEM 1200 4-TEC Lightning system output 12V/490 W Headlights bulb HI/LOW beam 2 x 60/55 Watts (H-4) Taillight bulb Type NGK CR8EKB Spark plug Not adjustable F 1: Battery 30 A F 2: Relay/start button F 3: Starter solenoid 10 A F 4: Cooling Fan 15 A...
  • Page 151 SPECIFICATIONS WEIGHT AND DIMENSIONS Commander 600 HO E-TEC 276 kg (608 lb) Commander 600 HO E-TEC 278 kg (613 lb) ICE ripper Commander LTD 600 HO 290 kg (639 lb) E-TEC Commander 800R E-TEC 282 kg (622 lb) Commander 900 ACE 285 kg (628 lb) Commander 900 ACE ICE 287 kg (633 lb)
  • Page 152 SPECIFICATIONS WEIGHT AND DIMENSIONS (cont'd) All models except 69 Ranger Alpine 1200 4-TEC Commander 800R E-TEC 144.5 cm (56.9 in) 69 Ranger SnowCruiser 900 ACE and 69 Ranger 900 ACE Vehicle overall height 69 Ranger Alpine 1200 4-TEC 140 cm (55.1 in) Commander 800R E-TEC 133 cm (52.4 in) 69 Ranger 900 ACE...
  • Page 153 SPECIFICATIONS This page is intentionally blank ______________...

  • Page 154: Troubleshooting

    TROUBLESHOOTING ______________...

  • Page 155: Troubleshooting Guidelines

    TROUBLESHOOTING GUIDELINES ELECTRIC STARTER DOES NOT WORK 1. Emergency engine stop switch in OFF position or tether cord cap not installed on engine cut-off switch. – Place the emergency engine stop switch in the ON position and install tether cord cap (on engine cut-off switch. 2.
  • Page 156 TROUBLESHOOTING GUIDELINES ENGINE LACKS ACCELERATION OR POWER (cont’d) 4. Engine break-in period not completed (E-TEC). – Complete break-in period. 5. Incorrect drive pulley adjustment. – Adjust drive pulley, refer to MAINTENANCE PROCEDURES. 6. Drive and driven pulleys require servicing. – Contact an authorized Lynx dealer. 7.
  • Page 157 TROUBLESHOOTING GUIDELINES HEATED GRIPS/THUMB WARMERS ARE NOT WORKING 1. Engine RPM is too low. – Make sure engine RPM is above 2000. ENGINE HAS SHUT DOWN 1. The engine shuts down after long periods of idling. – Do not let engine idle too long. Refer to VEHICLE WARM-UP in OPERATING INSTRUCTION.

  • Page 158: Monitoring System

    MONITORING SYSTEM Pilot Lamps, Messages and Beeper Codes Gauge pilot lamp(s) will inform you if an anomaly occurs or to inform you of a particular condition. mmo2013-004-045_b TYPICAL — PILOT LAMPS Pilot lamp can flash alone or in combi- nation with another lamp. On the multifunction analog/digital gauge, the display is used as a comple- ment of the pilot lamps to give you a...
  • Page 159 MONITORING SYSTEM NOTE: Some of the listed pilot lamps and messages do not apply to all models. PILOT MESSAGE LAMP(S) BEEPER DESCRIPTION DISPLAY 4 short Low engine oil pressure. Stop vehicle beeps in a safe place then, check oil level. Fill every LOW OIL to proper level.
  • Page 160 MONITORING SYSTEM PILOT MESSAGE LAMP(S) BEEPER DESCRIPTION DISPLAY 4 short beeps Engine RPM limited for protection when — every REV LIMIT certain faults occur. minutes On E-TEC engines, indicates that maximum — — OVER REV engine RPM is reached. Check clutch calibration.

  • Page 161: How To Read Fault Codes

    MONITORING SYSTEM How to Read Fault Codes Multifunction Analog/Digital Display Only To read any active fault code, press and hold MODE (M) Button and simul- taneously depress the HI/LOW beam switch repeatedly several times. If two or more codes are registered, use SET (S) or MODE (M) to scroll.

  • Page 162: Warranty

    WARRANTY ______________...

  • Page 163: Brp Finland Oy International Limited Warranty: 2019 Lynx

    BRP. BRP reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
  • Page 164 – Damage resulting from removal of parts, improper repairs, service, main- tenance, modifications or use of parts or accessories not manufactured or approved by BRP which in its reasonable judgement are either incompatible with the product or adversely affect its operation, performance and durability, or resulting from repairs done by a person that is not an authorized servicing LYNX Distributor/Dealer;...
  • Page 165 BRP will not honour this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 166 BRP reserves the right to improve or modify products from time to time without as- suming any obligation to modify products previously manufactured. 8) TRANSFER If the ownership of a product is transferred during the warranty coverage period, this limited warranty, subject to its terms and conditions, shall also be transferred...
  • Page 167 ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be responsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.

  • Page 168: Maintenance Records

    MAINTENANCE RECORDS Send photocopy of maintenance record to BRP if needed. PREDELIVERY Serial number: Signature/Print: Mileage / km: Hours: Date: Dealer no: Notes: Refer to vehicle Pre-Delivery Bulletin for detailed installation procedures FIRST INSPECTION Serial number: Signature/Print: Mileage / km:...
  • Page 169 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print:...
  • Page 170 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print:...
  • Page 171 This page is intentionally blank ______________...

  • Page 172: Customer Information

    CUSTOMER INFORMATION ______________...

  • Page 173: Contact Us

    CONTACT US South America www.brp.com Rua James Clerck Maxwell, 230 North America TechnoPark Campinas SP 13069-380 Brazil 565 de la Montagne Street Valcourt (Québec) J0E 2L0 Asia Canada Sturtevant, Wisconsin, U.S.A. 15/F Parale Mitsui Building,8 10101 Science Drive Higashida-Cho, Kawasaki-ku...

  • Page 174: Change Of Address/Ownership

    Notifying BRP, even after the expiration of the limited warranty, is very important as it enables BRP to reach the snowmobile owner if necessary, like when safety re- calls are initiated. It is the owner’s responsibility to notify BRP.
  • Page 175 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 176 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 177 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 178 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 179 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 180 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 181 GUIDE DU CONDUCTEUR, Série REV-XU / ANGLAIS FAIT AU / MADE IN CANADA U/M:P.C. ®™ AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES. ©2018 BOMBARDIER RECREATIONAL PRODUCTS INC. ALL RIGHTS RESERVED. PRINTED IN FINLAND.

This manual is also suitable for:

Lynx commander 600 e-tecLynx commander limited 600 e-tecLynx commander 800r e-tecLynx commander 900 aceLynx commander gt 900 aceLynx commander gt 1200 4-tec comfort ... Show all

Table of Contents