Page 2
Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
Turning the light source on or off......... 31 Cinema 4K-RGB Installation and Setup Guide–CP4315-RGB, CP4320-RGB, CP4325-RGB, CP4330-RGB 020-102710-08 Rev.
Safety precautions Learn about the safety precautions related to the Christie Cinema 4K-RGB projector. This projector is intended for use in a cinema environment. General safety precautions Read all safety and warning guidelines before installing or operating the projector. Warning! If not avoided, the following could result in death or serious injury.
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • SHOCK HAZARD! Disconnect the product from AC before installing, moving, servicing, cleaning, removing components, or opening any enclosure.
Page 7
• F—Represents the side view of the projector. The following table lists the hazard distance for the Christie projector lens with the zoom adjusted to its most hazardous position. For US market only, hazard distances based upon FDA guidance document 1400056, Classification and Requirements for Laser Illuminated Projectors (LIPs), dated February 18, 2015.
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.
Only trained Christie qualified technicians who are knowledgeable about the hazards associated with high-voltage, laser safety, and the high temperatures generated by the projector are authorized to assemble and install the projector. Only Christie qualified technicians are authorized to service the projector.
Do not install or operate the projector in an inverted position. If your site has any installation requirements other than a typical theater projection booth, contact Christie for assistance. Before lifting and positioning the projector, refer to the light intensity hazard distances.
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • A certified electrician must be present during installation to ensure the installation meets the local electrical code.
Linear Time Code (LTC) output. Output for multi-projector playback. Input for multi-projector playback (Christie IMB to Christie IMB only). SM and FIPS LED status indicators Indicates marriage status. In full power mode, a green LED indicates that the projector is properly married and encrypted content can be displayed.
Solid FIPS (Federal Information Processing Standards Publication) security status is operating correctly. Solid An error has occurred. Restart the Christie IMB. If the LED remains red, return the Christie IMB to Christie Digital Systems USA Inc. LED status indicators Identify the LED state colors and meaning.
For Red, Green, and Blue power levels, system stability may be affected if levels are set below the minimum (MIN) power limit shown. To ensure color and brightness are held at the required levels for your installation, Christie ™...
System stability may be affected if you set a power level below the minimum power level recommended. When setting the Red or Green power level, Christie recommends setting a level below the maximum (MAX) limit shown. A value below the maximum limit ensures an optimal brightness that can be maintained over time.
Do not install or operate the projector in an inverted position. If your site has any installation requirements other than a typical theater projection booth, contact Christie for assistance. The front-to-back tilt of the projector must not exceed 15° in a downward direction or 5° in an upward direction.
Extreme misalignment of projection optics can cause permanent damage to critical optical components. Only Christie qualified technicians can perform internal optical adjustments. The integrator rod and fold mirror adjustments are set by Christie. Make adjustments only if screen shadows are visible.
For the best stability, Christie recommends setting convergence while rotating the knobs in a clockwise direction. This may require first adjusting convergence by turning the knobs counter- clockwise, and finalizing the convergence with a clockwise approach.
Page 51
Corporate offi ces Worldwide offi ces Christie Digital Systems USA, Inc. Africa Columbia Mexico United States (Arizona) ph: 714 236 8610 ph: +27 (0)11 510 0094 ph: +57 (318) 447 3179 ph: +52 55 4744 1790 ph: 602 943 5700...