Daikin Madoka BRC1H519W7 Installer And User Reference Manual page 69

Indoor unit field settings
Mode SW
10 (20) 00 Filter contamination timer: set the timer for the
appearance of the "Time to clean filter" sreen.
01 Long life filter: if applicable, set which type of long life filter is used.
02 Controller thermostat sensor: set how the controller thermostat sensor is
used.
03 Disable filter sign: set whether or not the filter sign can be displayed.
11 (21) 00 Simultaneous operation: set the simultaneous indoor unit operation mode
(Sky Air)
12 (22) 01 External On/OFF input: set the operation of voltage free contacts T1/T2
(indoor unit contacts)
02 Thermostat differential: if the system contains a remote sensor, set the
increase/decrease increments.
13 (23) 00 High air outlet velocity: set in case of high-ceiling applications.
01 Airflow direction: set in case an indoor unit is equipped with an option kit that
blocks the airflow.
03 Airflow function: set whether the indoor unit is equipped with a decoration
panel at its air outlet.
04 Airflow direction range
06 External static pressure: set the external static pressure (according to the
resistance of the connected ducts).
FHYK: follow the high-ceiling setting.
15 (25) 03 Humidification drain pump
1c 01 Thermostat sensor: set which thermostat sensor you want to use.
1c 12 Window contact B1 (external input)
1c 13 Key card contact B2 (external input)
1e 02 Setback function: set Setback operation.
1e 07 Rotation overlap time. Set the Rotation overlap time.
1B 08 Daylight saving time. Set how the system controls daylight saving time.
(a)
This is applicable for codes 02-06. Codes 05 and 06 are not shown in the table. See the service manual for more detailed
information.
BRC1H519W+K+S7
Madoka wired remote controller
4P513689-1E – 2020.12
The setting procedure is different depending on whether you want to make
settings for individual indoor units, or for groups of indoor units.
Individual indoor units
▪ Define a mode by setting a Mode number (number between brackets)
▪ Define the unit to which the setting will apply by setting a Unit number
▪ Define the setting by setting a SW number
▪ Define a value for that setting
Groups of indoor units
▪ Define a mode by setting a Mode number (number NOT between brackets)
▪ Do NOT set a Unit number (setting applies to all the units in the group)
▪ Define the setting by setting a SW number
▪ Define a value for that setting
Setting (SW) description
Ultra long life filter
Long life filter
Standard filter
01
Light ±10000 hrs. Heavy
±2500 hrs
±200 hrs
Long life filter
Used in combination with indoor unit
thermistor
Display
Pair
Forced OFF
1°C
h≤2.7 m
4-way flow
Equipped
Upper
Normal
Normal
Not equipped Heating operation: continuous
Indoor unit thermistor
Do not use
Do not use
No Setback
30 minutes
Disable
14 Configuration
|
—
02 03
±5000 hrs —
±1250 hrs
±100 hrs
Ultra long life filter —
Not used Used
exclusively
Do not display —
Twin Triple
On/OFF operation Emergency
0.5°C —
2.7 m<h≤3 m 3 m<h≤3.5 m
3-way flow 2-way flow
Not equipped
Normal Lower
High static pressure Low static
pressure
High ceiling —
Heating operation: 3 minutes
ON/5 minutes OFF
Controller thermistor —
Use
Use
Heating only Cooling only
15 minutes 10 minutes
Automatic changeover Manual
changeover
Installer and user reference guide
04
—
—
—
—
Double twin
Forced OFF
(multi-tenant)
—
—
—
—
—
(a)
—
Heating and
Cooling
5 minutes
Centralised
control
69