Mitsubishi Electric AnyWire ASLINK User Manual page 125

Error code Classification
(hexadecimal)
1060H Minor error
1061H Minor error
1062H Minor error
1063H Minor error
1801H Minor error
1802H Minor error
1803H Minor error
1804H Minor error
1805H Minor error
1806H Minor error
1807H Minor error
1808H Minor error
1809H Minor error
180AH Minor error
Error name Error description and cause
Non-volatile An error could not be saved because
memory access an error was detected when accessing
error (error history) the non-volatile memory.
Non-volatile The IP address could not be saved
memory access because an error was detected when
error (IP address) accessing the non-volatile memory.
Non-volatile Module parameters could not be saved
memory access because an error was detected when
error (module accessing the non-volatile memory.
parameter)
Non-volatile The slave module ID and parameter
memory data error information saved in the non-volatile
(slave module ID, memory are faulty.
parameter)
Bit data points The value being set is outside the
setting range error settable range for the bit data points
setting.
Word data use The value being set is outside the
setting range error settable range for the word data usage
setting.
Word data points The value being set is outside the
setting range error settable range for the word data points
setting.
Word data start The value being set is outside the
address setting settable range for the word data start
range error address setting.
Number of word The value being set is outside the
data points per settable range for the number of word
frame setting range data points setting per frame.
error
Startup operation The value being set is outside the
mode setting range settable range for the startup operation
error mode setting.
Bit data double The value being set is outside the
verification setting settable range for the bit data double
range error check mode setting.
Disconnection error The value being set is outside the
automatic recovery settable range for the disconnection
mode setting range error automatic recovery mode setting.
error
Word input data The value being set is outside the
hold/clear setting settable range for the word input data
when disconnection hold/clear setting when disconnection
occurs range error occurs.
Output data hold/ The value being set is outside the
clear setting range settable range for the output data hold/
error clear setting.
Action
• Errors that occurred before this error may not have
been saved in the non-volatile memory.
• Take measures to reduce noise.
• If the error occurs again, the module may be in
failure. Please consult your local Mitsubishi
representative.
• The IP address is not saved in the non-volatile
memory.
• Take measures to reduce noise.
• If the error occurs again, the module may be in
failure. Please consult your local Mitsubishi
representative.
• Module parameters are not saved in the non-
volatile memory.
• Take measures to reduce noise.
• If the error occurs again, the module may be in
failure. Please consult your local Mitsubishi
representative.
• The slave module ID and parameter information
saved in the non-volatile memory are faulty.
Execute automatic address detection again. DP/
DN disconnection detection and parameter access
cannot be performed until automatic address
detection is executed.
• If the error occurs again, the module may be in
failure. Please consult your local Mitsubishi
representative.
Change Bit data points setting (address: 0100H) to a
setting value within the settable range, and turn on
Module parameter reflection request flag (RYC).
Change Word data use setting (address: 0101H) to a
setting value within the settable range, and turn on
Module parameter reflection request flag (RYC).
Change Word data points setting (address: 0102H)
to a setting value within the settable range, and turn
on Module parameter reflection request flag (RYC).
Change Word data start address setting (address:
0103H) to a setting value within the settable range,
and turn on Module parameter reflection request flag
(RYC).
Change Word data points setting per frame
(address: 0105H) to a setting value within the
settable range, and turn on Module parameter
reflection request flag (RYC).
Change Startup operating mode setting (address:
0107H) to a setting value within the settable range,
and turn on Module parameter reflection request flag
(RYC).
Change Double verification setting (address: 0108H)
to a setting value within the settable range, and turn
on Module parameter reflection request flag (RYC).
Change Disconnection error automatic recovery
mode setting (address: 0109H) to a setting value
within the settable range, and turn on Module
parameter reflection request flag (RYC).
Change Word input data hold/clear setting when
disconnected (address: 010AH) to a setting value
within the settable range, and turn on Module
parameter reflection request flag (RYC).
Change Output data hold/clear setting (address:
010BH) to a setting value within the settable range,
and turn on Module parameter reflection request flag
(RYC).
10 TROUBLESHOOTING
10.6 List of Error Codes
10
123