Surround Panning - Yamaha 006IPTO-F0 Owner's Manual

ST REVERB
Two input, two output stereo reverb.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
Hall, Room, Stage,
REV TYPE Reverb type
Plate
INI. DLY 0.0–100.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
LO. RATIO 0.1–2.4 Low-frequency reverb time ratio
Reverb diffusion (left–right
DIFF. 0–10
reverb spread)
DENSITY 0–100% Reverb density
Balance of early reflections and
E/R BAL. 0–100% reverb (0% = all reverb, 100% =
all early reflections)
THRU,
HPF High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
REVERB 5.1
One input, six output reverb for 5.1 surround, with

surround panning.

Parameter Range
REV TIME 0.3–99.0 s Reverb time
Hall, Room,
REV TYPE Reverb type
Stage, Plate
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
Reverb diffusion (left–right reverb
DIFF. 0–10
spread)
DENSITY 0–100% Reverb density
THRU,
HPF High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0
LPF Low-pass filter cutoff frequency
kHz, THRU
Divergence determines how the
front center signal is fed to the
Left, Right, and Center channels.
When set to 0%, it's fed only to
the Left and Right channels (i.e.,
DIV. 0–100%
Phantom Center). When set to
50%, it's fed equally to the Left,
Right, and Center channels. When
set to 100%, it's fed to only the
Center channel (i.e., Real Center).
ROOMSIZE 0.1–20.0 Size of simulated room's reverb
POS L/R L63–R63 Left/right listening position
POS F/R F63–R63 Front/rear listening position
1
POS CTRL OFF, NOR, INV
ER L/R L63–R63 Left/right early reflections position
Front/rear early reflections posi-
ER F/R F63–R63
tion
ER LVL 0–100% Early reflections level
ER CTRL OFF, NOR, INV 1
REV L/R L63–R63 Left/right reverb position
REV F/R F63–R63 Front/rear reverb position
REV LVL 0–100% Reverb level
REV CTRL OFF, NOR, INV 1
Radius of the panning track at the
POS RAD. 0–63
listening position
Radius of the panning track for
ER RAD. 0–63
early reflections
Radius of the panning track for
REV RAD. 0–63
reverb
1. When set to NOR, the position can be set by using the Joystick so
long as the SELECTED CHANNEL PAN/SURROUND [EFFECT]
button's indicator is on. When set to INV, the Joystick will work
inversely. When set to OFF, Joystick control is off.
OCTA REVERB
Eight input, eight output reverb.
Description Parameter
REV TIME
REV TYPE
INI. DLY
HI. RATIO
LO. RATIO
DIFF.
DENSITY
E/R BAL.
HPF
LPF
AUTO PAN 5.1
Six input, six output autopanner for 5.1 surround.
Parameter
Description
SOURCE
TRG LVL
TRG MASK 0–1000 ms
TIME
SPEED
DIR.
OFFSET
HPF
LPF
• When you press the RESET button, the phase will be initialized to
the setting of the OFFSET parameter.
Effects Parameters
Range Description
0.3–99.0 s Reverb time
Hall, Room, Stage,
Reverb type
Plate
0.0–100.0 ms Initial delay before reverb begins
0.1–1.0 High-frequency reverb time ratio
0.1–2.4 Low-frequency reverb time ratio
Reverb diffusion (left–right
0–10
reverb spread)
0–100% Reverb density
Balance of early reflections and
0–100% reverb (0% = all reverb, 100% =
all early reflections)
THRU,
High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
Range Description
Source specifies the trigger that
will initiate auto pan. When you
press the TRIGGER button in the
screen, auto pan will begin
regardless of the setting of this
OFF, HOLD, parameter.
INPUT1, INPUT2, OFF: No trigger is specified. Auto
INPUT3, INPUT4, pan will always be off.
INPUT5, INPUT6, HOLD: No trigger is specified.
MIDI Auto pan will always be on.
INPUT 1-6: The input signal to
effect inputs 1-6 will be the trig-
ger.
MIDI: MIDI note-on messages
will be the trigger.
If SOURCE is set to INPUT, any
signal with a level greater than
–60 to 0 dB
the setting of this parameter will
be detected as a trigger.
Trigger Mask specifies the time
from when a trigger is received
until the next trigger will be
accepted.
The time after which autopan
0.1 s–10.0 s
starts once it's been triggered
0.05–40.00 Hz Autopan speed
Turn L, Turn R Autopan direction
–180 to +180
Pan offset
degrees
THRU,
High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
DM1000 Version 2—Owner's Manual
319