Side panel for the dm1000 digital production console (2 pages)
Summary of Contents for Yamaha DM1000
Page 1
LSI PIN DESCRIPTION ........ 47 IC BLOCK DIAGRAM ........58 CIRCUIT BOARDS ........65 INSPECTIONS ........... 103/109 DM1000/MB1000 SERVICE CHECK PROGRAM ....115/129 MB1000 TEST PROGRAM ........143/144 INITIALIZING THE DM1000 ....145 TRANSMITTING PARAMETER SETTINGS VIA MIDI (BULK DUMP) ..146/148 CHECKING THE BATTERY AND THE SYSTEM VERSION ..
Page 2
IMPOR TANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under- stood by the users, and have therefore not been restated.
Page 3
DM1000/MB1000/SP1000 LITHIUM BATTERY HANDLING This product uses a lithium battery for memory back-up. WARNING : Lithium batteries are dangerous because they can be exploded by improper handling. Observe the following pre- cautions when handling or replacing lithium batteries. Leave lithium battery replacement to qualified service personnel.
DM1000/MB1000/SP1000 SPECIFICATIONS General Spec Number of scene memories 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz Internal Sampling Frequency Normal rate: 44.1 kHz–10% to 48 kHz+6% External Double rate: 88.2 kHz–10% to 96 kHz+6% Less than 1.6 ms CH INPUT to OMNI OUT...
Page 5
DM1000/MB1000/SP1000 — Input patch Phase Normal/reverse On/off Gate-type * Key in: 12 ch Group (1–12, 13–24, 25–36, 37–48)/AUX1–8 On/off Comp-type * Key in: self /Stereo Link Pre EQ/pre fader/post fader –96.0 to +12.0 dB (0.1 dB step) Attenuator 4-band PEQ (TYPE1) * On/off 0–43400 samples...
Page 6
DM1000/MB1000/SP1000 On/off Comp-type * Pre EQ/pre fader/post fader Attenuator –96.0 to +12.0 dB (0.1 dB step) 4-band PEQ * On/off On/off — STEREO Fader 100 mm motorized Balance 127 positions (Left=1–63, Center, Right=1–63) Delay 0–29100 samples Displayed on LCD Peak hold on/off...
Page 7
DM1000/MB1000/SP1000 100 V, 50/60 Hz 135 W Japan Power Requirements 120 V, 60 Hz 135 W U.S./Canada Other 220–240 V, 50/60 Hz 135 W 200 x 585 x 436 mm (7.8" x 23.0" x 17.1") With MB1000 and SP1000 installed: 295 x 635 x 486 mm (11.6" x 25.0" x...
Page 8
DM1000/MB1000/SP1000 Comp Parameters –54 dB to 0 dB (0.1 dB step) Threshold x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, ∞ (16 points) Ratio (x :1) Out gain 0 dB to +18 dB (0.1 dB step)
Page 9
DM1000/MB1000/SP1000 Libraries Presets 52 (EFFECT 2–4: 44) Effect library (EFFECT 1–4) User memories Presets Compressor library User memories Presets Gate library User memories Presets EQ library User memories Presets Channel library User memories Presets Surround Monitor library User memories Presets...
Page 10
DM1000/MB1000/SP1000 Digital Input Spec Input Format Data length Level Connector XLR-3-31 type (Balanced) * AES/EBU 24-bit RS422 2TR IN DIGITAL 0.5 Vpp/75 Ω IEC-60958 24-bit Phono 1. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD). Digital Output Spec Output Format...
Page 11
DM1000/MB1000/SP1000 I/O Slot Spec (1-2) Each I/O SLOT accepts a digital interface card. SLOT #1 has a serial interface. OUTPUT number of Maker Model Function INPUT Format Resolution Frequency Note Available cards Can handle MY8-AT Digital I/O ADAT 20 bit 44.1/48 kHz...
DM1000/MB1000/SP1000 REMOTE Port Signal Signal RX+/GND * RX–/RX– * RTS/RX+ * TX–/TX+ * CTS/TX– * TX+/GND * N.C. 1. RS422 (for AD824)/SONY 9 pin protocol (P2) CONTROL Port Signal Signal GPO0 GPO1 GPO2 GPO3 GPO4 GPO5 GPO6 GPO7 GPI0 GPI1...
Page 13
DM1000/MB1000/SP1000 DIMENSIONS Top view Front view Side view Units: mm With MB1000 and SP1000 installed Top view Front view Side view Units: mm...
Page 16
DM1000/MB1000/SP1000 STEREO Section AUTO q [AUTO] button w [SEL] button e [ON] button r [STEREO] fader STEREO AUX SELECT Section AUX SELECT DISPLAY q [DISPLAY] button w [AUX 1]–[AUX 8] buttons ENCODER MODE Section ENCODER MODE q [DISPLAY] button DISPLAY...
Page 17
DM1000/MB1000/SP1000 DISPLAY ACCESS Section q [AUTOMIX] button w [DIO] button e [SETUP] button r [UTILITY] button DISPLAY ACCESS t [MIDI] button y [REMOTE] button AUTOMIX SETUP UTILITY u [METER] button MIDI REMOTE METER VIEW i [VIEW] button o [PAIR/GROUP] button...
Page 18
DM1000/MB1000/SP1000 SELECTED CHANNEL Section q ROUTING [DISPLAY] button w ROUTING [1]–[8] buttons SELECTED CHANNEL e ROUTING [STEREO] button ROUTING EQUALIZER r ROUTING [DIRECT] button DISPLAY DISPLAY t EQUALIZER [DISPLAY] button HIGH y EQUALIZER [HIGH] button u EQUALIZER [HIGH-MID] button HIGH MID...
Page 19
DM1000/MB1000/SP1000 USER DEFINED KEYS Section USER DEFINED KEYS DISPLAY q [DISPLAY] button w [1]-[12] buttons Data Entry Section q Parameter wheel w [ENTER] button e [DEC] & [INC] buttons r Left, Right, Up, Down cursor buttons ENTER Headphones & Talkback Section...
DM1000/MB1000/SP1000 MONITOR Section q [DISPLAY] button MONITOR w [SOLO] indicator DISPLAY e [CLEAR] button r [2TR D1] button SOLO CLEAR t [2TR D2] button 2TR D2 STEREO 2TR D1 y [STEREO] button u [SLOT] button SLOT i [BUS] button MONITOR...
Page 21
DM1000/MB1000/SP1000 SLOT Section SLOT SLOT q [SLOT 1] & [SLOT 2] Digital I/O & Control Section METER SMPTE IN REMOTE MIDI TO HOST WORD CLOCK 2TR IN DIGITAL CONTROL AES/EBU COAXIAL COAXIAL AES/EBU q [METER] connector w [CONTROL] connector e [SMPTE TIME CODE INPUT] connector r [REMOTE] connector t [MIDI IN &...
Page 22
DM1000/MB1000/SP1000 MB1000 Controls q Channel indicators w [INPUT METERING POSITION] indicators e [OUTPUT METERING POSITION] indicators r [PEAK HOLD] button t [TIME CODE] display y [1-16] / [17-32] / [33-48] / [REMOTE 1] / [REMOTE 2] / [MASTER] buttons u Level meters...
(See page 150.) Disassembling the DM1000 Removing the SP1000 (Time required: About 2 minutes) 1-1. If the SP1000 is attached to the DM1000, remove the ten (10) screws marked [A], and then both sides must be removed. (Fig.1) DM1000 SP1000...
Page 29
DM1000/MB1000/SP1000 Rear Assembly U (Time required: About 9 minutes) 4-1. Remove the SP1000. (See procedure 1.) 4-2. Remove the MB1000. (See procedure 2.) 4-3. Fasten the control panel assembly. (See procedure 3.) 4-4. Remove the six (6) screws marked [40A] and the two (2) screws marked [70A].
Page 30
DM1000/MB1000/SP1000 Bottom Assembly Section DCD Circuit Board (Time required: About 8 minutes) 5-1. Remove the SP1000. (See procedure 1.) 5-2. Remove the MB1000. (See procedure 2.) 5-3. Fasten the control panel assembly. (See procedure 3.) 5-4. Remove the four (4) screws marked [410] and the two (2) screws marked [411].
Page 31
DM1000/MB1000/SP1000 MAIN Circuit Board (Time required: About 12 minutes) 9-1. Remove the SP1000. (See procedure 1.) 9-2. Remove the MB1000. (See procedure 2.) 9-3. Fasten the control panel assembly. (See procedure 3.) 9-4. Remove the rear assembly U. (See procedure 4-5.) 9-5.
Page 33
DM1000/MB1000/SP1000 <Top view> [130A] AC shield plate MAIN [285] [12C] [60B] Power transformer Lithium Battery Battery VN103500 VN103600(Battery holder for VN103500) Notice for back-up battery removal Push the battery as shown in figure, then the battery will pop up. Druk de batterij naar beneden zoals aangeven in de tekening de batterij springt dan naar voren.
Page 34
DM1000/MB1000/SP1000 AC Shield Plate (Time required: About 10 minutes) 13-1. Remove the SP1000. (See procedure 1.) 13-2. Remove the MB1000. (See procedure 2.) 13-3. Fasten the control panel assembly. (See procedure 3.) 13-4. Fasten the rear assembly U. (See procedure 4-4.) 13-5.
Page 35
DM1000/MB1000/SP1000 [265]: Cord holder (underneath the ferrite core) [255] Locking card spacer Ferrite core [290A] Power switch knob [255]: Bind Head Tapping Screw-B 3.0X6 MFZN2BL (EP600230) Photo.9 [290A]: Bind Head Tapping Screw-S 4.0X8 MFZN2BL (VI693100) Photo.8 [290B] [290B]: Bind Head Tapping Screw-S 4.0X8 MFZN2BL (VI693100)
Page 36
DM1000/MB1000/SP1000 Rear Assembly U Section ADA Circuit Board (Time required: About 10 minutes) 17-1. Remove the SP1000. (See procedure 1.) 17-2. Remove the MB1000. (See procedure 2.) 17-3. Fasten the control panel assembly. (See procedure 3.) 17-4. Fasten the rear assembly U. (See procedure 4-4.) 17-5.
Page 38
DM1000/MB1000/SP1000 Heat Sink (Time required: About 8 minutes) 19-1. Remove the SP1000. (See procedure 1.) 19-2. Remove the MB1000. (See procedure 2.) 19-3. Fasten the control panel assembly. (See procedure 3.) 19-4. Remove the two (2) screws marked [70A]. (Fig.2) 19-5.
Page 39
DM1000/MB1000/SP1000 <Top view> <Top view> HAAD HAAD HAAD Button assembly x16 Knob spacer x18 Photo.13 [60C]: Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Fig.7 [60C] Control Panel Assembly Section When removing the circuit board, if it is hard to handle while the control panel assembly is fixed slantwise at the stay, open it widely at 180°...
Page 40
DM1000/MB1000/SP1000 LCD Circuit Board (Time required: About 8 minutes) 24-1. Remove the SP1000. (See procedure 1.) 24-2. Remove the MB1000. (See procedure 2.) 24-3. Fasten the control panel assembly. (See procedure 3.) 24-4. Remove the two (2) screws marked [120B] and the two (2) screws marked [170].
Page 43
DM1000/MB1000/SP1000 (Time required: About 10 minutes) 27-1. Remove the SP1000. (See procedure 1.) 27-2. Remove the MB1000. (See procedure 2.) 27-3. Fasten the control panel assembly. (See procedure 3.) 27-4. Remove the LCD shield plate. (See procedure 24-4.) 27-5. Remove the PN1 (2/4 meter) circuit board.
Page 44
DM1000/MB1000/SP1000 Disassembling the MB1000 Rear Panel (Time required: About 3 minutes) 28-1. Remove the MB1000. (See procedure 2.) 28-2. Remove the sixteen (16) screws marked [40C]. The rear panel can then be removed from the front panel. (Fig.10) PN Circuit Board (Time required: About 4 minutes) 29-1.
Page 45
DM1000/MB1000/SP1000 Front panel <Right side view> <Front view> <Left side view> <Bottom view> [40C] [40C] [40C] <Rear view> Rear panel [40C]: Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190) Fig.10 [50] <Rear view> Cable holder [70C] MAIN <Front view> [70B] Meter angle L...
INSTALLING AN OPTIONAL CARD Follow the steps below to install an optional mini-YGDAI card. 1 Make sure that the power to the DM1000 is turned off. 2 Undo the two fixing screws and remove the slot cover, as shown below.
DM1000/MB1000/SP1000 LSI PIN DESCRIPTION DM1000 M37641M8-141FP (X2485200) CPU (USB 32K) ................47 HD6417709SF133 (X2081A00) CPU (SH-3) ................. 48 SH7042 (X4409A00) CPU (SUB) ....................49 MBCG46183-129PFV-G (XV833A00) Gate Array (SIO4) ............50 SGH603064F-62F (XV973A00) Gate Array .................. 50 YSS910-S (XV988A00) DSP6 (Digital Signal Processor) ............51 YSS919B-H (XZ693B00) DSP7 (Digital Signal Processor) ............
Page 48
DM1000/MB1000/SP1000 HD6417709SF133 (X2081A00) CPU (SH3) MAIN: IC001 NAME FUNCTION NAME FUNCTION CKE/PTK5 CK enable / Port K Mode control RAS3L/PTJ0 RAS address bus / Port J Vcc(RTC) Power supply +1.8 V PTJ1 Port J XTAL2 CASL/PTJ2 CAS address bus / Port J...
Page 49
DM1000/MB1000/SP1000 SH7042 (X4409A00) CPU (SUB) FD: IC203 NAME FUNCTION NAME FUNCTION PE14 Port E PE15 Data bus Ground Ground Data bus Power supply +5V Address bus Data bus Ground XTAL Crystal oscillator Mode control EXTAL Crystal oscillator Mode control Non-maskable interrupt request...
Page 50
DM1000/MB1000/SP1000 MBCG46183-129PFV-G (XV833A00) Gate Array (SIO4) MAIN: IC651 NAME FUNCTION NAME FUNCTION TX31 Transmit Data 31 Data Bus RX32 Receive Data 32 TX32 Transmit Data 32 /IRQ0 Interrupt Request Port 0 RX33 Receive Data 33 /IRQ1 Interrupt Request Port 1...
Page 51
DM1000/MB1000/SP1000 YSS910-S (XV988A00) DSP6 (Digital Signal Processor) MAIN: IC301-304 NAME FUNCTION NAME FUNCTION Power supply (3.3 V) Ground Ground DB13 System master clock input (60 MHz or 30 MHz) DB14 System master clock output (High or 30 MHz) DB15 Vdd5...
Page 52
DM1000/MB1000/SP1000 YSS919-H (XZ693A00) DSP7 (Digital Signal Processor) MAIN: IC201-206 NAME FUNCTION NAME FUNCTION PLLEN PLL enable input (0: PLL unuse, 1: PLL use) SIO32 /TEST Test mode setting (0: TEST, 1: Normal) SIO33 AVss Analog ground SIO34 PLL filter SIO35...
Page 53
DM1000/MB1000/SP1000 MBCG61594-130 (X3299A00) ATSC2A MAIN: IC501, 502 NAME FUNCTION NAME FUNCTION Power supply +3.3V Power supply +3.3V XTST LSI test pin PB_H_M4_SEL Port B audio data input buffer active select Ground PB_O_MUTE Port B mute WT_X CPU interface write input...
Page 54
DM1000/MB1000/SP1000 YM3436DK (XG948E0) DIR2 (Digital Format Interface Receiver) MAIN: IC144 NAME FUNCTION NAME FUNCTION DAUX Auxiliary input for audio data RSTN System reset input HDLT Asynchronous buffer operation flag Vdda VCO section power (+5V) DOUT Audio data output CTLN VCO control input N...
Page 55
DM1000/MB1000/SP1000 S1D13704F00A100 (X3498A00) LCDC (LCD Controller) MAIN: IC027 NAME FUNCTION NAME FUNCTION COREV Power supply +3.3V COREV Power supply +3.3V /WAIT Wait signal DRDY TFT/D-TFD display enable DB15 LCDPWR LCD power control DB14 TESTEN Test enable input DB13 CNF4 DB12...
Page 56
DM1000/MB1000/SP1000 ICS2008BV-T (X2832B00) T.C. Reader/Generator JK1: IC254 NAME FUNCTION NAME FUNCTION INTR Interrupt request Clear to send RESET Master reset UART transmit data FRAME Color frame A / B input Ready to send CLICK LTC SYNC input LRCLK SMPTE LTC receive clock...
Page 57
DM1000/MB1000/SP1000 MB1000 SH7042 (X4409A00) CPU (SH-2) MAIN: IC106 NAME FUNCTION NAME FUNCTION PE14 Port E PE15 Data bus Ground Ground Data bus Power supply +5V Address bus Data bus Ground XTAL Crystal oscillator Mode control EXTAL Crystal oscillator Mode control...
Page 66
DM1000/MB1000/SP1000 POWER ON/OFF DCCOM (AC) Circuit Board to AC Inlet Assembly to Power Transformer to Bottom Chassis (for ground) Component side DCCOM (DCA 2/5) Circuit Board DCCOM (DCA 3/5) Circuit Board to DCA 1/5-IC302 to DCA 1/5-IC301 Component side Component side...
Page 67
DM1000/MB1000/SP1000 DCCOM (DCA 1/5) Circuit Board to DCA 4/5 -CN403 to DCA 3/5 -CN402 to FD-CN202 to DCA 2/5 -CN401 Power Transformer to HAAD 1/2 -CN952 to ADA -CN954 to OPT -CN807 to JK1-CN653 Component side 2NAP-V990110-2 (J, U, V models)
Page 68
DM1000/MB1000/SP1000 DCD Circuit Board to MAIN-CN006 not installed to FD-CN201 to PN1 (1/4)-CN105 Power Transformer Component side 2NAP-V990130-2...
Page 69
DM1000/MB1000/SP1000 DCD Circuit Board Pattern side 2NAP-V990130-2...
Page 71
DM1000/MB1000/SP1000 to DCA 1/5-CN306 to PN1 (1/4)-CN104 to PN1 (1/4)-CN103 to DCD-CN202 fader 10 fader 11 fader 12 fader 13 fader 14 fader 15 fader 16 fader STEREO fader Component side 2NAP-V989990-2...
Page 72
DM1000/MB1000/SP1000 FD Circuit Board to DCA 1/5-CN306 to PN1 (1/4)-CN104 to DCD-CN202 to PN1 (1/4)-CN103 2NAP-V989990-3...
Page 73
DM1000/MB1000/SP1000 to PN1 (1/4)-CN102 to PN1 (1/4)-CN101 to MAIN-CN003 installed Pattern side 2NAP-V989990-3...
Page 74
DM1000/MB1000/SP1000 HACOM (ADA) Circuit Board to MAIN-CN901 to XLR-CN151 to XLR-CN551 HACOM (ADA) Circuit Board 2NAP-V989910-2 2NAP-V989910-3...
Page 75
DM1000/MB1000/SP1000 to DCA 1/5-CN305 to XLR-CN951 to XLR-CND51 Component side Pattern side 2NAP-V989910-2 2NAP-V989910-3...
Page 76
DM1000/MB1000/SP1000 HACOM (HAAD 1/2) Circuit Board to XLR-CN101 to XLR-CN501 PAD 20dB 1 PAD 20dB 2 PAD 20dB 3 PAD 20dB 4 PAD 20dB 5 PAD 20dB 6 PAD 20dB 7 PAD 20dB 8 PAD 20dB 9 PAD 20dB 10...
Page 77
DM1000/MB1000/SP1000 to XLR-CN901 to XLR-CND01 20dB 10 PAD 20dB 11 PAD 20dB 12 PAD 20dB 13 PAD 20dB 14 PAD 20dB 15 PAD 20dB 16 TALKBACK LEVEL to HAAD 2/2 -CN003 PHONES GAIN 10 GAIN 11 GAIN 12 GAIN 13...
Page 79
DM1000/MB1000/SP1000 Pattern side 2NAP-V989910-3...
Page 80
DM1000/MB1000/SP1000 JKCOM (JK1) Circuit Board to DCA 1/5-CN307 to MAIN-CN651 SMPTE IN MIDI IN/OUT REMOTE CONTROL to MAIN-CN652 TO HOST USB AES/EBU AES/EBU COAX WORD CLOCK 2TR IN/OUT DIGITAL JKCOM (JK2) Circuit Board Component side to MAIN-CN701 Component side 2NAP-V989800-2...
Page 81
DM1000/MB1000/SP1000 JKCOM (JK1) Circuit Board Pattern side JKCOM (JK2) Circuit Board Pattern side 2NAP-V989800-2...
Page 82
DM1000/MB1000/SP1000 JKCOM (OPT) Circuit Board to MAIN-CN801 SLOT1 to MAIN-CN802 to DCA 1/5-CN302 to MAIN-CN803 SLOT2 to MAIN-CN804 Component side 2NAP-V989800-2...
Page 83
DM1000/MB1000/SP1000 JKCOM (OPT) Circuit Board Pattern side 2NAP-V989800-2...
Page 84
DM1000/MB1000/SP1000 MAIN Circuit Board to FD-CN203 not used (for check) to LCD -CN501 to DCD-CN203 to HAAD 1/2-CN951 to ADA-CN953 Lithium Battery Battery VN103500 VN103600(Battery holder for VN103500) Notice for back-up battery removal Battery Push the battery as shown in figure, then the battery will pop up.
Page 85
DM1000/MB1000/SP1000 to OPT-CN802 to OPT -CN801 to JK1 -CN652 to JK1 -CN651 to JK2 -CN701 to OPT-CN804 to OPT-CN803 Component side 2NAP-V989750-2...
Page 86
DM1000/MB1000/SP1000 MAIN Circuit Board 2NAP-V989750-2...
Page 87
DM1000/MB1000/SP1000 Component side 2 layer 2NAP-V989750-2...
Page 88
DM1000/MB1000/SP1000 MAIN Circuit Board 2NAP-V989750-2...
Page 89
DM1000/MB1000/SP1000 Component side 5 layer 2NAP-V989750-2...
Page 90
DM1000/MB1000/SP1000 MAIN Circuit Board 2NAP-V989750-3...
Page 91
DM1000/MB1000/SP1000 Pattern side 2NAP-V989750-3...
Page 92
DM1000/MB1000/SP1000 PNCOM (PN1 (1/4)) Circuit Board to FD-CN403 to FD-CN404 2NAP-V990000-2...
Page 93
DM1000/MB1000/SP1000 to PN1 (2/4)-CN401 to PN1 (3/4)-CN109 to PN1 (4/4) -CN111 to DCD -CN204 to PN2 -CN301 to FD-CN401 to FD-CN402 Component side 2NAP-V990000-2...
Page 95
DM1000/MB1000/SP1000 Pattern side 2NAP-V990000-2...
Page 96
DM1000/MB1000/SP1000 PNCOM (PN1 (2/4)) Circuit Board LCD contrast Component side to LCD-CN503 to PN1 (1/4)-CN107 Pattern side PNCOM (PN1 (3/4)) Circuit Board PNCOM (PN1 (4/4)) Circuit Board Parameter wheel Component side Pattern side Joy stick Component side Pattern side PNCOM (PN2) Circuit Board...
Page 97
DM1000/MB1000/SP1000 PNCOM (LCD) Circuit Board LCD Module LCD Module to PN1 (2/4)-CN402 to MAIN-CN005 Component side Pattern side 2NAP-V990000-2...
Page 98
DM1000/MB1000/SP1000 XLR Circuit Board to HAAD 1/2-CND02 to HAAD 1/2-CN902 +48V ON/OFF +48V ON/OFF +48V ON/OFF +48V ON/OFF +48V ON/OFF +48V ON/OFF +48V ON/OFF 10 +48V ON/OFF 9 INPUT INPUT INPUT INPUT INPUT INPUT INPUT INPUT OMNI IN OMNI IN...
Page 99
DM1000/MB1000/SP1000 MAIN Circuit Board to PN-CN201 installed to METER (DM1000) Component side 2NAP-V990400-2...
Page 100
DM1000/MB1000/SP1000 MAIN Circuit Board Pattern side 2NAP-V990400-2...
Page 101
DM1000/MB1000/SP1000 PN Circuit Board to MAIN-CN102 Component side 2NAP-V990410-2...
Page 102
DM1000/MB1000/SP1000 PN Circuit Board Pattern side 2NAP-V990410-2...
Page 103
DM1000/MB1000/SP1000 INSPECTIONS Perform the Check of DM1000. 1-4. Fader Inspection 1. Preparations q Preparations 1-1. Parameters a. Press the LAYER [MASTER] key to select the The parameters are as follows unless otherwise master layer. specified. b. Move all the faders all the way up.
Page 104
DM1000/MB1000/SP1000 e Residual noise (OMNI OUT 1~12) y Crosstalk between left and right Parameter Switch BUS OUT Off. Parameter PAN L swung to cut off. Permissible range Input frequency Output level (L) Permitted range (R) -86dBu or below 1kHz -10dBu...
Page 105
DM1000/MB1000/SP1000 e Distortion ratio (CH 1~16) 2-5. CH IN 1~16 level meter operation check Parameters Input the regulated level to the Input frequency Output level Permissible range channels being measured. 1kHz +22dBu 0.02% or below 1~16 CH can be input at the same time.
Page 106
DM1000/MB1000/SP1000 3-3. OMNI IN 1~4 4-2. 2TR DIGITAL IN 1, 2 Parameters Inspect with OMNI OUT 1. Parameters Use Parameter System Two. q Distortion ratio (OMNI IN 1~4) For distortion measurement, select BW: 80kHz. Input frequency Output level Permissible range Inspect with OMNI OUT 1 and 2.
Page 107
DM1000/MB1000/SP1000 4-3. WORD CLOCK IN, 2TR DIGITAL IN 1 and 2 PLL 5-2. WORD CLOCK EXT operation range Parameters Select the WORD CLOCK as follows. Parameters Use Parameter System Two. WORD CLOCK IN inspection: For distortion measurement, select WC IN BW: 80kHz.
Page 108
[ENTER] switch. Set the CH 1~16 Fader to 10 dB Adjust CH1-16 +10dB 1) Connect the PC and the DM1000 with the USB and the STEREO Fader to 0 dB, STEREO 0dB cable. then press the [ENTER] switch.
DM1000/MB1000/SP1000 DM1000/MB1000 SERVICE CHECK PROGRAM Execute the Service Check Program for DM1000 and MB1000. (Fig. 3) Outline Example B of individual check screen (when checking each 0-1. Operation method one of multiple items automatically or visually) Keys used for the service check on the panel...
Page 116
The voltage of the backup battery by A/D display the dialog box for confirmation. Select Yes is measured and judgment is automatic. and press the [ENTER] key to restart the DM1000 in the service check mode. Example of execution screen...
Page 117
DM1000/MB1000/SP1000 DSP6 test items DSP7 test items 1-13. WORD CLOCK test WORD CLOCK OUT → IN is counted by 1: CPU Interface (Data bus) 1: CPU Interface (Data Bus) Contents: 2: CPU Interface (Data bus) 2: CPU Interface (Chip Select)
Page 118
DM1000/MB1000/SP1000 1-22. PANEL LED test 1-24. PANEL SW test Contents: Visually check that the 7-segment LEDs Contents: Check that all of the switches on the panel and LEDs on the panel light in the specified respond when pressed in the specified order.
Page 119
DM1000/MB1000/SP1000 • Move all of the FADERs to the set positions 2) Explanation of the automatic judgment display of the (three positions) and the stop positions will FADER Up/Down be checked and whether or not the values “NG: CH 1, 1020, (990...1023), 980”...
Page 120
DM1000/MB1000/SP1000 Example of execution screen 1-32. METER SW test Contents: Check that the corresponding LEDs light/ If the judgment is OK or NG, turn off when the MB1000 SWs are the test continues with the check pressed. of the next channel automatically.
Page 121
DM1000/MB1000/SP1000 2. Supplement LCD display Fig. 1 Panel SW operation order screen (See SW operation Fig. 1 and 2 for operation order.) LCD display: 53 columns × 30 lines (320 × 240 dots with Font 5×7) The [DEC] SW is not displayed during the 1-24.
Page 122
DM1000/MB1000/SP1000 SW operation Fig. 1 GROUP 1 SW operation Fig. 2 GROUP 2...
Page 123
DM1000/MB1000/SP1000 LED lighting order Fig. 1 LED lighting order Fig. 2...
Page 124
Startup method While pressing the [AUX SELECT DISPLAY] and 3-1. Outline [AUX5] keys, turn the power ON. Execute the Audio Check for DM1000. Limits • Possible operation keys are for the DATA ENTRY Check method SECTION only.
Page 125
DM1000/MB1000/SP1000 MODE Changing the input/output terminals ANALOG Patches the ANALOG I/O to the input/output. SLOT 1 Patches the SLOT 1 I/O to the input/output. SLOT 2 Patches the SLOT 2 I/O to the input/output. 2TRD Patches the 2TRD 1, 2 I/O to the input/output.
Page 128
DM1000/MB1000/SP1000 CH40 SLOT2-8 CH41 SLOT2-9 CH42 SLOT2-10 CH43 SLOT2-11 CH44 SLOT2-12 CH45 SLOT2-13 CH46 SLOT2-14 CH47 SLOT2-15 CH48 SLOT2-16 MODE: Patch setting during 2TRD INPUT CH IN PORT OUTPUT CH(BUS/AUX) OUT PORT 2TRD1L BUS1 2TRD1L 2TRD1R BUS2 2TRD1R 2TRD2L BUS3...
Page 129
--- PANEL ALL LED --- 1 BRIGHTNESS NG 2 RED LEDs OK 3 GREEN LEDs OK 4 ORANGE LEDs EXIT ([DEC] Key->[ENTER] Key) --- DM1000 test --- (C)YAMAHA 2003 F/W Ver. MAIN Vx.xx METER Vx.xx SUB1 Vx.xx PLLP2 OK 22 PANEL LED...
Page 130
DM1000/MB1000/SP1000 --- PLLP2 --- Adrs,Data BUS EXIT ([DEC] Key->[ENTER] Key) --- BATT --- DM1000 2TR IN DIGITAL1 2TR IN DIGITAL2 BATT NG:BATT (2.56V) 2TR OUT DIGITAL1 2TR OUT DIGITAL2 EXIT ([DEC Key]->[ENTER Key]) WORD CLOCK IN WORD CLOCK OUT TO HOST-USB...
Page 132
DM1000/MB1000/SP1000 --- PANEL LED --- 1 CH1...CH16 PEAK-SIGNAL OK 2 AUX SELECT..FADER MODE OK 3 CH1..CH16 SEL-SOLO-ON, STEREO AUTO-SEL-ON OK 4 ROUTING..SCENE MEMORY OK 5 MONITOR OK 6 LAYER..USER DEFINED KEYS OK 7 STEREO METER OK 8 ALL LED ON...
Page 133
DM1000/MB1000/SP1000 --- FADER Move --- 1 FADER Up Position OK 2 FADER Down Position OK 3 FADER Up NG 4 FADER Down OK 5 FADER Position1 OK 6 FADER Position2 OK 7 FADER Position3 [ENTER] key to Start FADER Up EXIT ([DEC] Key->[ENTER] Key)
Preparation 1) Connect the D-sub 15-pin cable to the [METER] terminal on the rear of the DM1000. 2) If there is no DM1000, supply +16.5 V power with an external power supply to the +12V terminal and the ground terminal.
• You can also store the data to an external MIDI device, such as a MIDI data filer, by using MIDI Bulk Dump. (See page 146.) 1 Make sure that the power to the DM1000 is turned off. 2 While holding down the SCENE MEMORY [STORE] button, turn on the POWER ON/OFF switch.
TRANSMITTING PARAMETER SETTINGS VIA MIDI (BULK DUMP) You can back up data stored in the DM1000, such as libraries and Scenes, to an external MIDI device by using MIDI Bulk Dump. In this way, you can later restore previous DM1000 settings by transmitting this MIDI data back to the DM1000.
Page 147
Note: Data selected by the SETUPMEM button includes MIDI transmission and reception port settings and message settings. After you store to an external device bulk dump data that has its reception disabled, if the DM1000 later starts to receive this particular data, DM1000 bulk dump reception will be turned off immediately, and the DM1000 will be unable to receive subsequent data.
You can correct the shifted faders using the Calibration function. 1 Make sure that the power to the DM1000 is turned off. 2 While holding down the [ENTER] button, turn on the POWER ON/OFF switch.
127 (7F) Active sense Command rx/tx function * ‘tx’ indicates that the data can be transmitted from the DM1000, and F0 7F dd 06 … F7 MMC MMC command ‘rx’ indicates that the data can be received by the DM1000. COMMAND F0 7F dd 07 …...
However if [OMNI] is ON, they will be received regardless of the These messages are transmitted when the Machine Control section of the channel. When a message is received, a Scene Memory will be recalled according DM1000 is operated. to the settings of the [Program Change Table]. Transmission 2.12.2 BULK DUMP...
Page 153
2.12.2.3 Setup memory bulk dump format words of 7-bit data. Of the setup memory of the DM1000, this bulk-dumps data other than the User Conversion from actual data into bulk data define layer, User define plug-in, User define keys, Control change table, and d[0~6]: actual data Program change table.
Page 154
0bbbbbbb bb System exclusive message STATUS 11110000 F0 total block number(minimum number is 0) BLOCK INFO. 0ttttttt tt Manufacture’s ID number (YAMAHA) ID No. 01000011 43 current block number(0-total block number) 0bbbbbbb bb n=0-15 (Device number=MIDI Channel) SUB STATUS 0010nnnn 2n User define layer data of block[bb]...
Page 155
256 and following are data for the corresponding channel of the edit buffer. ee=(Invert(‘L’+…+de)+1)&0x7F CHECK SUM 0eeeeeee ee For reception by the DM1000, only the user area is valid. (40-199, 256-) End of exclusive 11110111 F7 System exclusive message STATUS 11110000 F0 Manufacture’s ID number (YAMAHA)
Page 156
256 and following are data for the corresponding channel of the edit buffer. current block number(0-total block number) 0bbbbbbb bb For reception by the DM1000, only the user area is valid. (36-127, 256-) GATE Library data of block[bb] DATA 0ddddddd ds...
Page 157
0:Library no.0 – 32:Library no.32, 256:current input patch data, 8192:UNDO Manufacture’s ID number (YAMAHA) ID No. 01000011 43 For reception by the DM1000, only the user area is valid. (1-32, 256, 8192) n=0-15 (Device number=MIDI Channel) SUB STATUS 0010nnnn 2n System exclusive message...
Page 158
The second and third bytes of the DATA NAME indicate the library number. ‘C’ 0:Library no.0 – 32:Library no.32, 256:current data, 8192:UNDO 01000011 43 For reception by the DM1000, only the user area is valid. (1-32, 256, 8192) ‘9’ 00111001 39 ‘1’...
Page 159
System exclusive message BLOCK INFO. 0bbbbbbb bh STATUS 11110000 F0 0bbbbbbb bl Manufacture’s ID number (YAMAHA) ID No. 01000011 43 total block number(minimum number is 0) 0ttttttt th n=0-15 (Device number=MIDI Channel) SUB STATUS 0000nnnn 0n 0ttttttt tl FORMAT No.
Page 160
2.12.3.1.2 Parameter Change basic format (Universal 2.12.3.3 Parameter request (Edit buffer) format) System exclusive message STATUS 11110000 F0 System exclusive message Manufacture’s ID number (YAMAHA) STATUS 11110000 F0 ID No. 01000011 43 Manufacture’s ID number (YAMAHA) n=0-15 (Device number=MIDI Channel) ID No.
Page 161
(such as bulk re- ception) Reception (only transmitted by the DM1000) This message is echoed if [Parameter change ECHO] is ON. Data received from a port that is assigned to [Cascade Link] and whose Device 2.12.3.12.1 Parameter change (Function call response:...
Page 162
When the title is changed on the DM1000, this message will be transmitted with Transmission the device number set to [Tx CH]. When a memory or library is cleared on the DM1000, this message will be trans- mitted with the device number set to [Tx CH]. STATUS...
Page 163
ECHO] is ON. STATUS 11110000 F0 System exclusive message When this is received, the patch link data of the specified scene will be modified. Manufacture’s ID number (YAMAHA) ID No. 01000011 43 Transmission n=0-15 (Device number=MIDI Channel) SUB STATUS 0001nnnn 1n...
Page 164
SUB STATUS 0001nnnn 1n 2.12.3.26 Parameter change (Sort Table) MODEL ID (digital mixer) GROUP ID 00111110 3E When scene memory sort is executed on the DM1000, the memory sort table DM1000 MODEL ID 00001100 0C will be transmitted to Studio Manager. Remote meter...
Page 165
11110111 F7 data is transmitted continuously while the transmission is enabled, even when the Automix Status on the DM1000 has been changed. 2.12.3.31 Parameter change (Remote Time Counter) Transmission will be disabled if the power is turned off and on again, or if the When transmission is enabled by receiving a Request of Remote Time Counter, PORT setting is changed.
DIGITAL PRODUCTION CONSOLE PARTS LIST CONTENTS OVERALL ASSEMBLY ..........2 BOTTOM ASSEMBLY ........5 REAR ASSEMBLY U ........9 CONTROL PANEL ASSEMBLY ....12 ELECTRICAL PARTS ........17-69 Notes : DESTINATION ABBREVIATIONS A : Australian model M : South African model B : British model O : Chinese model C : Canadian model...
Page 168
Rear assembly U: See page 9. Control panel assembly: See page 12. Bottom assembly: See page 5. U,V models only DIGITAL PRODUCTION CONSOLE MODEL DM1000 RISK OF ELECTRIC SHOCK 120V 135W 60Hz DO NOT OPEN MADE IN JAPAN AVIS RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
Page 169
DM1000 Pic.2 Pic.1 MAIN-JK1 wiring Control panel assembly: See page 12. Bottom assembly: See page 5. Rear assembly U: See page 9.
Page 206
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK R133 V I 1 9 4 9 0 0 Metal Film Resistor (chip) 1.0K 1/10 D R135 V I 1 9 5 6 0 0 Metal Film Resistor (chip) 2.0K 1/10 D...
Page 208
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK R376 V I 1 9 7 4 0 0 Metal Film Resistor (chip) 10.0K 1/10 D R377 V I 1 9 8 1 0 0 Metal Film Resistor (chip) 20.0K 1/10 D...
Page 209
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK R509 RD254100 Carbon Resistor (chip) 10.0 0.1 J R510 RD254100 Carbon Resistor (chip) 10.0 0.1 J R511 V I 1 9 9 0 0 0 Metal Film Resistor (chip) 47.0K 1/10 D...
Page 210
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK R620 V I 1 9 7 3 0 0 Metal Film Resistor (chip) 9.1K 1/10 D R621 V I 1 9 7 3 0 0 Metal Film Resistor (chip) 9.1K 1/10 D...
Page 211
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK -754 RD259100 Carbon Resistor (chip) 1.0M 0.1 J R755 V I 1 9 7 4 0 0 Metal Film Resistor (chip) 10.0K 1/10 D -758 V I 1 9 7 4 0 0 Metal Film Resistor (chip) 10.0K 1/10 D...
Page 212
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK R884 RD255100 Carbon Resistor (chip) 100.0 0.1 J -889 RD255100 Carbon Resistor (chip) 100.0 0.1 J R890 V I 1 9 7 4 0 0 Metal Film Resistor (chip) 10.0K 1/10 D...
Page 213
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK RA16 V I 1 9 5 7 0 0 Metal Film Resistor (chip) 2.2K 1/10 D RA17 V I 1 9 0 7 0 0 Metal Film Resistor (chip) 18.0 1/10 D...
Page 214
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK RC32 V I 1 9 6 9 0 0 Metal Film Resistor (chip) 6.2K 1/10 D RC33 V I 1 9 4 9 0 0 Metal Film Resistor (chip) 1.0K 1/10 D...
Page 215
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK RF11 V I 1 9 9 0 0 0 Metal Film Resistor (chip) 47.0K 1/10 D RF12 V I 1 9 9 0 0 0 Metal Film Resistor (chip) 47.0K 1/10 D...
Page 216
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK TR101 I C 2 2 4 0 3 0 Transistor 2SC2240 GR,BL TR102 I C 2 2 4 0 3 0 Transistor 2SC2240 GR,BL TR151 VK432900 Transistor 2SD1915(F) S,T -154 VK432900 Transistor...
Page 224
DM1000 PART NO. DESCRIPTION REMARKS REF NO. RANK R166 RD357470 Carbon Resistor (chip) 47.0K 63M J R167 V I 1 9 6 1 0 0 Metal Film Resistor (chip) 3.3K 1/10 D R168 V I 1 9 6 1 0 0 Metal Film Resistor (chip) 3.3K 1/10 D...
Page 236
PEAK METER BRIDGE MB1000 PARTS LIST CONTENTS OVERALL ASSEMBLY ..........2 FRONT PANEL ASSEMBLY ....4 REAR PANEL ASSEMBLY ......5 ELECTRICAL PARTS ........6-12 Notes : DESTINATION ABBREVIATIONS A : Australian model M : South African model B : British model O : Chinese model C : Canadian model Q : South-east Asia model...
Page 237
MB1000 OVERALL ASSEMBLY Rear panel assembly: See page 5. PEAK METER BRIDGE PEAK METER BRIDGE Front panel assembly: See page 4. MODEL MB1000 MODEL MB1000 UPC label MADE IN JAPAN MADE IN JAPAN SER.NO. J model Y model Front panel assembly: See page 4.
Page 238
MB1000 Accessories DM1000 MB1000 MB1000 Rack angle Side of Meter Bridge PART NO. DESCRIPTION REMARKS REF NO. RANK OVERALL ASSEMBLY MB1000 (V969000) Front Panel Assembly (V969010) Rear Panel Assembly (V969020) V 9 6 9 1 0 0 0 Panel Sheet...
MB1000 FRONT PANEL ASSEMBLY See page 7 for the buttons of the PN circuit board. A view PART NO. DESCRIPTION REMARKS REF NO. RANK FRONT PANEL ASSEMBLY MB1000 (V969010) V 9 6 9 0 3 0 0 Front Panel Adhesive Tape #500 W=3 (VE36240) V 6 1 8 0 0 0 0...
Page 248
WOODEN SIDE PANELS SP1000 PARTS LIST CONTENTS OVERALL ASSEMBLY ........2 Notes : DESTINATION ABBREVIATIONS A : Australian model M : South African model B : British model O : Chinese model C : Canadian model Q : South-east Asia model D : German model T : Taiwan model E : European model...
Page 249
SP1000 OVERALL ASSEMBLY DM1000 MB1000 Side pad MB side pad Bind head screw VA314000 PART NO. DESCRIPTION REMARKS REF NO. RANK OVERALL ASSEMBLY SP1000 Overall Assembly (WA47920) Overall Assembly (WA47930) VA314000 Bind Head Screw PW 4.0X20 MFZN2BL WA176400 Side Pad L...
Page 252
DM1000 BLOCK DIAGRAM 003 (DM1000) INS SEND 1-4 SO58 INS SEND 5-8 SO59 OAUX1-4 IC201(208P) INS SEND 9-12 SI41 SO60 OAUX5-8 DSP7 DIRECT OUT 1-4 SI42 SO61 DIRECT OUT 5-8 SO62 OBUS1-4 DIRECT OUT 9-12 SI44 SO63 OBUS5-8 SI45 16M SDRAM...
Page 255
DM1000 BLOCK DIAGRAM 006 (DM1000) (Gain Reduction) (Out Meter) METER METER COMP INPUT PATCH PEAK METER SIGNAL INSERT INSERT INSERT x 16 +48V INPUT 1( ...48) METER [INPUT] LEVEL METER (1-16) (Gain Reduction) OUTPUT SOLO 4BAND AD 1-16 STEREO L...
Page 256
DM1000 BLOCK DIAGRAM 007 (DM1000) Analog Digital Digital Analog Analog Digital Analog INPUT MASTER MASTER OUTPUT GAIN INSERT PHASE GATE INSERT ATT. INSERT COMP DELAY LEVEL INSERT INSERT ATT. INSERT COMP INSERT DELAY PATCH PATCH Adder LEVEL dBFS Max. Max. Output...
Page 258
AC CIRCUIT DIAGRAM (DM1000) DM1000 POWER ON/OFF to Power transformer to AC Inlet Assembly Destination F101 J, U, V KB000780 T5AL 250V H, B, W, K KB000690 T2.5AL 250V Capacitor TO SERVICE PERSONNEL Critical Components Information Components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed.
Page 260
DCD CIRCUIT DIAGRAM (DM1000) DM1000 to FD-CN201 DC-DC CONVERTER to MAIN-CN006 to Power Transformer DC-DC CONVERTER to PN1 (1/4)-CN105 TO SERVICE PERSONNEL Critical Components Information Components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed.
Page 261
FD CIRCUIT DIAGRAM 002 (DM1000) DM1000 MULTIPLEXER to DCD-CN202 REGULATOR +5V SH7042 to DCA 1/5-CN306 NJM78M05DL1A(TE1)(XS534A00) REGULATOR +5V 1: INPUT 2: GND 3: OUTPUT to MAIN-CN003 BUFFER Panel and Fader Drive Control Circuit : not installed FD CIRCUIT DIAGRAM 002 (DM1000)
Page 263
FD CIRCUIT DIAGRAM 004 (DM1000) DM1000 to PN1 (1/4)-CN101 to PN1 (1/4)-CN103 D-FF D-FF DECODER to PN1 (1/4)-CN102 to PN1 (1/4)-CN104 D-FF D-FF TRANSCEIVER TRANSCEIVER Panel (LED sink/source driver) Interface Circuit TRANSCEIVER FD CIRCUIT DIAGRAM 004 (DM1000) 28CC1-8826690-4...
Page 264
FD CIRCUIT DIAGRAM 005 (DM1000) DM1000 MULTIPLEXER MULTIPLEXER D-FF D-FF D-FF DECODER Fader Position Data and Motor Drive Permission Circuit FD CIRCUIT DIAGRAM 005 (DM1000) 28CC1-8826690-5...
Page 265
FD CIRCUIT DIAGRAM 006 (DM1000) DM1000 OP AMP MULTIPLEXER D-FF OP AMP OP AMP OP AMP OP AMP OP AMP MULTIPLEXER OP AMP OP AMP OP AMP MULTIPLEXER OP AMP : Ceramic Capacitor Motor Drive Position Instruction Circuit FD CIRCUIT DIAGRAM 006 (DM1000)
Page 267
FD CIRCUIT DIAGRAM 008 (DM1000) DM1000 REGULETOR +12V REGULETOR +12V 7 fader 10 fader OP AMP OP AMP OP AMP OP AMP 8 fader 11 fader OP AMP OP AMP OP AMP OP AMP 9 fader 12 fader OP AMP...
Page 268
FD CIRCUIT DIAGRAM 009 (DM1000) DM1000 REGULETOR +12V REGULETOR +12V 13 fader 16 fader OP AMP OP AMP OP AMP OP AMP STEREO 14 fader fader OP AMP OP AMP OP AMP OP AMP 15 fader µPC2912T-E1(X2091A00) REGULATOR +12V OP AMP...
Page 269
FD CIRCUIT DIAGRAM 010 (DM1000) DM1000 MULTIPLEXER MULTIPLEXER MULTIPLEXER OP AMP NAND OP AMP OP AMP OP AMP OP AMP Touch Sense Detection Circuit FD CIRCUIT DIAGRAM 010 (DM1000) 28CC1-8826690-10...
Page 270
ADA CIRCUIT DIAGRAM 002 (DM1000) DM1000 to XLR-CN151 to XLR-CN551 to XLR-CN951 OMNI OUT OMNI OUT OMNI OUT OMNI OUT OMNI OUT OMNI OUT OMNI OUT OMNI OUT OMNI OUT OMNI OUT OMNI OUT OMNI OUT OP AMP OP AMP...
Page 271
ADA CIRCUIT DIAGRAM 003 (DM1000) DM1000 OP AMP OP AMP OMNI IN 1 OMNI IN 2 OP AMP OP AMP to XLR-CND51 OP AMP OP AMP OMNI IN 3 OMNI IN 4 OP AMP OP AMP : Metal Film Resistor...
Page 272
HAAD CIRCUIT DIAGRAM 002 (DM1000) DM1000 to DCA 1/5-CN304 to MAIN-CN902 HAAD INVERTER TRANSCEIVER REGULATOR +5V TRANSCEIVER NJM78L05UA(XJ598A00) REGULATOR +5V 1: OUTPUT 2: COMMON 3: INPUT OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP...
Page 273
HAAD CIRCUIT DIAGRAM 003 (DM1000) DM1000 HAAD OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP PAD 20dB 9...
Page 274
HAAD CIRCUIT DIAGRAM 004 (DM1000) DM1000 TALKBACK MIC IN OP AMP OP AMP MIC & SAN (VU066300) TALKBACK LEVEL NJM78L05UA(XJ598A00) REGULATOR +5V HAAD 1: OUTPUT 2: COMMON 3: INPUT HAAD PHONES OP AMP PHONES LEVEL OP AMP OP AMP REGULETOR +5V...
Page 275
JK1 CIRCUIT DIAGRAM 002 (DM1000) DM1000 LINE RECEIVER 2TR IN DIGITAL 1 AES/EBU 2TR IN/OUT DIGITAL 2 COAX R LINE DRIVER 2TR IN/OUT DIGITAL 2 COAX L 2TR OUT DIGITAL 1 AES/EBU LINE RECEIVER WORD CLOCK IN LINE DRIVER WORD CLOCK OUT...
Page 276
JK1 CIRCUIT DIAGRAM 003 (DM1000) DM1000 to HOST USB INVERTER Photo Coupler MIDI INVERTER TO HOST USB MIDI IN, OUT INVERTER JK1 CIRCUIT DIAGRAM 003 (DM1000) 28CC1-8826682-3...
Page 277
JK1 CIRCUIT DIAGRAM 004 (DM1000) DM1000 LINE DRIVER MULTIPLEXER REMOTE MULTIPLEXER INVERTER COMPARATOR SMPTE IN OP AMP T.C READER/GENERATOR D-FF CONTROL REMOTE TIME CODE IN TRANSCEIVER : Flame Proof C. Resistor CONTROL JK1 CIRCUIT DIAGRAM 004 (DM1000) 28CC1-8826682-4...
Page 278
JK1 CIRCUIT DIAGRAM 005 (DM1000) DM1000 TRANSCEIVER to MAIN-CN652 TRANSCEIVER to DCA 1/5 -CN307 TRANSCEIVER to MAIN-CN651 I/F Section TRANSCEIVER JK1 CIRCUIT DIAGRAM 005 (DM1000) 28CC1-8826682-5...
Page 279
JK2 CIRCUIT DIAGRAM (DM1000) DM1000 METER to MAIN-CN701 LINE DRIVER JK2 CIRCUIT DIAGRAM (DM1000) 28CC1-8826683-1...
Page 280
OPT CIRCUIT DIAGRAM (DM1000) DM1000 to MAIN-CN804 to MAIN-CN802 SLOT2-b SLOT2-b to DCA 1/5-CN302 SLOT2-a SLOT1-a to MAIN-CN803 to MAIN-CN801 (X3949A00) REGULATOR -15V TAB IS INPUT REGULATOR -15V 1: GND 2: INPUT 3: OUTPUT OPT CIRCUIT DIAGRAM (DM1000) 28CC1-8826681-1...
Page 284
MAIN CIRCUIT DIAGRAM 005 (DM1000) DM1000 TRANSCEIVER TRANSCEIVER INVERTER TRANSCEIVER TRANSCEIVER INVERTER NAND INVERTER SYSTEM RESET TRANSCEIVER DIR2 PLLP2 INVERTER (CLOCK SYSTEM) : Metal Film Resistor : Mylar Capacitor MAIN CIRCUIT DIAGRAM 005 (DM1000) 28CC1-8826680-5 : Film Capacitor : not installed...
Page 285
MAIN CIRCUIT DIAGRAM 006 (DM1000) DM1000 SDRAM 16M SDRAM 16M DSP7 DSP7 SDRAM 16M DSP7 DSP7 SDRAM 16M (DSP7) : Metal Film Resistor MAIN CIRCUIT DIAGRAM 006 (DM1000) 28CC1-8826680-6 : Mylar Capacitor : not installed...
Page 286
MAIN CIRCUIT DIAGRAM 007 (DM1000) DM1000 SDRAM 16M SDRAM 16M DSP7 DSP7 : Metal Film Resistor : Mylar Capacitor : not installed (DSP7) MAIN CIRCUIT DIAGRAM 007 (DM1000) 28CC1-8826680-7...
Page 287
MAIN CIRCUIT DIAGRAM 008 (DM1000) DM1000 DRAM 4M DRAM 4M DSP6 DSP6 DRAM 4M DRAM 4M DRAM 4M DRAM 4M DSP6 DSP6 DRAM 4M DRAM 4M TRANSCEIVER (DSP6) : not installed MAIN CIRCUIT DIAGRAM 008 (DM1000) 28CC1-8826680-8...
Page 289
MAIN CIRCUIT DIAGRAM 010 (DM1000) DM1000 BUFFER INVERTER (2TR Digital I/O) : Metal Film Resistor MAIN CIRCUIT DIAGRAM 010 (DM1000) 28CC1-8826680-10 : Mylar Capacitor...
Page 290
MAIN CIRCUIT DIAGRAM 011 (DM1000) DM1000 to JK2-CN701 TRANSCEIVER D-FF to JK1-CN651 to JK1-CN652 GATE ARRAY (SIO4, JK1 I/F, JK2 I/F) MAIN CIRCUIT DIAGRAM 011 (DM1000) 28CC1-8826680-11...
Page 291
MAIN CIRCUIT DIAGRAM 012 (DM1000) DM1000 TRANSCEIVER BUFFER TRANSCEIVER SLOT1-a SLOT2-b SLOT2-b SLOT1-a to OPT -CN801 to OPT -CN803 TRANSCEIVER to OPT -CN802 to OPT-CN804 (OPT I/F) BUFFER MAIN CIRCUIT DIAGRAM 012 (DM1000) 28CC1-8826680-12...
Page 292
MAIN CIRCUIT DIAGRAM 013 (DM1000) DM1000 to ADA-CN953 to HAAD 1/2-CN951 TRANSCEIVER BUFFER BUFFER (ADA I/F, HA I/F) : not installed MAIN CIRCUIT DIAGRAM 013 (DM1000) 28CC1-8826680-13...
Page 296
PN1 CIRCUIT DIAGRAM 004 (DM1000) DM1000 PN1 (1/4) SCENE MEMORY Cursor Left Cursor Up Cursor Down Cursor Right STORE Cursor Up Cursor Down RECALL <SCENE <SCENE <SCENE <SCENE MEMORY> MEMORY> MEMORY> MEMORY> SEL STEREO AUTO ON STEREO ON STEREO AUTO...
Page 298
PN1 CIRCUIT DIAGRAM 006 (DM1000) DM1000 PN1 (2/4) to PN1 (1/4)-CN107 LCD contrast to LCD-CN503 Meter LED, LCD contrast volume PN1 CIRCUIT DIAGRAM 006 (DM1000) 28CC1-8822687-6...
Page 299
PN2 CIRCUIT DIAGRAM (DM1000) DM1000 DISPLAY <USER DEFINED KEYS> <USER <USER <USER <USER DEFINED DEFINED DEFINED DEFINED KEYS> KEYS> KEYS> KEYS> <USER <USER <USER <USER DEFINED DEFINED DEFINED DEFINED KEYS> KEYS> KEYS> KEYS> to PN1 (1/4)-CN106 <USER <USER <USER <USER...
Page 300
XLR CIRCUIT DIAGRAM (DM1000) DM1000 to ADA-CN752 OMNI OUT 1 OMNI OUT 2 OMNI OUT 3 OMNI OUT 4 OMNI OUT 5 OMNI OUT 6 OMNI OUT 7 OMNI OUT 8 OMNI OUT 9 OMNI OUT 10 OMNI OUT 11...
Page 301
PEAK METER BRIDGE MB1000 CIRCUIT DIAGRAM CONTENTS BLOCK DIAGRAM ......3 OVERALL CONNECTOR CIRCUIT DIAGRAM ............4 OVERALL CIRCUIT DIAGRAM MAIN (002, 003) .............. 5 PN (002, 003) ..............7 Note: See parts list for details of circuit board component parts.
Page 302
MB1000 BLOCK DIAGRAM (MB1000) IC203-205,207-209(16P) LED Driver IC202,206(16P) LED Matrix Switch Matrix CN201 (34P) CN102 (34P) IC102(5P) IC101(5P) 3.3V REGULATOR REGULATOR IC106(112P) IC103(16P) from DM1000 CN101 (14P) Driver/ Receiver 7042A MAIN BLOCK DIAGRAM (MB1000) 28CA1-8826694-2...
Page 303
MB1000 OVERALL CONNECTOR CIRCUIT DIAGRAM (MB1000) MAIN CN201 CN102 CN101 D-Sub Cable from METER (DM1000) OVERALL CONNECTOR CIRCUIT DIAGRAM (MB1000)
Page 304
MAIN CIRCUIT DIAGRAM 002 (MB1000) MB1000 METER (DM1000) LINE TRANSCEIVER DC-DC CONVERTER to PN-CN201 LM2596SX-3.3 (X3563A00) DC-DC CONVERTER Metal DC-DC CONVERTER 1: V 2: OUTPUT 3: GROUND 4: FEEDBACK 5: ON/OFF LM2596SX-5.0 (X3564A00) DC-DC CONVERTER Metal 1: OUTPUT 2: V...
Page 305
MAIN CIRCUIT DIAGRAM 003 (MB1000) MB1000 DECODER not installed : Ceramic Capacitor : not installed SYSTEM RESET TRANSCEIVER MAIN CIRCUIT DIAGRAM 003 (MB1000) 28CC1-8826696-3...
Page 306
PN CIRCUIT DIAGRAM 002 (MB1000) MB1000 SOURCE DRIVER to MAIN-CN102 DRIVER TRANSCEIVER DRIVER DRIVER BUS1 BUS2 BUS3 BUS4 BUS5 BUS6 BUS7 BUS8 METER BUS 1-8, TIME CODE, SW PN CIRCUIT DIAGRAM 002 (MB1000) 28CC1-8826697-2...