Appendix B: Specifications; General Spec - Yamaha 006IPTO-F0 Owner's Manual

332

Appendix B: Specifications

Appendix B: Specifications

General Spec

Number of scene memories
Sampling Frequency
Signal Delay
Fader
Fader Resolution
1
Total Harmonic Distortion
(CH INPUT to OMNI OUT)
(Input Gain=Min.)
Frequency Response
(CH INPUT to OMNI OUT)
Dynamic Range
(maximum level to noise level)
2
Hum & Noise
(20 Hz–20 kHz)
Rs=150 Ω
Maximum Voltage Gain
Crosstalk
(@ 1 kHz)
Input Gain=Min.
AD Input (1–16)
Analog Input
(OMNI IN 1–4)
Option Input (SLOT 1–2)
Digital Input
(2TR IN DIGITAL 1–2)
DM1000 Version 2—Owner's Manual
99
Internal
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
Normal rate: 44.1 kHz–10% to 48 kHz+6%
External
Double rate: 88.2 kHz–10% to 96 kHz+6%
fs=48 kHz
Less than 1.6 ms CH INPUT to OMNI OUT
fs=96 kHz
Less than 0.8 ms CH INPUT to OMNI OUT
100 mm motorized with touch sense × 17
+10 to –138, –∞ dB input faders
0 to –138, –∞ dB master faders, stereo fader
Less than 0.05% 20 Hz to 20 kHz @ +14 dB into 600 Ω
fs=48 kHz
Less than 0.01% 1 kHz @ +24 dB into 600 Ω
Less than 0.05% 20 Hz to 40 kHz @ +14 dB into 600 Ω
fs=96 kHz
Less than 0.01% 1 kHz @ +24 dB into 600 Ω
20 Hz–20 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω
fs=48 kHz
20 Hz–40 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω
fs=96 kHz
110 dB typ. DA Converter (OMNI OUT)
106 dB typ. AD+DA (to OMNI OUT) @ fs=48 kHz
106 dB typ. AD+DA (to OMNI OUT) @ fs=96 kHz
–128 dB Equivalent Input Noise
–86 dB residual output noise. OMNI OUT (STEREO OUT off)
Input Gain=Max.
–86 dB (90 dB S/N) OMNI OUT
Input Pad =0 dB
(STEREO fader at nominal level and all CH INPUT faders at minimum level)
Input Pad =0 dB
–64 dB (68 dB S/N) OMNI OUT
Input Sensitivity
(STEREO fader at nominal level and one CH INPUT fader at nominal level)
=–60 dB
74 dB CH INPUT (CH1–16) to OMNI OUT (STEREO, BUS, AUX)
80 dB adjacent input channels (CH1–16)
80 dB input to output
Phantom switch
+48 V DC
Pad switch
0/20 dB attenuation
Gain control
44 dB (–60 to –16), detented
LED (red) turns on when post HA level reaches 3 dB below clipping at dig-
Peak indicator
ital domain
LED (green) turns on when post HA level reaches 20 dB below nominal at
Signal indicator
digital domain
24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over-
AD converter
sampling (fs=88.2, 96 kHz)
24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over-
AD converter
sampling (fs=88.2, 96 kHz)
Available cards
Optional digital interface cards (MY16, MY8, MY4 series)
SRC
On/off (1:3 and 3:1 maximum input to output sample rate ratio)