Vertical SBX IP 320 Installation Manual page 129

[Commands] Menu
To show the status of CO number 07:
mon> c 07
This is an example of CO line status:
Slot0, Chan0, St ate0, As cD255T255
Sl ot = 0 0 , D ev N o = 0 0, Hiway = 00, Ti meslot = 234 1cc
R X _ S um Loc = f ff f, T X _ S um Lo c ff f f
U cd 0 , S to re 0 , S en t 0
2 2 7 3 9 c 0 0 0 0 0 0 f f 0 0 0 0 0 0 f f ff f f 0 5 ff ff f f 0 1 0 0
2 2 7 3 a c 0 0 f f f f ff f f 0 0 ff 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 0 0
2 2 7 3 b c 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2 2 7 3 c c 0 0 0 0 00 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 00 0 0 0 0
2 2 7 3 d c 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0 0 0 0 0
2 2 7 3 e c 8 0 0 0 00 1 0 f f ff 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0
2 2 7 3 fc 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0
2 2 7 4 0 c 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2 2 7 4 1 c 0 0 0 0 0 0 0 0 0 7 0 0 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
2 2 7 4 2 c 0 0 0 0 f f 00 0 0 f f 0 0 f f 0 0 f f 6 4 ff 0 0 0 0 00 f f
2 2 7 4 3 c f f 0 0 0 0 00 0 0 f f ff 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 00
2 2 7 4 4 c 0 0 0 0 0 0 0 0 0 0 0 0 f f f f ff 0 0 f f 00 f f f f 0 0 f f
2 2 7 4 5 c 0 0 0 0 0 0 f f f f 0 0 ff f f f f f f ff 0 0 0 0 0 0
Monitor - STA Status
This command is used to show the status of a station connected to the SBX IP 320 system.
Conditions:
•
•
•
•
•
This command can be executed when this program is connected to the SBX IP 320
system.
If the [OK] button is clicked without entering a value in the [Enter Command Argument
Dialog], a message box displays to indicate "Empty field is not allowed".
You can cancel the command by clicking the [X] button on the top right side of the [Enter
Command Argument Dialog].
The length of the argument is limited to 6 characters.
The argument is a physical port number that starts from 0.
SBX IP 320 Installation Guide
Chapter 9: Remote Diagnostics
-
9 29