Technical Data; Charger Specifications; In∫X Battery Specifications - Ferno Integrated Patient Transport & Loading System iNX User Manual

8.1 Charger Specifications

The Ferno 24/36VDC battery charger (Figure 71) is capable
of charging the iN∫X battery either directly or through the
Integrated Charging System (ICS).
The battery charger is also capable of charging a 24 VDC
Ferno® POWERFlexx® POWERPac. See the battery charger
users' manual for details.
Charger Specification
Dimensions
Charging Cable
Operating Temperature
Storage Temperature
Weight
Input
Output
iN∫X Battery
Charging Time
POWERPac
Charging Time


Note: *Minimum charging time is for one transport, with the battery
charge maintained by ICS.
The Ferno 24/36VDC battery charger is not compatible with,
or designed to charge automobile batteries. However, the
following notice is required by CE standards:
The battery terminal not connected to the chassis must be
connected first. The second connection must be made to the
chassis, remote from the battery and fuel line. The battery
charger is then to be connected to the supply mains.
After charging, disconnect the battery charger from the supply
mains. Then remove the chassis connection and then the
battery connection.
8.2 iN∫X Battery Specifications
The iN∫X battery (Figure 72) is a rechargeable, 36-Volt
DC battery. The input port is proprietary to Ferno and is
compatible only with the Ferno battery charger.
Specifications: Ferno iN∫X Battery
Battery Type
Number of internal cells
Storage Temperature
Operating Temperature
Battery Output
Charging Time (1 transport,
charge maintained by ICS)
Charging Time (depleted)

Note: *Minimum charging time is for one transport, with the battery
charge maintained by ICS.
62

8 - TECHNICAL DATA

Imperial Metric
8.125 x 3.75 x 1.5 in 206 x 95 x 38 mm
6 feet 1.83 meter
-40°F to 113°F -40 to 45°C
32°F to 104°F 0°C to 40°C
1.7 lbs 770 g
AC 100~240V 50~60HZ, 92W
DC 39.6V 2A (LiFePO4 p/n 159-0093)
DC 29.3V 2A (Lead Acid p/n 082-2012)
15 minutes* - 1 hour, 45 minutes
1-2 hours
LEGAL NOTICE
36 VDC, LiFePO
4
(Lithium iron phosphate)
11
-40°F to 140°F (-40°C to 60°C)
-20°F to 140°F (-29°C to 60°C)
36 VDC, 2.5 Amp Hours nominal
15 minutes minimum
*
Up to 1 hour, 45 minutes
WARNING
Charging an improper battery can cause injury and
damage. Do not charge non-rechargeable batteries. The
Ferno 24/36VDC battery charger is compatible only with
the iN∫X battery or Ferno POWERPac and ICS systems.
Charge lead-acid batteries only in a well-ventilated area
(Only Ferno POWERFlexx® POWERPac batteries are lead-acid
type).
The appliance (battery charger) is not intended for use
by people (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance (battery charger).
If the supply cord is damaged, it must be replaced by
a special cord or assembly available from Ferno or an
authorized Ferno distributor or service center.
© Ferno-Washington, Inc. / 234-3622-06 / March 2019
71
72