Table To Check Various Switches In The Test Mode In Ac 5.2 - Valtra 6000 Workshop Manual

37. Autocontrol 5.2 (K41107---)
B. Table to check various switches (d01---d24) in the test mode in AC 5.2
Activate the test mode FII (see page 370/8) and select with the DPS bush buttons the correct test point and confirm the selec-
tion with the DPS push button, after which the selected point can be checked. When the checking has been done, press
again the DPS pre ---programming button, after which a new test point can be selected with DPS push buttons etc.
DIGITAL INPUT NAME
d01 (S23) DPS push buttons, up
d02 (S23) DPS push buttons, down
d03 (S45) HiShift button (test both buttons)
d04 (S25) PTO ---start, in cab
d05 (S60) Seat switch
d06 (S9) Front clutch pedal limit switch
d07 (S47)
DPS automatic gear change switch
d08 (S47) DPS auto/manual
d09 (S40)
Direction F, front controls
d10 (S41) Direction R, front controls
d11 (S51)
DPS pre ---programming button (under shut-
tle lever), front controls
d12 (S28) PTO ---speed 1 (lever in front position)
d13 (S29) PTO ---speed 2 (lever in rear position)
d14 (S3W) Seat direction (TwinTrac only)
d15 (S25) PTO rocker switch
d16 (S15) Parking brake, front controls
d17 (S1A, S2A) PTO ---start button on rear mudguard
d18 (S40)
Direction F, reverse drive controls (TwinT-
rac only) *)
d19 (S41) Direction R, reverse drive controls (TwinT-
rac only) *)
d20 (S2W)
Rear clutch pedal limit switch (TwinTrac) *)
d21 (S51) DPS pre ---programming button (TwinTrac)
*)
d22 (S15)
Parking brake, rear (TwinTrac) *)
d23 (S76) AutoTraction switch
d24 (S10, S20)
Brake pedal position (brake light switches).
Check both front pedals separately. Possi-
ble rear brake pedal has not the switch.
*) Seat must be turned rearwards.
--- If the value in the display is not 0, althought it should be according to the table above, the switch can be damaged or in short
circuit. Check, change the switch. Check the switch wires.
--- If the value in the display is not 1, althought it should be according to the table above, the switch can be damaged/wires broken/
poor contacts in connectors. Change the damaged switch. Check the switch wirings.
1. 8. 2000
F
A
d
P
C
IN DISPLAY 1
Button depressed
Button depressed
Button depressed
PTO switch in START ---
position
Driver sits on the seat
Pedal in bottom
Auto---position 1
Auto 1 or 2 on
F ---direction selected
R ---direction selected
Button depressed. Visi-
ble only for a while.
Speed selected
Speed selected
Seat rearwards
On, PTO ---start
Parking brake applied
Button depressed
F ---direction selected
R ---direction selected
Pedal in bottom
Button depressed. Visi-
bly only for a while.
Parking brake applied
AutoTraction on
Pedal in bottom
512
Model Code
371
6250-- 8950
IN DISPLAY 0
Button up
Button up
Button up
Disengaged
No signal
Pedal up
Auto---position 2
DPS manual mode (man)
Direction disengaged
Direction disengaged
Button up
Speed disengaged
Speed disengaged
Seat forwards
Disengaged
Parking brake disengaged
Button up
Direction disengaged
Direction disengaged
Pedal up
Button up
Parking brake disengaged
AutoTraction off
Pedal up
Page
8