Setting Mode Menu; Setting Clutch Pedal Ratio Index - Valtra 6000 Workshop Manual

37. Autocontrol 5.2 (K41107---)
3. Settings
Note! Different setting procedures have been shown on
pages 370/15 ---19A. If the settings of AC 5 and 5.2 differ
from each others, the settings of AC 5.2 have been shown
under code 371.
A. Setting mode FIII menu in AC 5.2
Note! Activating the setting mode menu, see page 370/14.
L PTO ratio 2 (lever in rear position)
P
PTO ratio 1 (lever in front position)
H Choocing speed unit, km/h or miles/h
F Choocing temperature unit ˚C or ˚F
A Setting driving speed parameters 2)
U 4WD automatics (on/off), on=1, off=0
16 Clutch pedal ratio index, rearards
15 Clutch pedal ratio index, forwards
14
Manual setting of PTO clutch initial pressu-
re 1)
13 Manual setting of PTO clutch pre ---filling
time
12
Manual setting of DPS3 (clutch C3) initial
pressure 1)
11 Manual setting of DPS2 (clutch C2) initial
pressure 1)
10
Manual setting of DPS1 (clutch C1) initial
pressure 1)
9 (Manual setting of DPS3 (clutch C3) pre ---
filling time) 3)
8
(Manual setting of DPS2 (clutch C2) pre ---
filling time) 3)
7 (Manual setting of DPS1 (clutch C1) pre ---
filling time) 3)
6
Manual setting of R ---clutch initial pressure
1).
5 Manual setting of F ---clutch initial pressure
1).
4
Manual setting of R ---clutch pre ---filling ti-
me.
3 Manual setting of F ---clutch pre ---filling ti-
me.
2
Clutch pedal calibration.
1 Gas pedal calibration.
CAL START LEVEL
CAL 1 Automatic calibration of F ---direction (Y11).
CAL 2 Automatic calibration of R ---direction (Y12).
CAL 3 Automatic calibration of DPS clutch C1
(Y4).
CAL 4 Automatic calibration of DPS clutch C2
(Y6).
1. 8. 2000
1. 9. 2002
CAL 5 Automatic calibration of DPS clutch C3
(Y17) (not in use).
CAL 6 PTO automatic calibration
1) Before setting the initial pressures, the pre ---filling times
must be set.
2) Parameters are the same as codes for AD ---instrument, see
page 331/6.
3) Normally the pre ---filling indexes 7, 8 and 9 can be zero,
since their effect is minor due to the piston short free move-
ment.
B. Setting clutch pedal ratio index
Note! This setting procedure is only in AC 5.2. With this set-
ting the clutch pedal can be adjusted so that it engages exact
in the same point in forward and rearward direction. Increas-
ing the index one step increases all clutch pedal control va-
lues one percent and vice versa. I.e. when increasing the
index the clutch pedal engages deeper and vice versa. The
factory sets the indexes to 0. When both indexes are 0, the
clutch slips and engages little earlier when driving rearwards.
1. Activate the setting mode, see page 370/14. Step in the
menu with DPS push buttons and select either point 15 (ratio
index forwards) or 16 (rearwards).
2. When the selection has been done, press the DPS pre ---
programming button, after which the selected point is shown
without blinking and the valid and blinking ratio index can be
seen in the right.
3. The blinking index can be increased or decreased with the
DPS push buttons in the speed gear lever knob.
4. The index can be between ---5....+5. When there is a cor-
rect index value in the display, press the DPS pre ---program-
ming button. After a successful setting the correct index value
(without blinking) is shown in the display.
5. The setting mode can be left by switching off current.
6. Check the function of the clutch pedal by making startings
forwards and rearwards with slipping. Change the index
when necessary.
166
Model Code
371
6250-- 8950
FIII=setting
mode symbol
Module A=AC 5
E.g.
15=clutch pe-
dal ratio index
forwards.
Valid ratio in-
dex ---3.
Page
10