Fault Code Memory - Valtra 6000 Workshop Manual

37. Autocontrol 5.2 (K41107---)
Fault co- Control
de unit pin
d153 A1A2/3 In the reverse drive controls parking brake and one direction (F or R) active
A1A2/8 simultaniously. Rear shuttle lever switches probably in short circuit. This fault
A1A2/7 code appears only when the seat is turned backwards.
d215 A1A7/6 Front clutch pedal position > 50 % and d06 is active (d06=pedal limit switch
A1A5/7 S9). Check the limit switch and its adjustment.
d254 A1A2/6 Rear clutch pedal position > 50 % and d20 is active (d20=pedal limit switch
A1A7/1 S2W). Check the limit switch and its adjustment. This fault code appears only
when the seat is turned backwards.
Shuttle speed sensors (B12/B13) give different frequency. Difference
F320 A1A1/7
A1A1/5
over 30 %. One of the sensor possible faulty.
F321 A1A2/4 Engine rpm lower than what the shuttle sensors (B12/B13) indicate, when one sole-
noid is fully active. Engine rpm sensor B11 may be faulty.
F324 A1A1/7 Driving speed over 10 km/h and direction information in the control
A1A1/5
unit is changing. Shuttle sensors B12 or B13 may be faulti or wire
problems.
L419 A1A1/3 Full pressure has been connected to the PTO clutch over 3 seconds, but the PTO
shaft rotation speed is lower than it should be. PTO- - clutch may slip. It is possible that
the PTO rpm sensor B7 is faulty. Check in the test mode PTO lever switches S28 and
S29. Check that the switches have not been faulty connected (can be seen in the test
mode). Ensure that the PTO speed parameters P and L are correctly set.
L422 A1A1/7 One shuttle direction is engaged and full control has been active over 3 seconds.
A1A1/5
Shuttle rotation speed is lower than engine speed in relation to the DPS ratio. One
A1A2/4
multi- - disc clutch in the DPS or in the Shuttle can slip or one proportional valve
(Y4,Y6,Y17,Y11,Y12) can be trapped. This fault code also appears, if both shuttle
sensors (B12,B13) do not give a signal, when engine revs are over 1600 rpm (check
the fuse F22). This fault code is activated at engine speeds over 1000 rpm and in
HiTrol tractors at engine speeds over 1800 rpm. This fault code can also appear, if the
turbine clutch has too much slip (e.g. too little oil in the turbine clutch).
L334 A1A2/2 Driving speed over 65 km/h measured by gearbox speed sensor B6 frequen-
cy input. 4WD propeller shaft can be damaged.
L335 A1A2/4 Engine revs over 2800 rpm, measured by sensor B11 frequency input.
E. Fault code memory
The fault code memory functions in all tractors, which have
main program version 81 or later. In version 80 the fault code
memory has malfunctions.
For fault codes have been made a memory where can be
checked and removed appeared fault codes. The memory
stores three latest fault codes and their running hours (ac-
cording to the control unit hour counter "L ", not an exact
value).
The fault code memory FI can be activated in the same way
as the test mode FII, see page 370/8.
Number Mode
1

Fault code memory

(AC 5.2)
2 Test mode
3 Setting mode
When the fault code memory has been activated, the display
shows in the lower part of the display the fault codes stored
in the memory. The fault codes are visible in a correct order so
that after the activation there is an oldest code in the display.
Fault identification
(AC 5.2 only)
Mode symbol
F I
F II
F III
156
Model
1. 8. 2000
6250-- 8950
1. 9. 2002
This fault code is visible two seconds and after this is shown
the running hours of the code. The running hours are shown
also two seconds.
If there are many codes in the memory, a line is shown one
second between each codes. Then the next code and the run-
ning hours are shown. When all codes and running hours
have been shown, the first code appears again in the display.
The codes are shown until the current is switched off or the
DPS pre ---programming button is pressed over 4 seconds.
--- if there is no codes in the memory, the line is blinking in the
lower part of the display.
--- the fault code memory can be emptied by pressing the DPS
pre ---programming button over 4 seconds, after which the
codes disappear and the line starts to blink.
Code Page
371 6
Fault Tests Repairs,
functi- settings
on le-
vel
4
See table S t bl S See instr. i t
4
B on pa- B on pa-
ge 371/8. ge 371/8 ge ge
4
370/20.
3
See table See table
3
D on pa- See instr.
ge ge D on pa- D on pa-
1
371/9A
ge
370/22
2
See table See instr.
D on pa- D on pa-
ge ge
371/9A. 370/22.
See table
B on pa- See instr.
ge 371/8. B on pa-
ge
370/20.
4 See instr.
C on pa-
See table ge
E on pa- 370/21.
ge
371/9B.
See instr.
D on pa-
ge
370/22
1
1