Test Mode; Sprayer; Fertilizer; Drill - Valtra 6000 Workshop Manual

33. FieldMaster
C. Test mode
A test mode can be selected in the diplay. In this mode
there are shown signals from various sensors when they
are activated. The test mode can be selected in the display
in the same way as the language (see Page 3), but in place
of selection LANGUAGE must be selected TEST INPUT (or
test output). The test mode is individual for different imple-
ments, and it depends on sensors which have been fitted
on an implement in question.
The five first test points are the same for all implements,
and they indicate the function of the tractor sensors as fol-
lows:
RADAR: In this point are shown signals from the radar,
when driving slowly forwards.
PTO: Signals from the PTO sensor when the PTO shaft is
rotating.
WHEEL TRACTOR: Signals from the gearbox speed sen-
sor, when driving slowly forwards.
DIESEL: Not in use
IMPLEM: Signal when the lift/lower switch of the AC/
ACD ---power lift is turned to the transport position.
Note! TRAIL.1 ---TRAIL.7 in this mode mean correcponding
poles in the rear socket. TRAIL.8 is not in use.

1. Sprayer:

TEST INPUT
RADAR
0 HI
PTO
0 HI
WHEEL
TRACTOR
0 HI
DIESEL
0 HI
IMPLEM.
0 HI
TRAIL. 1
0 HI
TRAIL. 2
HI
TRAIL. 4
0 LO
TRAIL. 7
0 LO
TRAIL. 8
0 LO
BOMTEST
OK
TRAIL. 1: Signal from the pressure sensor. Low pressure
gives only few signals per second, higher pressure more.
TRAIL. 2: Signal from the flow meter. On turn of an impeller
gives two impulses.
TRAIL. 4: Signal from the wheel sensor of the sprayer
always when the magnet is at the sensor when driving
slowly forwards.
TRAIL. 7: Signal from the switch of the sprayer main valve
or from the sensor of the manual valve.
TRAIL. 8: not in use.
BOOM TEST: OK or ERROR.
1. 8. 1998

2. Fertilizer

TEST INPUT
RADAR
0 HI
PTO
0 HI
WHEEL
TRACTOR
0 HI
DIESEL
0 HI
IMPLEM.
0 HI
TRAIL. 1
0 HI
TRAIL. 2
HI
TRAIL. 4
0 LO
TRAIL. 7
0 LO
TRAIL. 8
0 LO
BOMTEST
OK
TRAIL. 1: Signal from a rpm sensor (RPM 1), when the
shaft equipped with the magnets is rotating.
TRAIL. 2: Not in use
TRAIL. 4: Signal from the implement wheel sensor, when
driving slowly forwards.
TRAIL. 7: not in use.
TRAIL. 8: not in use.
BOOM TEST: not in use.
OUT 1: Signal from FM into an actuator to close a hatch.
OUT 2: Signal from FM into an actuator to open the hatch
OUT 3: Not in use
OUT 4: Not in use
POT 1: Signal from an actuator (potentiometer), which
adjusts the position of the hatch. Lower number, when the
hatch is closed and upper number when the hatch is open.
POT 2: Not in use.

3. Drill

TEST INPUT
RADAR
0 HI
PTO
0 HI
WHEEL
TRACTOR
0 HI
DIESEL
0 HI
IMPLEM.
0 HI
TRAIL. 1
0 HI
TRAIL. 2
HI
TRAIL. 4
0 LO
TRAIL. 7
0 LO
TRAIL. 8
0 LO
BOMTEST
OK
344
Model Code
6200-- 8750 332
TEST OUTPUT
OUT 1
HI
OUT 2
HI
OUT 3
HI
OUT 4
0 HI
POT 1:
48
POT 2:
49
OUT 1
OUT 2
OUT 3
OUT 4
IMPLEM: Signal from the
switch or sensor of the lifting
arm, when the arm is raised.
TRAIL 1: Signal from the rpm
sensor on the sowing shaft,
when it is rotating.
TRAIL 2: Signal from the swit-
ches for the sowing shaft
speed control. When the
sowing shaft is rotating, HI is
visible. When the shaft does
not rotate, LO is visible. Can
also show signals from the
rpm sensor, when the shaft
equipped with magnets is
rotating.
TRAIL 4: Signal from the level
sensor in the tank, when the
tank is empty.
TRAIL 7: Signal from a switch
for remote control of the hatch
or from an implement sensor
when the implement is raised.
TRAIL 8: Not in use
BOOM TEST: Not in use.
Page
6