Toro MH-400SH2 Operator's Manual page 37

•
Setting and operating the floor alone
•
Setting and operating the option alone
•
Setting and operating both floor and option
together
Setting and Operating the Floor
Alone
Upon initially pressing the F
(when the floor is not running), the remote display
shows the stored setting and an S is displayed after
FLR (i.e. FLRS), indicating that the handheld remote
is in a set-only mode. In this set-only mode, you
can adjust the setting up or down, but the floor does
not activate, remaining off. This allows you to set a
desired floor speed or use the stored setting without
causing unwanted movement. After setting the speed,
press the F S
LOOR TART
the chosen setting (if you engage the hydraulics, the
floor starts). Press F
LOOR
the current value in memory.
Note:
Changes to the floor settings while the floor
is running are immediately effective, but they are
temporary unless you store the new setting by
pressing F S
LOOR TART
setting. For instance, you make an adjustment while
the display shows FLRS, press Floor Start starting
the floor at the adjusted setting, and then turn the
handheld remote off without pressing F
again, storing the change. The next time you use the
remote, the setting reverts to the previously stored
value.
Note:
A 10-second timer starts when you press
F S and FLRS (set-only mode) displays.
LOOR TART
If you do not press a button during the 10-second
interval, the display reverts to FLR and the previous
state/value displays and is enforced. The timer resets
to 10 seconds if you press any button while the
handheld remote is in the set-only.
1. Press the F
LOOR
The preview value and FLRS displays.
2. Adjust the speed setting using the I
F S button or the D
LOOR PEED
S button.
PEED
3. Press the F
LOOR
S button
LOOR TART
button to activate the floor at
S a third time to store
TART
again after changing the
LOOR
S button.
TART
NCREASE
F
ECREASE
or
S button to start the floor.
TART
4. Press the F
value.
The display shows FLOOR STORE. The set
value is used whenever the floor is started in the
future until you change the setting again.
Setting and Operating the Option
Alone
Upon initially pressing the O
(when the option is not running), the handheld
remote display shows the stored setting and an S is
displayed after OPT (i.e. OPTS), indicating that the
remote is in a set-only mode. In this set-only mode,
you can adjust the setting up or down, but the option
does not activate, remaining off. This allows you to
set a desired option speed or use the stored setting
without causing unwanted movement. After setting
the speed, press the O
the option at the chosen setting (if you engage the
S
TART
hydraulics , the option starts). Press O
third time to store the current value in memory.
Note:
Changes to the option settings while the
option is running are immediately effective, but they
are temporary unless you store the new setting by
pressing O
setting. For instance, you make an adjustment while
the display shows OPTS, press O
the option at the adjusted setting, and then turn the
handheld remote off without pressing O
again, storing the change. The next time you use the
remote, the setting reverts to the previously stored
value.
Note:
A 10-second timer starts when you press
O S
PTION TART
If you do not press a button during the 10-second
interval, the display reverts to FLR and the previous
state/value displays and is enforced. The timer resets
to 10 seconds if you press any button while the
LOOR
handheld remote is in the set-only.
1. Press the O
37
S button to store the floor
LOOR TART
PTION
S
PTION TART
S again after changing the
PTION TART
and FLRS (set-only mode) displays.
S button.
PTION TART
S button
TART
button to activate
S a
PTION TART
S starting
PTION TART
S
PTION TART