Vertical Position After Oversized Barcode (Bartop); Vertical Position After Oversized Character (Lcptop) - Tally Dascom 2810 User Manual

User Guide
User guide

Vertical position after oversized barcode (BarTop)

Vertical position after
This paramater controls the vertical position of characters with standard height
oversized barcode (BarTop)
which follow oversized characters.
This function is only effective in Genicom ANSI emulation.
If this option is disabled (Off), then the printer advances paper 1/8 inch when
exiting oversized characters. This characteristic is retained for compatibility with
older products.
If the option is enabled (On), then the current vertical position following the
printing of an oversized character will be the top of the oversized character cell. If
the next object on the page is located below this point, then the printer uses
vertical logic seeking to economize on paper movement.
Confirm the setting by pressing the Set key (1).
The Menu
The Menu

Vertical position after oversized character (LCPtop)

Vertical position after
Vertical position after
This paramater controls the vertical position of characters with standard height
oversized character
oversized character
which follow oversized characters.
(LCPtop)
(LCPtop)
This function is only effective in Genicom ANSI emulation.
If this option is disabled (Off), then the printer advances paper 1/8 inch when
exiting oversized characters. This characteristic is retained for compatibility with
older products.
Form feed mode (FFmode)
Form feed mode (FFmode)
FFmode PapOpt
FFmode PapOpt
Back Next
Back Next
This paramater controls the vertical position of characters with stan-
dard height which follow oversized characters.
This function is only effective in Genicom ANSI emulation.
Press BarTop (2) key.
Press BarTop (2) key.
Use the < (2) or > (3) key to select the desired setting.
Setting Options: Off/On
Default Setting: Off
Use the < (2) or > (3) key to select the desired setting.
Setting Options: Off/On
Default Setting: Off
If this option is disabled (Off), then the printer advances paper 1/8
inch when exiting oversized characters. This characteristic is re-
tained for compatibility with older products.
If the option is enabled (On), then the current vertical position follow-
ing the printing of an oversized character will be the top of the over-
sized character cell. If the next object on the page is located below
this point, then the printer uses vertical logic seeking to economize
This paramater controls the vertical position of characters with stan-
This paramater controls the vertical position of characters with stan- on paper movement.
dard height which follow oversized characters.
dard height which follow oversized characters.
Confirm the setting by pressing the Set key (1).
This function is only effective in Genicom ANSI emulation.
This function is only effective in Genicom ANSI emulation.
Press LCPtop (3) key.
Press LCPtop (3) key.
Press LCPtop (3) key.
Use the < (2) or > (3) key to select the desired setting.
Use the < (2) or > (3) key to select the desired setting.
Use the < (2) or > (3) key to select the desired setting.
Setting Options: Off/On
Setting Options: Off/On
Setting Options: Off/On
Default Setting: Off
Default Setting: Off
Default Setting: Off
If this option is disabled (Off), then the printer advances paper 1/8
If this option is disabled (Off), then the printer advances paper 1/8
inch when exiting oversized characters. This characteristic is re-
inch when exiting oversized characters. This characteristic is re-
tained for compatibility with older products.
tained for compatibility with older products.
If the option is enabled (On), then the current vertical position follow-
If the option is enabled (On), then the current vertical position follow-
ing the printing of an oversized character will be the top of the over-
ing the printing of an oversized character will be the top of the over-
sized character cell. If the next object on the page is located below
sized character cell. If the next object on the page is located below
this point, then the printer uses vertical logic seeking to economize
this point, then the printer uses vertical logic seeking to economize
on paper movement.
on paper movement.
Confirm the setting by pressing the Set key (1). Press the Next key
Confirm the setting by pressing the Set key (1). Press the Next key
(4) to access the next group of parameters.
(4) to access the next group of parameters.
Specifies whether a form feed is to be performed when the paper
Specifies whether a form feed is to be performed when the paper
reaches the top print line.
reaches the top print line.
Press FFmode (2) key.
Press FFmode (2) key.
Online
Online
The Menu
The Menu
User guide
User guide
67
87