Automatic Detection Of The Top Paper Margin (Aed) - Tally Dascom 2810 User Manual

User guide
User guide
User Guide
The measurement is made
▸ after power-on and before the first print job;
User guide Paperwidth Error
▸ after paper end and before the subsequent print job; after
Paperwidth Error
Press Online
Press Online
▸ changing the paper source (e.g. from Tractor 1 to Tractor 2).
3
1 2
1 2 3
When you submit a print job which exceeds the paper width, the following message appears in
the display:
Paperwidth Error
Press Online
1 2 3
If you press the Online key without having changed the paper, another line
is printed until reaching the measured paper-end position.
The sensor interprets dark areas with a width of 13 mm or more as the
right-hand paper edge.
If the sensor does not detect any black area, the maximum possible
printing width is used as the printable area.
If there is a sensor malfunction (e.g. because of dirt, a defect or
misinterpretation of the paper width) it is necessary to deactivate the APW
function (APW=Off), since otherwise the printout will be too narrow or there
will be no printout at all. In this case contact your service technician.
Confirm the setting by pressing the Set (1) key.

Automatic detection of the top paper margin (AED)

Automatic detection of the
Automatic detection of the
This menu option only appears, if a cut device is installed. It corrects possible
top paper margin (AED)
top paper margin (AED)
inaccuracies of the paper positioning at the cut edge if the paper path is changed
after a cutting action.
APW AED
APW AED
Back Next
Back Next
Automatic detection of the
top paper margin (AED) 1 2 3
1 2 3
APW AED
AED=Off
Back Next
AED=Off
Set < > Exit
Set < > Exit
1 2 3
1 2 3
1 2 3
AED=Off
Set < > Exit
1 2 3
When you submit a print job which exceeds the paper width, the fol-
When you submit a print job which exceeds the paper width, the fol-
lowing message appears in the display:
lowing message appears in the display:
Online
Online
4
When you submit a print job which exceeds the paper width, the fol-
4
Setup
Setup
lowing message appears in the display:
The print job is stopped at the measured paper-end position
The print job is stopped at the measured paper-end position after
The print job is stopped at the measured paper-end position after
after printing the first line.
Online printing the first line.
printing the first line.
4 You can now either cancel the print job or load suitable paper. In the
You can now either cancel the print job or load suitable
You can now either cancel the print job or load suitable paper. In the
Setup
latter case, the printer will resume the print job upon pressing the
paper. In the latter case, the printer will resume the print job
latter case, the printer will resume the print job upon pressing the
Online key.
upon pressing the Online key.
Online key.
The print job is stopped at the measured paper-end position after If you press the Online key without having changed the paper,
If you press the Online key without having changed the paper,
another line is printed until reaching the measured paper-end printing the first line.
another line is printed until reaching the measured paper-end
position.
position.
You can now either cancel the print job or load suitable paper. In the
latter case, the printer will resume the print job upon pressing the
The sensor interprets dark areas with a width of 13 mm or
The sensor interprets dark areas with a width of 13 mm or
Online key.
more as the right-hand paper edge.
more as the right-hand paper edge.
If the sensor does not detect any black area, the maximum
If you press the Online key without having changed the paper,
If the sensor does not detect any black area, the maximum
possible printing width is used as the printable area.
another line is printed until reaching the measured paper-end
possible printing width is used as the printable area.
position.
If there is a sensor malfunction (e.g. because of dirt, a defect
If there is a sensor malfunction (e.g. because of dirt, a defect
STOP
or misinterpretation of the paper width) it is necessary to
STOP
The sensor interprets dark areas with a width of 13 mm or
or misinterpretation of the paper width) it is necessary to
deactivate the APW function (APW=Off), since otherwise the
more as the right-hand paper edge.
deactivate the APW function (APW=Off), since otherwise the
printout will be too narrow or there will be no printout at all. In
If the sensor does not detect any black area, the maximum
printout will be too narrow or there will be no printout at all. In
this case contact your service technician.
possible printing width is used as the printable area.
this case contact your service technician.
Confirm the setting by pressing the Set (1) key.
If there is a sensor malfunction (e.g. because of dirt, a defect Confirm the setting by pressing the Set (1) key.
STOP
or misinterpretation of the paper width) it is necessary to
deactivate the APW function (APW=Off), since otherwise the
This menu option only appears, if a cut device is installed. It corrects
This menu option only appears, if a cut device is installed. It corrects
printout will be too narrow or there will be no printout at all. In
possible inaccuracies of the paper positioning at the cut edge if the
possible inaccuracies of the paper positioning at the cut edge if the
this case contact your service technician.
paper path is changed after a cutting action.
paper path is changed after a cutting action.
Confirm the setting by pressing the Set (1) key.
Select the AED (3) menu.
Select the AED (3) menu.
Select the AED (3) menu.
Online
Online
This menu option only appears, if a cut device is installed. It corrects
4
possible inaccuracies of the paper positioning at the cut edge if the
4
Setup
Setup
paper path is changed after a cutting action.
Select the AED (3) menu.
Setting options: On/Off
Setting options: On/Off
Setting options: On/Off
*
Default setting:
Online
*
Default setting:
Online
Default setting: Off
Online
Confirm the setting by pressing the Set (1) key. Change to the next
4
Confirm the setting by pressing the Set (1) key. Change to the next
Setup
4 Confirm the setting by pressing the Set (1) key. Change to
parameter group with the Next key (4).
4
Setup
parameter group with the Next key (4).
Setup
the next parameter group with the Next key (4).
Setting options: On/Off
*
Default setting:
Online
Confirm the setting by pressing the Set (1) key. Change to the next
4
parameter group with the Next key (4).
Setup
Off
Off
Off
Advanced menu
Advanced menu
Advanced menu
Advanced menu
111
111
89
111