Specifications; Electrical Data, 380-480 - Danfoss VLT AutomationDrive FC 361 Series Design Manual

Specifications

5 Specifications
5.1 Electrical Data, 380-480 V
®
VLT AutomationDrive FC 361
High/normal overload
(High overload=150% current during 60 s, normal
overload=110% current during 60 s)
Typical shaft output at 400 V [kW]
Typical shaft output at 460 V [hp]
5 5
Enclosure size
Output current (3-phase)
Continuous (at 400 V) [A]
Intermittent (60 s overload) (at 400 V) [A]
Continuous (at 460 V) [A]
Intermittent (60 s overload) (at 460 V) [kVA]
Continuous kVA (at 400 V) [kVA]
Continuous kVA (at 460 V) [kVA]
Maximum input current
Continuous (at 400 V) [A]
Continuous (at 460 V) [A]
Maximum number and size of cables per phase
Mains and motor [mm
Maximum external mains fuses [A]
Estimated power loss at 400 V [W]
Estimated power loss at 460 V [W]
3)
Efficiency
Output frequency [Hz]
Heat sink overtemperature trip [°C (°F)]
Weight, enclosure protection rating IP20 kg (lbs)
Efficiency 3)
Output frequency [Hz]
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
Table 5.1 Electrical Data for Enclosures J8, Mains Supply 3x380–480 V AC
1) For fuse ratings, see chapter 7.5 Fuses and Circuit Breakers.
2) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to
dimensioning of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control
card power consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-
efficiency-directive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for
slots A and B each add only 4 W.
3) Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy
efficiency class, see chapter 5.4 Ambient Conditions. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
16
VLT® AutomationDrive FC 361
2 (AWG)]
1)
2), 3)
2), 3)
Danfoss A/S © 03/2019 All rights reserved.
N90K N110
NO HO NO
90 90 110
125 125 150
177 177 212
195 266 233
160 160 190
176 240 209
123 123 147
127 127 151
171 171 204
154 154 183
2x95 (2x3/0)
315 315
2031 2031 2559
1828 1828 2261
± 15% (tolerance relates to variety in voltage and cable conditions). These
N132 N160
HO NO HO
110 132 132
150 200 200
J8
212 260 260
318 286 390
190 240 240
285 264 360
147 180 180
151 191 191
204 251 251
183 231 231
350 400
2289 2954 2923
2051 2724 2089
0.98
0–590
110 (230)
98 (216)
0.98
0–590
110 (230)
75 (167)
NO
160
250
315
347
302
332
218
241
304
291
3770
3628
MG06K102