Page 1
Te c hn i cal Re fe re nce 020-101697-05 Boxer 4K Serial API Commands...
Page 2
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
Once you have connected your computer to either the RS232 IN port (depending on which standard is supported by your computer) or to the Ethernet port on Boxer 4K, you can remotely access controls and image setups, issue commands or queries, and receive replies.
Ethernet is setup to obtain an IP address automatically if a DHCP server is on the network. To modify IP settings, or manually enter an address. Christie recommends using the Ethernet port on the IMXB as the HDBaseT port is limited to 100 Mb/s. You cannot change the IP settings using the web interface.
(+) character to separate the code and subcode. If there is no subcode, the plus sign (+) is also omitted. In messages sent to Boxer 4K that have a subcode, a space between the subcode and the first parameter (or special character) is optional.
Data The value for a given Boxer 4K state, such as on or off, appears in ASCII-decimal format directly after the request/reply symbol. You can add an optional space after the symbol—such as before the data—in a set message, but data in replies follow the...
The acknowledgment is returned after the message has been received and fully executed by Boxer 4K (such as in the case of a source switch it is not sent until the switch is complete). If the message cannot be executed for some reason (such as invalid parameters, time-out, and so on) a NAK is returned instead (not-acknowledge).
= F0h when only the low byte is used = 240 Boxer 4K collects all of the message bytes as defined in the first byte of the message, then creates its own checksum value for comparison with the checksum included in the controller’s message.
Normally messages can be sent to the projector before processing of earlier messages is complete— Boxer 4K stores messages in a buffer until ready to process. However, if a series of messages is sent, Boxer 4K may not be able to process them as fast as they arrive and the buffer becomes full.
Serial API commands The Boxer 4K commands can be used to modify product settings. ADR–Projector Address Sets or queries the device address. This command also helps to identify where a response or asynchronous message originates from. Generally, this command is used for projectors that are daisy-chained together using the RS232 style communication.
Serial API commands Result: (GAM 2600) BST–Built-in Self Test Performs self-checks in Boxer 4K that can be safely executed either in standby, on, or cool down mode. Do not execute this command while Boxer 4K is warming up. Commands Command...
(Saved value) DEF–Factory Defaults Resets Boxer 4K to its factory default values. Note the following about this command: • Performing this command while the power is on does not reset the Lamp Selection value while in limited mode.
Configures which EDID is presented using inputs that support EDIDs (such as DisplayPort, HDMI, DVI, and so on). Use this command to configure what Boxer 4K advertises regarding the type of signals it accepts. This command does not need to be set to accept a particular type of signal.
Controls or monitors the state of the general purpose inputs and outputs. The pins reserved for 12V and ground cannot be read, set, or configured. For a mapping of the IO pins to the physical connector pins, refer to the Boxer 4K User Manual (P/N: 020-101777-XX). Commands...
NET+MAC0? Returns the MAC address of the Ethernet port. (Read- — only) NET+PORT? Returns the TCP port used for the Christie serial 1024 to 49151 (with protocol over Ethernet. (Read-only) some exceptions) Boxer 4K Serial API Commands Technical Reference 020-101697-05 Rev. 1 (07-2017) Copyright 2017 Christie Digital Systems USA Inc.
Displays values and fault conditions related to cooling and fans. Serial (SST+SERI?) Displays values and fault conditions related to hardware serial numbers. For more information about the status groups, items, and theirs state, see the Boxer 4K Status System Guide (P/N: 020-101695-XX). Commands...