Summary of Contents for Christie Inspire 4K Series
Page 1
Installation and Setup Guide 020-002097-01 Inspire Series 4K...
Page 2
Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
Read all safety and warning guidelines before installing or operating the projector. This projector must be operated in an environment that meets the operating range specification. Use only the attachments and/or accessories recommended by Christie. Use of others may result in the risk of fire, shock, or personal injury.
Caution! If not avoided, the following could result in minor or moderate injury. • ELECTRICAL and BURN HAZARD! Use caution when accessing internal components. • Only Christie qualified technicians are authorized to use the tools provided in the toolbox. Laser safety precautions This product is classified as Class 1 Laser Product-Risk Group 2 according to IEC 60825-1:2014, EN 60825-1:2014+A11:2021 complies with FDA regulations 21 CFR 1040.10 and 1040.11 as a Risk...
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.
2019 5 8 1:2014 and IEC 62471-5:2015. Mount above the heads of children. Christie recommends using a ceiling mount to place the product above eye-level for children. Make sure to adjust the feet of the top projector before stacking to avoid damage to the lower projector.
Introduction Contact your dealer Record the information about your projector and keep this information with your records to assist with the servicing of your projector. If you encounter a problem with your Christie projector, contact your dealer. Purchase record Dealer:...
Product documentation For installation, setup, and user information, see the product documentation available on the Christie Digital Systems USA Inc. website at www.christiedigital.com. Read all instructions before using or servicing this product. 1. Access the documentation from the Christie website: •...
Christie recommends a 20 A rated wall breaker for the installation. To ensure safe operation, only use the AC power cord provided with the product or recommended by Christie. See Connecting to AC power on page 22 for further information on the power requirements.
Throw Ratios Technical Reference (P/N: 020-103497-XX). • 360 degree free orientation operation When installing the projector in portrait orientation, Christie recommends the built in keypad and power inputs face upwards. This allows access to the built in keypad and power connections during operation.
2. To use a third party ceiling mount kit, ensure the screws used to attach a mount to the projector meet the following specifications: • Screw type: 35 mm for Christie One Mount (P/N: 108-506102-XX) Lens 480.00 486.00(WITH ID RIB) M4(4X) 240.00...
3. Remove the filter from its compartment. 4. Clean or replace the filter. In environments where dust, dirt, and other contaminants are higher than normal, Christie recommends replacing the air filter more frequently than 500 hours as specified in the current maintenance schedule.
Installation and setup To ensure safe operation, only use the AC power cord provided with the product or recommended by Christie. Connect the AC power cord to the AC inlet on the projector. Turning on the projector The projector cables must be securely connected before turning the power on.
3. Connect the plug of the power cable to the projector. 4. Turn on the device. 5. If steps 1 to 4 did not lead to the required result, contact Christie Technical Support or an authorized Christie service center. LED status indicator LED status indicator helps identify the projector state.
Calculating the lens offset Adjust the lens offset (shift) to align the image on the screen with half image size. To ensure optimal projector and lens performance, Christie recommends keeping the offset (shift) values within the ranges specified below. •...
Page 46
Corporate of ces Christie Digital Systems USA, Inc. Cypress ph: 714 236 8610 Christie Digital Systems Canada Inc. Kitchener ph: 519 744 8005 Mexico ph: +52 55 4744 1790 United States (Arizona) ph: 602 943 5700 United States (New York) ph: 646 779 2014 For the most current technical documentation, visit www.christiedigital.com.