Page 1
User Guide 020-102958-05 4K40-RGB D4K40-RGB, Roadie 4K40-RGB...
Page 2
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
This projector is intended for use in a non-cinema environment. This projector must be operated in an environment that meets the operating range specification. Use only the attachments and/or accessories recommended by Christie. Use of others may result in the risk of fire, shock, or personal injury.
Possible hazardous optical radiation emitted from this product. (Risk group 3) • Only Christie qualified technicians who are knowledgeable about the hazards associated with laser use, high-voltage, and high temperatures generated by the product are authorized to assemble, install, and service the Christie Laser Projection System.
Page 11
• Temporary show installations containing Risk Group 3 laser-illuminated projectors may be installed by Christie or sold or leased only to valid laser light show variance holders (laser light show manufacturers) for image projection applications. Such manufacturers may currently hold a valid variance for production of Class IIIb and IV laser light shows and/or for incorporation of the Risk Group 3 laser-illuminated projectors into their shows.
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.
Indicates Class 4 laser radiation when open. Avoid eye or skin exposure to direct or scattered radiation. Product documentation For installation, setup, and user information, see the product documentation available on the Christie website. Read all instructions before using or servicing this product. D4K40-RGB and Roadie 4K40-RGB 1.
Contact your dealer Record the information about your projector and keep this information with your records to assist with the servicing of your projector. If you encounter a problem with your Christie projector, contact your dealer. Purchase record...
Adjusting the image Adjust the projector image. Christie recommends warming the lens before completing these procedures as focus may change as the lens warms. Selecting screen image orientation Specify the orientation to use for the image. The projector supports front projection, rear projection, front projection inverted, or rear projection inverted.
Signal color correction Adjust the video signal color as required. For best results, Christie recommends setting all color and gamma settings to Auto Detect. Adjusting the color space Determine how the color components are decoded for accurate color in the display.
1. Create an edge blend file using the Christie or application. To connect 4K40-RGB with Christie or , use port 3003. Christie Twist Premium, Twist Pro, and offer advanced warping options. Refer to the Christie website (www.christiedigital.com) for product information and documentation.
1. Create a warp file using the Christie or application. To connect 4K40-RGB with or , use port 3003. Christie Twist Premium, Twist Pro, and offer advanced warping options. Refer to the Christie website (www.christiedigital.com) for product information and documentation.
2. To disable the secondary receivers, select Enter. Informing the source of signal preferences Configure 4K40-RGB to automatically inform the video source of the preferred signal formats. 1. If you need a specific frame rate, from the display panel, select MENU > Configuration >...
™ version To ensure color and brightness are held at the required levels for your installation, Christie recommends enabling LiteLOC version 2.0 for each laser configuration you create. When you set the required brightness, LiteLOC 2.0 maintains color and only decreases brightness if the system requires When LiteLOC 2.0 is enabled, the projector issues a warning when the brightness target is decreased...
1. Ensure the projector is running in representative ambient light. 2. Setup a spectroradiometer, such as the CR-250, on a tripod. If not using the CR-250 or better, Christie recommends placing the meter perpendicular to the screen to achieve accurate measurements.
There are 512 channels per universe. 4K40-RGB specifies 24 channels. 4K40-RGB has multiple methods of being controlled in addition to Art-Net. If a setting is changed through another interface, the DMX controller can re-assert control by changing the value on the appropriate DMX channel.
Not all options listed in the table are available on all products. Available options depend on the projector model and the cards installed on the projector. The QSFP+ options require the Enable Christie Link option to be set.
QSFP+ [2-2] Working with macros Automate tasks in 4K40-RGB with macros so the same tasks can be done on a regular basis. If the date and/or time is changed on the projector, a macro may be unexpectedly executed. Adding a Scheduled Event macro Create a Scheduled Event macro to automate a repetitive task.
An input pin can only have a maximum of two events, one for each transition type. 7. In the Serial Command field, enter the serial command(s) you want to run. For available serial commands and their syntax, refer to the 4K40-RGB Serial Commands Guide (P/N: 020-102972-XX).
(SST+CONF?1) serial API command. Christie Technical Support will send a zipped license file to you. If you sent more than one serial number, you will receive multiple license files as the .key file is based on the serial number of the projector.
10. Repeat steps 3 to 9 for each additional projector. Exporting backup settings to an external device Save the 4K40-RGB settings to a USB flash drive (projector) or file (web interface). 1. If using the display panel to export settings, insert a USB flash drive (properly formatted as FAT) into the USB port on 4K40-RGB.
Follow these procedures to help with diagnosing issues with 4K40-RGB. Viewing 4K40-RGB information View the licenses for the software added to 4K40-RGB and the licenses of the software used to operate 4K40-RGB. The information is read-only. 1. To view the additional software added to 4K40-RGB, select MENU > Admin > Licenses.
2. Scroll to the status category you want to view and select it. Running the 4K40-RGB interrogator The interrogator captures diagnostic information Christie personnel uses to help diagnose and correct any issues. 1. Insert a USB flash drive in the USB port on 4K40-RGB.
3. To confirm your selection, select Enter. Configuring traps A trap is a condition that SNMP monitors on 4K40-RGB. 1. Select MENU > Communications > SNMP > Trap Configuration. 2. Select the trap you want to enable and select Enter.
Page 62
Corporate offi ces Worldwide offi ces Christie Digital Systems USA, Inc. Africa United Kingdom Columbia Korea (Seoul) ph: 714 236 8610 ph: +27 (0)11 510 0094 ph: +44 (0) 118 977 8000 ph: +57 (318) 447 3179 ph: +82 2 702 1601 Christie Digital Systems Canada Inc.