Yaesu FT-100D Operating Manual page 103

CAT System Programming
Note 4: Read Meter
+0
-+
MSW1 (Microphone Switch 1): COh
=
ACC, 90h
=
UP, 60h
=
DOWN, 30h
=
PTT
+1
-+
FWD (Tx Forward Power): OOh - FFh
+2
-+
REV (Tx Reverse Power): OOh - FFh
+3
-+
S (S-meter Level): OOh - FFh
+4
-+
MIC (Microphone Level): OOh - FFh
+5
-+
NOISE (Squelch Level) : OOh - FFh
+6
-+
MSW2 (Microphone Switch 2): 90h
=
P2, 60h
=
P1, 30h
=
P
+7 -+ TEMP (Final Transistor Temperature): OOh - FFh
+8
-+
ALe (ALC Level): OOh - FFh
Note 5: Read Status Flags
+0 Status 0
Status 0
+1 Status 1
Bit
a
-+
SPLIT 1
=
on,
a
=
off
1
-+
Not Used
+2 Status 2
+3 Status 3
2
-+
TUNE 1
=
activate,
a
=
wait
3
-+
CAT IN: 1
=
on,
a
=
off
4
-+
Not Used
Status 1:
Bit
a
-+
Not Used
1
-+
MR CHK: 1 = on,
a
=
off
2
-+
B VFO: 1
=
VFO B on,
a
=
VFO B off
3
-+
OMB: 1 = on,
a
=
off
4
-+
M TUNE: 1 = on, 0
=
off
+4 Status 4
5
-+
POWER: 1
=
on.
a
= off
6
-+
MUTE 1
=
on,
a
= off
5
-+
VFO: 1
=
VFO Mode.
a =
other Mode (such as OMB Mode)
+5 Status 5
+6 Status 6
7
-+
TX N 1
=
on (Tx),
a
=
off (Rx)
6
-+
MEM: 1
=
Memory Mode,
a
=
other Mode (such as VFO Mode)
7
-+
SRCH: 1
=
Smart Search on,
a =
Smart Search off
+7 Status 7
Status 2:
Bit
a
-+
FAST. 1
=
on.
a
=
off
1
-+
TUNER: 1
=
on.
a
=
off
2
-+
BKMR: 1
=
Vacant Memory Channels are skipped when recalling the Memory Channel
o
=
All Memory Channel recalled when recalling the Memory Channel
3
-+
LOCK 1
=
Main Dial lock on,
a
=
Main Dial lock off
4
-+
SOLSC: 1
=
on.
a
=
off
5
-+
UPSCN: 1
=
Up Scan,
a
= Down Scan
6
-+
MEM 1
=
Memory Mode,
a
=
other Mode (such as VFO Mode)
7
-+
SRCH 1
=
Smart Search on,
a
=
Smart Search off
Status 3:
Bit a
-+
1 MHz' 1
=
1 MHz Up/Down on, a
=
1 MHz Up/Down off
1
-+
1a MHz: 1
=
1a MHz Up/Down on. a = 1a MHz Up/Down off
2
-+
FMLOC: 1
=
FM auto lock on,
a
=
FM auto lock off
3
-+
Not Used
4
-+
CATIX 1
=
Tx on CAT command.
a
=
Rx on CAT command
5
-+
NOTX. 1
=
Tx Inhibit on,
a
=
Tx Inhibit off
6
-+
KEYUP: 1
=
Key is up,
o
=
Key is pressed
7
-+
PTIWA: 1
=
PTI waiting on.
a
=
PTI waiting off
Status 4:
Bit
a
-+
Not Used
1
-+
DSPBP: 1
=
DSP BPF on.
a
=
DSP BPF off
2
-+
DSPNT 1
=
DSP NOTCH on, 0
=
DSP NOTCH off
3
-+
DSPNR: 1
=
DSP Noise Reducer on.
a
=
DSP Noise Reducer off
4
-+
ALOCK: 1
=
Panel Lock on.
a
=
Panel Lock off
5
-+
GROUP: 1
=
Memory Channel Group on.
a
=
Memory Channel Group off
6
-+
PRGM 1
=
PMS on,
a
=
PMS off
7
-+
Not Used
Status 6
Bit
a -+
DULON 1
=
Dual Watch Operation on,
a
=
Dual Watch Operation off
1
-+
DULCK: 1
=
Dual Watch is Checking.
a
= Not checking
2
-+
Not Used
3
-+
BUSY 1
=
BUSY on.
a
=
BUSY off
4
-+
Not Used
Status 5:
Bit
a
-+
ARTS 1
=
ARTS on,
a
=
ARTS off
1
-+
BKIN: 1
=
CW Break-in on. a = CW Break-in off
2
-+
KEYER: 1
=
CW Keyer on,
a
= CW Keyer off
3
-+
AUTIX 1
=
DSP Noise Reducer on,
o
=
DSP Noise Reducer off
4
-+
Not Used
5
-+
Not Used
6
-+
WAIT 1 = Antena Tuner Waiting,
a
=
Antenna Tuner Activate
7
-+
HI SWR: 1
=
HI SWR on.
a
=
HIGH SWR off
Status 7:
Bit 0
-+
SIDE 1
=
CW S,detone on, 0
=
CW S,detone off
1
-+
MUFST. 1
=
Menu Fast on.
a
= Menu Fast off
2
-+
Not Used
3
-+
Not Used
4
-+
Not Used
5
-+
PROC. 1
=
AF Speech Processor on,
a
=
AF Speech Processor off 5
-+
AGCSL: 1
=
AGC Slow,
a
=
other state (such as AGC Auto)
6
-+
AGCFS: 1 = AGC Fast.
a
=
other state (such as AGC Slow)
7
-+
MTMOD: 1
=
SWR Meter,
a
=
ALC Meter
6
-+
NBON 1
=
Noise Blanker on.
a
=
Noise Blanker off
7
-+
VOXON: 1
=
VOX on. 0
=
VOX off
FT-100
MICRO MOBILE OPERATING MANUAL
101