Programming The Gsm Intercom - Videx 4000 Series Technical Manual

4000 Series GSM Audio Intercom with Proximity

Programming the GSM Intercom

PROGRAMMING THE GSM INTERCOM
Programming the GSM PRO intercom can be carried out in two ways, either by sending text (SMS) messages or by using the GSMSK
PC software (ver 4.0.0.0 or later), also refer to the programming manual GSMSK_66251720_EN_V2-0 (or later).
IMPORTANT NOTE: When you are required to use " in a text message it is very important to use the correct symbol and not for
example ' (or two ' single apostrophes side by side which you will see look the same but will be interpreted differently by the
GSM PRO intercom panel).
PROGRAMMING BY TEXT MESSAGE
Programming by text message is a simple way to customise the settings of the GSM PRO intercom panel and add or delete telephone
numbers. If you have a large number of buttons or telephone numbers to enter you may find programming easier with the GSMSK
PC software. Simply send texts in the following format shown below to the telephone number of the SIM within the GSM PRO
intercom panel:
<4 DIGIT CODE> <3 DIGIT FUNCTION CODE> <OPTIONAL DATA> <OPTIONAL ?>
4 DIGIT CODE
3 DIGIT FUNCTION CODE
DESCRIPTION
Store a primary telephone no.
Store divert 1 telephone no.
Store divert 2 telephone no.
Store divert 3 telephone no.
Store a primary telephone no.
and divert no's in a single text
message
Store a dial to open no. (DTO)
or
Store up to 5 dial to open no's
(DTO) in a single text message to
the next available locations
Delete a dial to open no. without
knowing it's location
Set call time
Set relay time
Set auxiliary AO1 output time
Set auxiliary AO1 out mode
Set auxiliary AO2 output time
Keep connection facility
Divert to next no. time
Check GSM signal strength
Check software version
Dial a number
Store SMS message for g-4
Change 4 digit code
Trigger the relay
Trigger the auxiliary output AO1 A1O
Trigger the auxiliary output AO2 A2O
Store balance check dial string
Check credit balance
4000 Series GSM Audio Intercom - Technical Manual
This code prevents unauthorised access to the programmable features of the system. The code must
be four digits long but can be any combination using digits 0 – 9. The default code is 1111 and will
be used for all examples in this manual.
The 3 digit function code identifies the programmable feature to be changed. The code must be in
capital letters. The following table lists the available codes.
CODE EXAMPLE
STN 1111STNnnn"01912243174"
STD
1111STDnnn"01912241559"
STE 1111STEnnn"01912243678"
STF
1111STFnnn"01912245326"
STN 1111STNnnn"pn", " d1", " d2", " d3"
1111STNnnn"01912243174",
"01912241559", " 01912243678",
"01912245326"
STR 1111STRnnn"07771234567"
1111STR"n1", " n2", " n3", " n4", " n5"
1111STR"01912243174",
"01912241559", " 01912243678",
"01912245326", " 07897123456"
DET 1111DET"01912243174"
SPT 1111SPTnn
RLT 1111RLTnn
A1T 1111A1Tnn
A1M
1111A1Mnn
A2T 1111A2Tnn
NOD
1111NODnn
DIT 1111DITnn
SIG 1111SIG?
VER
1111VER?
DLE 1111DLE"123"
SMS
1111SMS"HouseAlarm"
CDE 1111CDE1234
RLY 1111RLY
1111A1O
1111A2O
SDL
1111SDL"*#1345#"
BAL 1111BAL?
SETTINGS
nnn = 001 - 050
nnn = 001 - 050
nnn = 001 - 050
nnn = 001 - 050
nnn = 001 - 050
pn = primary no.
d1 = divert 1 no.
d2 = divert 2 no.
d3 = divert 3 no.
nnn = 000 - 999 or
nnn = optional
n1 = 1st DTO
n2 = 2nd DTO
n3 = 3rd DTO
n4 = 4th DTO
n5 = 5th DTO
n/a
nn = 01 - 12
nn = 00 - 99
nn = 00 - 99
nn = 00 - 05
nn = 00 - 99
nn = 01 - 99
nn = 01 - 99
n/a
n/a
n/a
n/a
Any 4 digits
n/a
n/a
n/a
n/a
n/a
- 37 -
DEFAULT PAGE
n/a 39 - 40
n/a 39 - 40
n/a 39 - 40
n/a 39 - 40
n/a 40
n/a 41 - 42
n/a 42
02 (40s) 42 - 43
05 (5s) 43
05 (5s) 43
01 43
05 (5s) 44
0 (disabled) 44
15 (15s) 44
n/a 44
n/a 44
n/a 44 - 45
AUX TRIG 45
1111 45
n/a 45
n/a 45
n/a 45
n/a 45
n/a 45 - 46
66250754-EN - V1.0 - 18/02/19