Videx 4000 Series Technical Manual page 44

4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
SET AUXILIARY OUTPUT AO2 TIME (A2T)
The auxiliary output AO2 time can be set from 01 - 99 seconds or latching (set the AO2 output time to 00 for latched mode. In latch
mode the AO2 output will stay triggered until the relevant command is sent again to unlatch the AO2 output).
1111A2Tnn
1111A2Tnn?
1111A2T?
SET DAYS TO WAIT BEFORE MAKING A CALL (NOD)
In the event the GSM PRO intercom panel is not used for long periods of time it could be possible that the network disconnects it. To
prevent this from happening it is possible to program a time period (from 01 – 99 days or disabled 00) to wait before the intercom
panel makes a short call to refresh the connection to the network. This time period is reset after each call made on the system and
will only happen if the full time period elapses without any incoming or outgoing calls.
1111NODnn
1111NODnn?
1111NOD?
DIVERT TIME (DIT)
The divert time is the number of seconds to wait for a call to be answered before diverting to the 2nd, 3rd and 4th number. The
default time is 15 seconds (the count down begins from when the call button is pressed, but is refreshed when the telephone
begins to ring) and can be set from 01 – 99 seconds.
1111DITnn
1111DITnn?
1111DIT?
CHECK SIGNAL STRENGTH (SIG)
At any time the signal strength of the GSM PRO can be checked (also see notes on understanding the signal strength on page XX).
It is advisable that when the GSM PRO is first setup and before any other programming is carried out to check the signal strength
of the GSM PRO intercom. If the signal strength is too low the GSM PRO intercom may not operate properly and therefore the GSM
antenna will need to be repositioned to increase the signal strength. Use the following command to check the signal strength.
1111SIG?
CHECK SOFTWARE VERSION (VER)
It is possible to check the current version of software on the GSM PRO intercom. This may be necessary to see if an update is required
for any additional features or updates on the GSM PRO intercom which may be included on later versions. Use the following
command to check the software version.
1111VER?
FORCED DIAL/DIAL A NUMBER (DLE)
A useful feature of the GSM PRO intercom is its ability to call a number sent to it in a text message. This feature can be used when
setting up the SIM card. For example, disabling the voicemail facility or disabling automatic SMS messages or missed calls. Any
number up to 15 digits can be called and the call will last for a maximum of 40 seconds. The example below would switch off
voicemail on a Vodafone SIM card. Substitute the Vodafone number for other service providers.
1111DLE"1210"
Other useful numbers which can be used with this feature are as follows. Please also check the network service provider's web sites
for other useful codes.
DISABLE VOICEMAIL
DISABLE TEXT ALERTS
4000 Series GSM Audio Intercom - Technical Manual
Store the AO2 time nn = time in seconds (e.g. nn = 05, time = 5 seconds).
Store the AO2 time nn = time in seconds. Also send a confirmation text back to the sender.
Query the current stored AO2 time. A text message will be sent back to the sender showing
the stored AO2 time.
Store the time nn = time in days (e.g. nn = 07, time = 7 days).
Store the time nn = time in days. Also send a confirmation text back to the sender.
Query the current stored time. A text message will be sent back to the sender showing
the stored time.
Store the divert time nn = time in seconds (e.g. nn = 15, time = 15 seconds).
Store the divert time nn = time in seconds. Also send a confirmation text back to the
sender.
Query the current stored divert time. A text message will be sent back to the sender
showing the stored divert time.
Check the signal strength of the GSM PRO intercom and send a confirmation text back to
the sender.
Check the software version of the GSM PRO intercom and send a confirmation text back
to the sender.
Dial 1210 for the intercom panel.
Vodafone
1210
#148#
- 44 -
O
2
1760
1760
66250754-EN - V1.0 - 18/02/19