Programming The Gsm Intercom - Videx VR4KGSM-1 Technical Manual

4000 Series Vandal Resistant GSM Audio Intercom with Proximity Facility

Programming the GSM Intercom

PROGRAMMING THE GSM INTERCOM
Programming the GSM intercom can be carried out in two ways, either by sending text (SMS) messages or by using the GSMSK PC
software (ver 3.1.0.10 or later), also refer to the programming manual GSMSK-66251720-EN-V1-3 (or later).
IMPORTANT NOTE: When you are required to use " in a text message it is very important to use the correct symbol and not for
example ' (or two ' single apostrophes side by side which you will see look the same but will be interpreted differently by the
GSM intercom panel).
PROGRAMMING BY TEXT MESSAGE
Programming by text message is a simple way to customise the settings of the GSM intercom panel and add or delete telephone
numbers. If you have a large number of buttons or telephone numbers to enter you may find programming easier with the GSMSK
PC software. Simply send texts in the following format shown below to the telephone number of the SIM within the GSM intercom
panel:
<4 DIGIT CODE> <3 DIGIT FUNCTION CODE> <OPTIONAL DATA> <OPTIONAL ?>
4 DIGIT CODE
3 DIGIT FUNCTION CODE
DESCRIPTION
Store a primary telephone no.
Store divert 1 telephone no.
Store divert 2 telephone no.
Store divert 3 telephone no.
Store dial to open no.
Set call time
Set relay time
Set auxiliary AO output time
Set auxiliary AO out mode
Keep connection facility
Divert to next no. time
Check GSM signal strength
Check software version
Dial a number
Change 4 digit code
Trigger the relay
Trigger the auxiliary output AO
Store balance check dial string
Check credit balance
Store master telephone no.
Latch the relay
Unlatch the relay
Latch the auxiliary AO output
Unlatch the auxiliary AO output
Store time band
Check/Set date & time
Silent dialling mode
Send tone after answer (But 1)
Send tone after answer (Div 1)
4000 Series Vandal Resistant GSM - Technical Manual
This code prevents unauthorised access to the programmable features of the system. The code
must be four digits long but can be any combination using digits 0 – 9. The default code is 1111
and will be used for all examples in this manual.
The 3 digit function code identifies the programmable feature to be changed. The code must
be in capital letters. The following table lists the available codes.
CODE EXAMPLE
STN 1111STNnnn"01912243174"
STD 1111STDnnn"01912241559"
STE 1111STEnnn"01912243678"
STF 1111STFnnn"01912245326"
STR 1111STRnnn"07771234567"
SPT 1111SPTnn
RLT 1111RLTnn
A1T 1111A1Tnn
A1M 1111A1Mnn
NOD 1111NODnn
DIT 1111DITnn
SIG 1111SIG?
VER 1111VER?
DLE 1111DLE"123"
CDE 1111CDE1234
RLY 1111RLY
A1O 1111A1O
SDL 1111SDL"*#1345#"
BAL 1111BAL?
STM 1111STM"07771234567"
RLA 1111RLA
RUL 1111RUL
A1L 1111A1L
A1U 1111A1U
TBA 1111TBA"06002300"
CLK 1111CLK"yy/mm/dd,hh:mm"?
AUE 1111AUEnn
DTP 1111DTPn
DTD 1111DTDn
SETTINGS
nnn = 001 - 024
nnn = 001 - 024
nnn = 001 - 024
nnn = 001 - 024
nnn = 000 - 999
nn = 01 - 12
nn = 00 - 99
nn = 00 - 99
nn = 00 - 02
nn = 01 - 99
nn = 01 - 99
n/a
n/a
n/a
Any 4 digits
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
HHMMHHMM
yy/mm/dd,hh:mm n/a
nn = 00 or 01
n = 0 - 9 or X
n = 0 - 9 or X
38
DEFAULT PAGE
n/a 39
n/a 39
n/a 39
n/a 39
n/a 40
02 (40s) 40
05 (5s) 40
05 (5s) 40
01 41
0 (disabled) 41
15 (15s) 41
n/a 41
n/a 41
n/a 42
1111 42
n/a 42
n/a 42
n/a 42
n/a 42 - 43
n/a 43
n/a 43
n/a 43
n/a 43
n/a 43
00002359 44
44
01 44
X 44 - 45
X 44 - 45
66250675-EN - V1.0 - 05/09/17