Videx 4000 Series Technical Manual page 50

4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
USING ACCESS LEVELS WITH DIAL TO OPEN NUMBERS (STR)
It is also possible to assign access levels to dial to open numbers using the STR programming command (also refer to STR
programming described on pages 40 and 41). An access level can be assigned to a single DTO number or to each individual DTO
number when programming multiple DTO numbers in a single text.
Following the format of the STR programming command the following text messages can be used to store dial to open numbers
with access levels assigned to them and store them in the next available memory locations.
1111STR"n1"An
1111STR"n1"An,"n2"An
1111STR"n1"An,"n2"An,"n3"An
1111STR"n1"An,"n2"An,"n3"An,"n4"An
1111STR"n1"An,"n2"An,"n3"An,"n4"An,"n5"An
1111STR"n1"An?
1111STR"n1"An,"n2"An?
1111STR"n1"An,"n2"An,"n3"An?
1111STR"n1"An,"n2"An,"n3"An,"n4"An?
1111STR"n1"An,"n2"An,"n3"An,"n4"An,"n5"An?
Example: If memory locations 000 - 003 are already occupied with DTO numbers and following the same principle of storing
the DTO numbers in the next available location using the appropriate STR programming command shown in the
table above. Then in order to store the 3 dial to open numbers: 01912243174 (n1), 01912241558 (n2), 07771234567
(n3) with the following access levels: A3 for n1, A2 for n2 and A1 for n3 respectively the following text can then be
sent to the GSM PRO intercom to program the DTO numbers and access levels:
Including a ? at the end of the command the GSM PRO intercom will reply with the following text:
In the example the DTO numbers are stored from memory location 004 onwards as this is the next available location
and the access level for each DTO number is shown after the telephone number being stored.
CHECK/SET DATE & TIME (CLK)
The check date and time feature relies on the network providers time zone setting (also refer to important note above). After a SIM
has been placed into the GSM PRO intercom and powered up the SIM will attempt to register with the network and automatically
synchronise with the network providers time zone setting. The following text messages can be sent to the GSM PRO intercom to
check and set the current time and date. The date and time format is as follows: yy/mm/dd, hh:mm, where yy = year, mm = month,
dd = date and hh = hour, mm = minutes.
1111CLK?
1111CLK"yy/mm/dd,hh:mm"
1111CLK"yy/mm/dd,hh:mm"?
Example: Setting the current time & date to 10:05am, 18th April 2016, the following text can be sent to the GSM PRO intercom:
The GSM PRO intercom will reply with the following text:
CHECK INPUT STATUS (CHK)
IMPORTANT NOTE: This feature is only applicable when auxiliary output AO1 mode has been set to mode 02. If auxiliary output
AO1 is set to any other mode then this feature will not work (also refer to example on page 22 and setting auxiliary output AO1
mode, A1M, on page 36).
If auxiliary output AO1 (A1M) mode has been set to mode 02 then the status of this mode can be checked by sending the following
text to the GSM PRO intercom.
1111CHK?
4000 Series GSM Audio Intercom - Technical Manual
Store the dial to open number(s) DTO to the next available memory location(s),
where n1 = 1st DTO number, n2 = 2nd DTO number, n3 = 3rd DTO number, n4
= 4th DTO number, n5 = 5th DTO number and assign an access level where
An = A0 - A9.
Store the dial to open number(s) DTO to the next available memory location(s),
where n1 = 1st DTO number, n2 = 2nd DTO number, n3 = 3rd DTO number, n4
= 4th DTO number, n5 = 5th DTO number and assign an access level where
An = A0 - A9, also send confirmation text of DTO numbers, locations of where
they are stored and the access level assigned.
1111STR"01912243174"A3,"01912241558"A2,"07771234567"A1?
MEM OPEN 004 = 01912243174,A3
MEM OPEN 005 = 01912241558,A2
MEM OPEN 006 = 07771234567,A1
OK VIDEX GSM
Check current time & date and send a confirmation text back to the sender.
Set current time & date.
Set current time & date and send a confirmation text back to the sender.
1111CLK"16/04/18,10:05"?
CLK = 16/04/18, 10.05
OK VIDEX GSM
Check the current status of auxiliary output AO1 and send a confirmation text back to the
sender.
- 50 -
66250754-EN - V1.0 - 18/02/19