Videx 4000 Series Technical Manual page 59

4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
1111FDT"yyyyyyyyyyy"?
Example 1: Find dial to open location of the telephone number using the full number 01234567890, the following text can be
sent to the GSM PRO intercom:
The GSM PRO intercom will reply with the following text:
where nnn = the dial to open location of where the number is stored.
Example 2: Find dial to open location of the telephone number using the last 4 digits of the number 4567, the following text
can be sent to the GSM PRO intercom:
The GSM PRO intercom will reply with the following text:
where nnn = the dial to open location of where the number is stored.
END ON LAST DIVERT (EOD)
The end on last divert feature allows the GSM intercom to ring each programmed divert number as usual and if the divert number
is not answered it will then proceed to ring the next programmed divert number, if however there is no divert number stored the
GSM intercom will simply end the call.
By default this feature is disabled (set to 00), but can be enabled (set to 01). The following programming commands can be used to
set/check the end on divert function.
1111EODnn
1111EODnn?
1111EOD?
DOOR OR GATE (GAT)
This command feature of the GSM PRO allows the internal speech board to change the default speech annunciation that is heard
from the intercom when the onboard relay is activated. For this feature to be heard the internal speech board must be switched ON
(refer to notes on enabling or disabling the speech board, SBM, on page 43).
By default the mode of this feature is set to '01' , whereby the internal speech board will announce "the gate is open" when the
onboard relay is activated. The alternative mode can be set to '00' , whereby the internal speech board will announce "the door is
open". To set the required mode the following commands can be sent to the GSM module.
1111GATnn
1111GATnn?
1111GAT?
SHUTDOWN AND RESTART (RBT)
This command feature allows the GSM PRO intercom to be remotely shutdown and then rebooted again. The following command
can be sent to the GSM module.
1111RBT
IMPORTANT NOTE: This feature should not be confused with the 'hard-wired' reset (described on page 30). The RBT function
simply powers down the GSM module and then powers it back up again.
SIMULATE A BUTTON PRESS VIA SMS MESSAGE FOR BUTTONS 01-50 (BUT)
It is possible to simulate a button press (for the call button range 01 - 50) on the intercom by sending the following programming
command, shown below, to the GSM PRO intercom. This feature can be useful if there is suspected fault with a call button or if there
is an issue with the wiring for the buttons into the GSM's button matrix.
1111BUTnn
4000 Series GSM Audio Intercom - Technical Manual
Find dial to open location of telephone number yyyyyyyyyyy stored, where yyyyyyyyyyy
= telephone number (minimum of 4 digits).
1111FDT"01234567890"?
STORED IN nnn
OK VIDEX GSM
1111FDT"4567"?
STORED IN nnn
OK VIDEX GSM
Set end on last divert to nn, where nn = 00 (disabled) or 01 (enabled).
Set end on last divert to nn, where nn = 00 (disabled) or 01 (enabled). Also send a
confirmation text back to the sender.
Query the end on last divert status stored in the GSM module.
Set the speech board annunciation to mode nn: 01 or 00 (01 = "the gate is open", 00 = "the
door is open").
Set the speech board annunciation to mode nn: 01 or 00 (01 = "the gate is open", 00 = "the
door is open") also send a confirmation text back to sender.
Query the speech board annunciation mode set.
Shutdown and restart the GSM module.
Simulate a button press for button number nn, where nn = button number 01 - 50.
- 59 -
66250754-EN - V1.0 - 18/02/19