Videx 4000 Series Technical Manual page 40

4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
1111STNnnn"yyyyyyyyyyy"
1111STNnnn"yyyyyyyyyyy"?
1111STNnnn?
1111STNnnn""
1111STNnnn""?
nnn is a button number between 001 & 050. The telephone number y can be a maximum of 30 digits. For example: to store the
number 01912243174 for button 5 and three divert numbers (if that one is not answered or busy) of 01912241558, 07771234567
and 01912241559 respectively, the following SMS messages would be sent to the GSM intercom:
IMPORTANT NOTE: When sending the command 1111STNnnn? to query the telephone number stored for the call button the
GSM PRO will reply with the list of all the numbers stored for that call button i.e. the primary number and the 3 divert numbers
as shown in the example below *.
When sending the command 1111STDnnn? , 1111STEnnn? or 1111STFnnn? to query the individual divert numbers stored for
the call button the GSM PRO will reply with only the divert number stored for the call button, e.g. for call button 1 with divert 2
number as 07771234567 the command sent to the GSM PRO would be: 1111STE001? . The GSM PRO would reply with:
STORING THE PRIMARY AND DIVERT NUMBERS IN A SINGLE TEXT MESSAGE (USING STN)
It is also possible to program a primary telephone number and three divert numbers for a particular call button in a single text
message instead of using the individual programming codes STD (1st divert), STE (2nd divert) and STF (3rd divert). Expanding on
the STN programming command the text messages used to store/check the primary number and divert numbers are as follows.
1111STNnnn"pn" (or 1111STNnnn"yyyyyyyyyyy")
1111STNnnn"pn","d1"
1111STNnnn"pn","d1","d2"
1111STNnnn"pn","d1","d2","d3"
1111STNnnn"pn"? (or 1111STNnnn"yyyyyyyyyyy"?)
1111STNnnn"pn","d1"?
1111STNnnn"pn","d1","d2"?
1111STNnnn"pn","d1","d2","d3"?
Using the same telephone numbers from the previous example: to store the primary number 01912243174 (pn) for button 5 and
three divert numbers of 01912241558 (d1), 07771234567 (d2) and 01912241559 (d3) respectively, the following single text message
would be sent to the GSM intercom instead of sending 4 individual text messages:
1111STN005"01912243174","01912241558","07771234567","01912241559"
Similarly if only the primary number (pn) and 1st divert number (d1) were only required for button 5 the following message would
be sent:
1111STN005"01912243174","01912241558"
Remember an optional ? can be included at the end of the message to receive confirmation of the stored numbers, like so:
1111STN005"01912243174","01912241558","07771234567","01912241559"?
* The following reply will be received from the GSM PRO:
MEM 005 = 01912243174
MEM (DIVERT 1) 005 = 01912241558
MEM (DIVERT 2) 005 = 07771234567
MEM (DIVERT 3) 005 = 01912241559
OK VIDEX GSM
Remember to include " and , where appropriate.
4000 Series GSM Audio Intercom - Technical Manual
Store the primary telephone number yyyyyyyyyyy in position nnn.
Store the telephone number yyyyyyyyyy in position nnn and send a confirmation text
message to confirm storage of new number.
Query the telephone number stored in location nnn. A text message will be sent to the
sender with the stored number for that location.
Delete the telephone number stored in location nnn.
Delete the telephone number stored in location nnn. A text message will be sent to the
sender with the delete confirmation for that location.
1111STN005"01912243174"
1111STD005"01912241558"
1111STE005"07771234567"
1111STF005"01912241559"
MEM (DIVERT 2)
001 = 0771234567
OK VIDEX GSM
Store the primary number and respective divert numbers in position nnn,
(where pn = primary number, d1= 1st divert, d2 = 2nd divert, d3 = 3rd divert
and nnn = call button 001 - 050).
Store the primary number and respective divert numbers in position nnn,
(where pn = primary number, d1= 1st divert, d2 = 2nd divert, d3 = 3rd divert
and nnn = call button 001 - 050), also send confirmation of stored numbers
for that location.
- 40 -
66250754-EN - V1.0 - 18/02/19