Videx 4000 Series Technical Manual page 58

4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
for 5 seconds then the relay will activate for 5 seconds at the beginning of the timeband and then activate again for 5 seconds at
the end of the timeband.
The following text messages can be used to setup the free access timebands to activate the GSM PRO's relay or either of the auxiliary
outputs and setup the selected output for latch or momentary trigger. For the list of days refer to the Days table on page 47.
1111FREn"HHMMHHMM"days:m:o
1111FREn"HHMMHHMM"days:m:o?
1111FREn?
Example: To program free access timeband number 7 to latch the GSM PRO's relay between 7:45am until 10:45am for the weekend
only, the following text can be sent to the GSM PRO intercom:
Note that in this example no comma , is required to separate the time period and days selection. A ? has been
included to receive a confirmation text. The GSM PRO intercom will reply with the following text:
In this example the reply from the GSM PRO confirms the relay has been setup to latch for the weekend only (Saturday
Sa and Sunday Su) for free access timeband number 7 between 7:45am until 10:45am.
IMPORTANT NOTE: If the selected output (relay: RL, auxiliary 1: A1 or auxiliary 2: A2) is setup for a momentary trigger the
output will trigger for the programmed output time. Remember to set the output time using the respective programming
code, i.e. for the relay use 1111RLTnn?, for auxiliary 1 use 1111A1Tnn? and for auxiliary 2 use 1111A2Tnn?
It should also be noted that when any of the outputs have been setup with free access the free access feature takes priority over
other programming or modes that may have been setup for the output.
CLEAR ALL FREE ACCESS TIMEBANDS (FRD)
It is also possible to clear and reset all the free access timebands. The following text message can be used clear all the free access
timebands.
1111FRD?
DISABLE OR ENABLE SPEECH BOARD (SBM)
The GSM PRO intercom includes call progress speech annunciation which can be disabled (01) or enabled (02). The default setting
for this function is enabled. The following text messages can be used to enable or disable this feature.
1111SBMnn
1111SBMnn?
1111SBM?
SET SPEECH BOARD VOLUME (SBV)
The volume setting of the speech board in the GSM PRO intercom can be adjusted. The default volume level is set to 75, but can be
set anywhere between 00 (low) up to 99 (high). The following text messages can be used to increase or decrease the volume level
and query the current speech board volume setting stored.
1111SBVnn
1111SBVnn?
1111SBV?
FIND A TELEPHONE NUMBER (FDT)
The find a telephone number feature allows the user to find the dial to open location (between 000 - 999) of where a particular
telephone number is stored in the GSM PRO intercom. It can locate the number either from using the full telephone number or a
minimum of the last 4 digits of a number (see following examples). The following text messages can be used.
4000 Series GSM Audio Intercom - Technical Manual
Store the time period for free access timeband n, where n = timeband no. (0 - 9) using
this format: the first HHMM is the start time to be active from (i.e. 0845 for 8:45am in the
morning) and the second HHMM is the end time that will stop being active from (i.e. 1930
for 7:30pm at night), where days = Mo, Tu, We, Th, Fri, Sa, Su, AD, WD, WE, output trigger
m = L for latch or M for momentary and output selection o = RL for relay, A1 for auxiliary
1 and A2 for auxiliary 2.
As above and also send a confirmation text back to the sender of programmed free access
timeband period including day(s) active for, output trigger and output selection.
Query the information stored for free access timeband n, where n = free access timeband
number (0 - 9), also send a confirmation text back to the sender.
1111FRE7"07451045"WE:L:RL?
FA7 =07451045,Su,Sa,L,RL
OK VIDEX GSM
Delete all free access timebands, also send a confirmation text back to the sender.
Disable or enable speech board nn: 01 or 02 (01 = disabled, 02 = enabled).
Disable or enable speech board nn: 01 or 02 (01 = disabled, 02 = enabled), also send a
confirmation text back to the sender.
Query the speech board status.
Increase or decrease speech board volume nn, where nn = 00 (low) - 99 (high).
Increase or decrease speech board volume nn, where nn = 00 (low) - 99 (high), also send a
confirmation text back to the sender.
Query the speech board volume setting.
- 58 -
66250754-EN - V1.0 - 18/02/19