Programming The Gsm Intercom - Videx GSM4K/4G Technical Manual

4000 Series GSM Audio Intercom with Proximity

Programming the GSM Intercom

PROGRAMMING THE GSM INTERCOM
Programming the 4G GSM intercom can be carried out by one of the following methods: sending text (SMS) messages, by using the
GSMSK PC software (ver 4.1.0.35 or later), also refer to the programming manual GSMSK_66251720-EN_V2-1 (or later) or by using
the GSM mobile apps: Videx SMS Wizard (for administrators) and the Videx SMS Wizard PRO (for installers and engineers) also see
additional notes on page 67.
IMPORTANT NOTE: When you are required to use " in a text message it is important to use the correct symbol and not for example
' or two ' single apostrophes side by side which may look the same, but will be interpreted differently by the GSM intercom.
PROGRAMMING BY TEXT MESSAGE
Programming by text message is a simple way to customise the settings of the GSM intercom and add or delete telephone numbers.
If you have several buttons or telephone numbers to enter you may find programming easier with the GSMSK PC software. Simply
send texts in the following format shown below to the telephone number of the SIM within the GSM intercom panel:
< 4 DIGIT CODE > < 3 DIGIT FUNCTION CODE > < OPTIONAL DATA > < OPTIONAL ? >
4 DIGIT CODE
3 DIGIT FUNCTION CODE
DESCRIPTION
Store a primary telephone no.
Store divert 1 telephone no.
Store divert 2 telephone no.
Store divert 3 telephone no.
Store a primary telephone no.
and divert no's in a single text
message
Store a dial to open no. (DTO)
or
Store up to 5 dial to open no's
(DTO) in a single text message to
the next available locations
Delete a dial to open no. (DTO)
without knowing it's location
Store a temporary dial to open
no. (DTO), store up to 32 temp
no's max.
Set call time
Set relay time
Set auxiliary AO1 output time
Set auxiliary AO1 out mode
Set auxiliary AO2 output time
Divert to next no. time
Check GSM signal strength
Check software version
Dial a number
Store SMS message for g-4
Change 4 digit code
Trigger the relay
Trigger the auxiliary output AO1 A1O
Trigger the auxiliary output AO2 A2O
4000 Series GSM Audio Intercom - Technical Manual
This code prevents unauthorised access to the programmable features of the system. The code must
be four digits long, but can be any combination using digits 0 – 9. The default code is "1111" and will be
used for all examples in this manual.
The 3 digit function or command code identifies the programmable feature to be changed. The code
must be in capital letters. The following table lists the available codes.
CODE EXAMPLE
STN 1111STNnnn"01912243174"
STD 1111STDnnn"01912241559"
STE 1111STEnnn"01912243678"
STF 1111STFnnn"01912245326"
STN 1111STNnnn"pn", " d1", " d2", " d3"
1111STNnnn"01912243174",
"01912241559", " 01912243678",
"01912245326"
STR 1111STRnnn"07771234567"
1111STR"n1", " n2", " n3", " n4", " n5"
1111STR"01912243174",
"01912241559", " 01912243678",
"01912245326", " 07897123456"
DET 1111DET"01912243174"
TDR 1111TDR"tele"T?
(note: if T is omitted default time
T = 8 hours)
SPT 1111SPTnn
RLT 1111RLTnn
A1T 1111A1Tnn
A1M 1111A1Mnn
A2T 1111A2Tnn
DIT 1111DITnn
SIG 1111SIG?
VER 1111VER?
DLE 1111DLE"123"
SMS 1111SMS"HouseAlarm"
CDE 1111CDE1234
RLY 1111RLY
1111A1O
1111A2O
SETTINGS
nnn = 001 - 050
nnn = 001 - 050
nnn = 001 - 050
nnn = 001 - 050
nnn = 001 - 050
pn = primary no.
d1 = divert 1 no.
d2 = divert 2 no.
d3 = divert 3 no.
nnn = 000 - 999 or
nnn = optional
n1 = 1st DTO
n2 = 2nd DTO
n3 = 3rd DTO
n4 = 4th DTO
n5 = 5th DTO
n/a
tele = tel no. to
store
T = 1 - 255 hrs
nn = 01 - 12
nn = 00 - 99
nn = 00 - 99
nn = 00 - 05
nn = 00 - 99
nn = 01 - 99
n/a
n/a
n/a
n/a
Any 4 digits
n/a
n/a
n/a
- 37 -
DEFAULT PAGE
n/a 40 - 42
n/a 40 - 42
n/a 40 - 42
n/a 40 - 42
n/a 40 - 41
n/a 41 - 42
n/a 42 - 43
n/a 43
02 (40s)
43
05 (5s)
43
05 (5s)
43
01 43 - 44
05 (5s)
44
15 (15s)
44
n/a 44
n/a 44
n/a 44 - 45
AUX TRIG 45
1111 45
n/a 45
n/a 45
n/a 45
66250754-4G-EN - V2.0 - 28/03/22