Videx 4000 Series Technical Manual page 51

4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
Example:
Check the current status of auxiliary output AO1, the following text can be sent to the GSM PRO intercom:
The GSM PRO intercom will reply with either of the following texts:
SILENT DIALLING MODE (AUE)
When the GSM PRO intercom is calling the telephone number stored there is a choice of either hearing the ringing noise from the
intercom panel or just hearing beeps to indicate a call is in progress.
• Ringing heard during calling: nn = 01
• Beeps heard during calling: nn = 00
The following text messages can be sent to the GSM PRO intercom to enable (00), disable (01) or query the setting of the silent
dialling feature.
1111AUEnn
1111AUEnn?
1111AUE?
SEND DTMF TONE AFTER CALL ANSWERED FOR CALL BUTTON 1(DTP, DTD AND DTT)
It is possible to set the GSM PRO intercom to send a DTMF tone after a call is answered. This option is only available for both the
primary number of button 1 and the divert 1 number for button 1. This feature is useful if the intercom is dialling into a telephone
system where an automated menu is present and a DTMF tone is required to select a particular option from the menu. This feature
is disabled by default. The following programming text messages allow the user to setup the DTMF tone(s) required.
• The DTP command sets the DTMF tone required (from 0 - 9) after a call is answered for button 1.
• The DTD command sets the DTMF tone required (from 0 - 9) after divert 1 call is answered for button 1.
• The DTT command sets the delay time from when the call is answered to when the DTMF is sent.
SET DTMF TONE REQUIRED FOR BUTTON 1 PRIMARY CALL
1111DTPn
1111DTPn?
SET DTMF TONE REQUIRED FOR BUTTON 1 DIVERT CALL
1111DTDn
1111DTDn?
SET THE DELAY TIME FROM WHEN THE CALL IS ANSWERED TO WHEN THE DTMF TONE IS SENT
1111DTTnn
1111DTTnn?
QUERY THE SETTINGS
1111DTP?
1111DTD?
1111DTT?
ENABLE THE DIAL '0' ON ANSWER FUNCTION (EDZ)
When enabled this feature allows an incoming call to be diverted to the programmed divert telephone number if the '0' button on
the telephone has not been pressed after answering the call. This can be useful if the user's number has an answerphone service (or
answer machine) and they do not want the call to be answered by this service or if the primary number (mobile no.) is switched off.
The default for this function is disabled (set to 00). The following texts can be used to enable or disable this function.
4000 Series GSM Audio Intercom - Technical Manual
1111CHK?
IN = OP
or
OK VIDEX GSM
(status open)
Set the silent dialling mode nn: 01 or 00.
Set the silent dialling mode nn: 01 or 00 and send a confirmation text back to the sender.
Query the current mode stored. A text message will be sent back to the sender confirming
which silent dialling mode has been set.
Set DTMF tone required, where n = 0 - 9 for DTMF tones 0 - 9 or X to disable this feature
(for button 1).
Set DTMF tone required, where n = 0 - 9 for DTMF tones 0 - 9 or X to disable this feature.
Also send a confirmation text back to the sender with the stored DTMF tone setting (for
button 1).
Set DTMF tone required, where n = 0 - 9 for DTMF tones 0 - 9 or X to disable this feature
(for divert 1).
Set DTMF tone required, where n = 0 - 9 for DTMF tones 0 - 9 or X to disable this feature.
Also send a confirmation text back to the sender with the stored DTMF tone setting (for
divert 1).
Set the time nn, where nn = 01 - 12 seconds.
Set the time nn, where nn = 01 - 12 seconds and also send a confirmation text back to the
sender of the time stored.
Query the DTMF tone set, replies TP = n, where n = 0 - 9 or X.
Query the DTMF tone set, replies TD = n, where n = 0 - 9 or X.
Query the delay time set, replies TT = nn, where nn = 01 - 12 seconds.
- 51 -
IN = CL
OK VIDEX GSM
(status closed)
66250754-EN - V1.0 - 18/02/19