Videx 4000 Series Technical Manual page 47

4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
1111A2L?
UNLATCH AUXILIARY OUTPUT AO2 (A2U)
Auxiliary output AO2 can also be unlatched. To unlatch auxiliary output AO2 the following text message can be sent to the GSM
PRO intercom.
1111A2U
1111A2U?
STORE TIMEBAND FOR CALLS TO BE ACTIVE FOR (TBA)
IMPORTANT NOTE: This feature relies on the network providers time zone setting and also if they support NITZ (Network Identity
and Time Zone). First check the time/date is correct by sending the SMS message 1111CLK? (also refer to check intercoms time
& date feature below). If the time/date returned is incorrect, it maybe that they do not support it. The clock can be set manually
but any power cut will result in the time and date being lost unless battery backup is included.
The timeband feature allows the call buttons to be disabled or diverted to the master telephone number outside a certain time
window. For example, if the timeband is set from 6:00am to 11:30pm then the user will only receive calls between the hours of 06:00
in the morning until 23:30 at night. Remember to always use the 24hr clock and also ensure the start time is earlier than the stop
time. The timeband can also be set for a specific day or days of the week to be active for by adding the day or days to the end of the
programming command, see table below for the codes used for the days required.
Mo = Monday
Sa = Saturday
When including the day or days in the command they must be separated using a comma , between the codes required, also refer
to the examples below. Use the following text messages to store, query and delete the timeband.
1111TBA"HHMMHHMM",days
1111TBA"HHMMHHMM",days?
1111TBA?
1111TBA""
1111TBA""?
Example 1: To set a timeband where the calls are to be received on all days of the week from 8:00am in the morning up
until 5:00pm in the evening where they would finish, the following text can be sent to the GSM PRO intercom,
remembering to use 24hr clock notation:
The GSM PRO intercom will reply with the following text:
Example 2: To set a timeband where calls are to be received on Mondays, Tuesdays and Fridays only, from 10:00am until 3:30pm,
the following text can be sent to the GSM PRO intercom:
Note that commas , are used where appropriate to separate the days required for the timeband. The GSM PRO
intercom will reply with the following text:
Note that in both examples shown the confirmation text message from the GSM PRO will include the day or days of
the week shown after the timeband period.
STORE TIMEBAND FOR ACCESS CONTROL: PROXIMITY, ACCESS CODES & DIAL TO OPEN TO BE ACTIVE FOR (ATB)
This function together with the access levels feature (ACC), described further on, allows the additional access control features,
i.e. proximity fobs/cards (000 - 999) and coded access features (codes 000 - 399 and temp codes 00 - 31) of the GSM PRO and also
the dial to open numbers (DTO) to be programmed with up to 10 access control timebands (0 - 9). Whether using the built-in
proximity reader on its own or a combination of the off board proximity readers (Art.4850R) and keypads (Art.4903) the access
control timebands can be used to manage access rights (i.e. when fobs/cards or access codes can be active for on the proximity
4000 Series GSM Audio Intercom - Technical Manual
Latch auxiliary output AO2 and send a confirmation text back to the sender.
Unlatch auxiliary output AO2.
Unlatch auxiliary output AO2 and send a confirmation text back to the sender.
Tu = Tuesday We = Wednesday
Su = Sunday
Store the time using this format. The first HHMM is the start time to receive calls (i.e. 0600
for 6am in the morning) and the second HHMM is the time to stop receiving calls (i.e. 2330
for 11:30pm at night) and where days = Mo, Tu, We, Th, Fri, Sa, Su, AD, WD, WE.
As above but also send a confirmation text back to the sender with the stored setting.
Query timeband setting. A text message will be sent to the sender with the stored time
band and days active for.
Delete the timeband and allow calls to be received at any time.
Delete and confirm deletion of the timeband.
1111TBA"08001700",AD?
TB = 08001700,Su,Mo,Tu,We,Th,Fr,Sa
OK VIDEX GSM
1111TBA"10001530",Mo,Tu,Fr?
TB = 10001530,Mo,Tu,Fr
OK VIDEX GSM
Days
AD = All days WD = Week days only
- 47 -
Th = Thursday
WE = Weekends only
66250754-EN - V1.0 - 18/02/19
Fr = Friday