Revision History - Xilinx Zynq-7000 Getting Started Manual

Revision History

The following table shows the revision history for this document.
Date Version
05/25/2012 1.0
05/29/2012 1.1
06/21/2012 1.2
09/18/2012 2.0
11/12/2012 2.1
01/24/2013 3.0
ZC702 and ZVIK Getting Started Guide
UG926 (v6.0) December 17, 2013
Initial Xilinx release.
Added Figure 4-3 and the text just before and after it.
Chapter 1, Introduction: Added a "Reference Designs and Demonstrations" group to
section ZC702 Evaluation Kit Contents, page
JTAG to Digilent USB-to-JTAG. Added that the SD MMC card contains bootable
configuration files for the Base TRD demo design files and Linux applications
platform. Updated USB JTAG interface information and added details to the clock
sources list in section For reference design files, documents, and board source files,
go to the Zynq-7000 AP SoC Video and Imaging Kit documentation page., page
Changed FMC1 and FMC2 connector types to LPC I/O expansion connectors. Added
tables of default settings to the section
Chapter 2, ZC702 Evaluation Kit Built-In
Introduction, page 15. Added bring-up details through the chapter. Settings were
added to section Run the BIST Application, page
Added Chapter 3, Getting Started with the Base Targeted Reference
Added Chapter 4, Using the AMS101 Evaluation
Additional references were added through the book and to
Resources.
The ZC702 evaluation kit now includes a USB Micro-B to female A adapter. Added
information about the Zynq-7000 AP SoC Video and Imaging Kit (ZVIK) to the
Overview, page 7 and a new section
Contents, page 10. Photos are updated in
Board and Figure 2-2: ZC702 with the UART and Power Cable Attached. The
Demonstration Procedure, page 30
application using an external video source supporting use of the ZVIK. Added
Table 3-1 and Table 3-2. Added support for 720p video resolution in the video demo
application in Running the Video Demonstration for 720p Video Resolution, page
Updated for ISE® Design Suite v14.3. Document and web site references changed
throughout the book. In BIST Setup Requirements, page
power cable for the ZC702 board" was removed. In
page 16, step 1 changed. In
changed. An introduction was added to
"1 GB DDR3 running at 533 MHz" was removed. In
Requirements, page 28, zImage and ramdisk8M.image.gz became uImage and
uramdisk8M.image.gz. The USB stick (or key) is not included in the kit. Instead,
download files from the ZC702 Product Page at
the Docs & Designs tab. Standoffs and a new
details were added to TRD Demonstration Procedure, page
Figure 3-7 were replaced to illustrate the QT-based GUI and minimized GUI mode.
USB key was removed from
Updated for ISE Design Suite 14.5. Revised eighth bullet on
sentence ending in "to exercise the portions of the demo ..." to be "use the frame
buffer console terminal that will come up, once user exit the demo." Added third note
on page 29. Revised Figure 3-6, page 33
www.xilinx.com
Revision
8. Changed cable from Digilent USB
Default Jumper and Switch Settings, page
Self-Test: Updated switch settings in the
22.
Card.
Zynq-7000 AP SoC Video and Imaging Kit
Figure 1-3: Feature Callout for the ZC702
adds information on how to demo the video
ZC702 Evaluation Board Setup,
Install the USB-UART Driver, page 18,step 1
Chapter 3. In Base TRD Key Features, page
Base TRD Hardware Setup
www.xilinx.com/zc702
Figure 3-3
Chapter 4. Next Steps became
and Figure 3-7, page
10.
11.
Design.
Appendix A, Additional
TRD
15, "A power adapter and
and step 2
27,
and click on
showing mounting hardware
30. Figure 3-6 and
Chapter 5.
page 28 to replace
34.
Send Feedback
38.
3